Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH A 2.5L ENGINE, THE CRANKSHAFT POSITION SENSOR CAN OVERHEAT CAUSING A BRIEF INTERRUPTION IN THE SIGNAL OUTPUT FROM THE SENSOR.
ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH A 2.5L ENGINE, THE CRANKSHAFT POSITION SENSOR CAN OVERHEAT CAUSING A BRIEF INTERRUPTION IN THE SIGNAL OUTPUT FROM THE SENSOR.
ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH A 2.5L ENGINE, THE CRANKSHAFT POSITION SENSOR CAN OVERHEAT CAUSING A BRIEF INTERRUPTION IN THE SIGNAL OUTPUT FROM THE SENSOR.
ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH A 2.5L ENGINE, THE CRANKSHAFT POSITION SENSOR CAN OVERHEAT CAUSING A BRIEF INTERRUPTION IN THE SIGNAL OUTPUT FROM THE SENSOR.
ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH A 2.5L ENGINE, THE CRANKSHAFT POSITION SENSOR CAN OVERHEAT CAUSING A BRIEF INTERRUPTION IN THE SIGNAL OUTPUT FROM THE SENSOR.
CERTAIN TYC HALOGEN TYPE HEADLAMP ASSEMBLIES P/N 20-6644-00 SOLD AS AFTERMARKET EQUIPMENT FOR 2005-2006 NISSAN ALTIMA PASSENGER VEHICLES. THE PHOTOMETRIC WERE MISALIGNED WHICH DOES NOT COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
CERTAIN TYC HALOGEN TYPE HEADLAMP ASSEMBLIES P/N 20-6644-00 SOLD AS AFTERMARKET EQUIPMENT FOR 2005-2006 NISSAN ALTIMA PASSENGER VEHICLES. THE PHOTOMETRIC WERE MISALIGNED WHICH DOES NOT COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
CERTAIN SPORT UTILITY VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 210, 'SEAT BELT ASSEMBLY ANCHORAGES.' THE DRIVER'S SIDE THIRD ROW SEAT BELT UPPER ANCHOR BRACKET MAY BE CRACKED.
CERTAIN SPORT UTILITY VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 210, 'SEAT BELT ASSEMBLY ANCHORAGES.' THE DRIVER'S SIDE THIRD ROW SEAT BELT UPPER ANCHOR BRACKET MAY BE CRACKED.
ON CERTAIN VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, IOWA, ILLINOIS, INDIANA, KENTUCKY, MASSACHUSETTS, MAINE, MARYLAND, MICHIGAN, MINNESOTA, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, TENNESSEE, VERMONT, VIRGINIA, WEST VIRGINIA , WISCONSIN AND THE DISTRICT OF COLUMBIA, DURING THE COATING PROCESS OF THE FUEL FILLER TUBE ASSEMBLY, AN INSUFFICIENT AMOUNT OF COATING MAY HAVE BEEN APPLIED AT THE LOWER MOUNTING BRACKET. THIS COULD RESULT IN AN OPENING IN THE COATING WHICH CAN ALLOW WATER TO ENTER AND MAKE CONTACT WITH THE BARE METAL OF THE TUBE.
ON CERTAIN VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, IOWA, ILLINOIS, INDIANA, KENTUCKY, MASSACHUSETTS, MAINE, MARYLAND, MICHIGAN, MINNESOTA, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, TENNESSEE, VERMONT, VIRGINIA, WEST VIRGINIA , WISCONSIN AND THE DISTRICT OF COLUMBIA, DURING THE COATING PROCESS OF THE FUEL FILLER TUBE ASSEMBLY, AN INSUFFICIENT AMOUNT OF COATING MAY HAVE BEEN APPLIED AT THE LOWER MOUNTING BRACKET. THIS COULD RESULT IN AN OPENING IN THE COATING WHICH CAN ALLOW WATER TO ENTER AND MAKE CONTACT WITH THE BARE METAL OF THE TUBE.
