Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
AIR SYSTEM BLOCKAGE IN THE AIR DRYER OCCURS DEGRADING THE MOISTURE REMOVING CAPABILITIES OF THE DRYER WHEN THE VEHICLE IS OPERATED IN A COLD ENVIRONMENT AND MOISTURE ACCUMULATES AND FREEZES IN THE AIR DRYER OR IN THE LINE BETWEEN THE DRYER AND THE AIR SYSTEM RESERVOIR. THE AIR DRYER CAN BECOME OVERPRESSURIZED CAUSING THE AIR DRYER CARTRIDGE TO SEPARATE FROM THE MOUNTING BASE.
AIR SYSTEM BLOCKAGE IN THE AIR DRYER OCCURS DEGRADING THE MOISTURE REMOVING CAPABILITIES OF THE DRYER WHEN THE VEHICLE IS OPERATED IN A COLD ENVIRONMENT AND MOISTURE ACCUMULATES AND FREEZES IN THE AIR DRYER OR IN THE LINE BETWEEN THE DRYER AND THE AIR SYSTEM RESERVOIR. THE AIR DRYER CAN BECOME OVERPRESSURIZED CAUSING THE AIR DRYER CARTRIDGE TO SEPARATE FROM THE MOUNTING BASE.
AIR SYSTEM BLOCKAGE IN THE AIR DRYER OCCURS DEGRADING THE MOISTURE REMOVING CAPABILITIES OF THE DRYER WHEN THE VEHICLE IS OPERATED IN A COLD ENVIRONMENT AND MOISTURE ACCUMULATES AND FREEZES IN THE AIR DRYER OR IN THE LINE BETWEEN THE DRYER AND THE AIR SYSTEM RESERVOIR. THE AIR DRYER CAN BECOME OVERPRESSURIZED CAUSING THE AIR DRYER CARTRIDGE TO SEPARATE FROM THE MOUNTING BASE.
THE LABELS REMINDING OPERATORS CLOSING THE FUEL TANK CROSSOVER VALVES TO REOPEN THE VALVES BEFORE OPERATING THE ENGINES WERE OMITTED. IF THE TANKS ARE OVER HALF FULL AND VEHICLE OPERATION WAS RESUMED WITHOUT