ON CERTAIN VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, IOWA, ILLINOIS, INDIANA, KENTUCKY, MASSACHUSETTS, MAINE, MARYLAND, MICHIGAN, MINNESOTA, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, TENNESSEE, VERMONT, VIRGINIA, WEST VIRGINIA , WISCONSIN AND THE DISTRICT OF COLUMBIA, DURING THE COATING PROCESS OF THE FUEL FILLER TUBE ASSEMBLY, AN INSUFFICIENT AMOUNT OF COATING MAY HAVE BEEN APPLIED AT THE LOWER MOUNTING BRACKET. THIS COULD RESULT IN AN OPENING IN THE COATING WHICH CAN ALLOW WATER TO ENTER AND MAKE CONTACT WITH THE BARE METAL OF THE TUBE.
ON CERTAIN VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, IOWA, ILLINOIS, INDIANA, KENTUCKY, MASSACHUSETTS, MAINE, MARYLAND, MICHIGAN, MINNESOTA, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, TENNESSEE, VERMONT, VIRGINIA, WEST VIRGINIA , WISCONSIN AND THE DISTRICT OF COLUMBIA, DURING THE COATING PROCESS OF THE FUEL FILLER TUBE ASSEMBLY, AN INSUFFICIENT AMOUNT OF COATING MAY HAVE BEEN APPLIED AT THE LOWER MOUNTING BRACKET. THIS COULD RESULT IN AN OPENING IN THE COATING WHICH CAN ALLOW WATER TO ENTER AND MAKE CONTACT WITH THE BARE METAL OF THE TUBE.
ON CERTAIN VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, IOWA, ILLINOIS, INDIANA, KENTUCKY, MASSACHUSETTS, MAINE, MARYLAND, MICHIGAN, MINNESOTA, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, TENNESSEE, VERMONT, VIRGINIA, WEST VIRGINIA , WISCONSIN AND THE DISTRICT OF COLUMBIA, DURING THE COATING PROCESS OF THE FUEL FILLER TUBE ASSEMBLY, AN INSUFFICIENT AMOUNT OF COATING MAY HAVE BEEN APPLIED AT THE LOWER MOUNTING BRACKET. THIS COULD RESULT IN AN OPENING IN THE COATING WHICH CAN ALLOW WATER TO ENTER AND MAKE CONTACT WITH THE BARE METAL OF THE TUBE.
CERTAIN EAGLE EYES HEADLAMP ASSEMBLIES, P/NOS. DS517-B001L AND DS517-B001R, SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR THE ABOVE LISTED PASSENGER VEHICLES. THE OPTICEL SURFACE OF THE REFLECTOR IS CORRODED INHIBITING THE PERFORMANCE OF THE UPPER AND LOWER BEAMS WHICH FAILS TO CONFORM TO THE PHOTOMETRIC REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
CERTAIN EAGLE EYES HEADLAMP ASSEMBLIES, P/NOS. DS517-B001L AND DS517-B001R, SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR THE ABOVE LISTED PASSENGER VEHICLES. THE OPTICEL SURFACE OF THE REFLECTOR IS CORRODED INHIBITING THE PERFORMANCE OF THE UPPER AND LOWER BEAMS WHICH FAILS TO CONFORM TO THE PHOTOMETRIC REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
CERTAIN EAGLE EYES HEADLAMP ASSEMBLIES, P/NOS. DS517-B001L AND DS517-B001R, SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR THE ABOVE LISTED PASSENGER VEHICLES. THE OPTICEL SURFACE OF THE REFLECTOR IS CORRODED INHIBITING THE PERFORMANCE OF THE UPPER AND LOWER BEAMS WHICH FAILS TO CONFORM TO THE PHOTOMETRIC REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
CERTAIN EAGLE EYES HEADLAMP ASSEMBLIES, P/NOS. DS517-B001L AND DS517-B001R, SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR THE ABOVE LISTED PASSENGER VEHICLES. THE OPTICEL SURFACE OF THE REFLECTOR IS CORRODED INHIBITING THE PERFORMANCE OF THE UPPER AND LOWER BEAMS WHICH FAILS TO CONFORM TO THE PHOTOMETRIC REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
CERTAIN EAGLE EYES HEADLAMP ASSEMBLIES, P/NOS. DS517-B001L AND DS517-B001R, SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR THE ABOVE LISTED PASSENGER VEHICLES. THE OPTICEL SURFACE OF THE REFLECTOR IS CORRODED INHIBITING THE PERFORMANCE OF THE UPPER AND LOWER BEAMS WHICH FAILS TO CONFORM TO THE PHOTOMETRIC REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.
CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.
CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.
CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.
CERTAIN ANZO AFTERMARKET HEADLIGHTS, P/N 02-AZ-NA02-B-A, SOLD FOR USE ON 2002-2004 NISSAN ALTIMA VEHICLES. DURING PRODUCTION THE LAMP HOUSING SHAPE DEFORMED DISTORTING THE ASSEMBLY ANGLE OF THE REFLECTOR AND INFLUENCED THE AIMING POSITION. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
CERTAIN ANZO AFTERMARKET HEADLIGHTS, P/N 02-AZ-NA02-B-A, SOLD FOR USE ON 2002-2004 NISSAN ALTIMA VEHICLES. DURING PRODUCTION THE LAMP HOUSING SHAPE DEFORMED DISTORTING THE ASSEMBLY ANGLE OF THE REFLECTOR AND INFLUENCED THE AIMING POSITION. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
CERTAIN ANZO AFTERMARKET HEADLIGHTS, P/N 02-AZ-NA02-B-A, SOLD FOR USE ON 2002-2004 NISSAN ALTIMA VEHICLES. DURING PRODUCTION THE LAMP HOUSING SHAPE DEFORMED DISTORTING THE ASSEMBLY ANGLE OF THE REFLECTOR AND INFLUENCED THE AIMING POSITION. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
CERTAIN MAXZONE HEADLIGHT ASSEMBLIES, DEPO BRAND, P/NOS. 315-1145L-AS AND 315-1145R-AS, SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR THE ABOVE LISTED PASSENGER VEHICLES. DURING PRODUCTION THE LAMP REFLECTOR SHAPE DEFORMED CHANGING THE SHAPE OF THE OPTIC SURFACE. THIS WILL CHANGE THE OPPOSITE POSITION OF LOW BEAM AND HIGH BEAM OPTICSAND CHANGE THE ANGLE OF INCIDENCE AND ILLUMATED LOCATION WHICH FAILS TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
CERTAIN MAXZONE HEADLIGHT ASSEMBLIES, DEPO BRAND, P/NOS. 315-1145L-AS AND 315-1145R-AS, SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR THE ABOVE LISTED PASSENGER VEHICLES. DURING PRODUCTION THE LAMP REFLECTOR SHAPE DEFORMED CHANGING THE SHAPE OF THE OPTIC SURFACE. THIS WILL CHANGE THE OPPOSITE POSITION OF LOW BEAM AND HIGH BEAM OPTICSAND CHANGE THE ANGLE OF INCIDENCE AND ILLUMATED LOCATION WHICH FAILS TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
CERTAIN MAXZONE HEADLIGHT ASSEMBLIES, DEPO BRAND, P/NOS. 315-1145L-AS AND 315-1145R-AS, SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR THE ABOVE LISTED PASSENGER VEHICLES. DURING PRODUCTION THE LAMP REFLECTOR SHAPE DEFORMED CHANGING THE SHAPE OF THE OPTIC SURFACE. THIS WILL CHANGE THE OPPOSITE POSITION OF LOW BEAM AND HIGH BEAM OPTICSAND CHANGE THE ANGLE OF INCIDENCE AND ILLUMATED LOCATION WHICH FAILS TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
CERTAIN HOPKINS AFTERMARKET TRAILER BRAKE CONTROL CONNECTION HARNESSES SOLD FOR USE ON CERTAIN MODELS OF NISSAN VEHICLES WHICH ARE LISTED ABOVE. THE INTERNAL PART NUMBERS WITHIN HOPKINS ARE: 1010476025, 1040376025, 1110476025, 1170376025, 1290376025, 1010476035, 1040376035, 1110476035, 1170376035, AND 1290376035. A WIRE MAY HAVE BEEN PLACED IN AN INCORRECT POSITION IN THE ELECTRICAL CONNECTOR HOUSING. THIS RESULTS IN AN INCORRECT ROUTING OF WIRES BETWEEN THE TRAILER BRAKE CONTROLLER AND THE TOWING VEHICLE WIRING SYSTEM.
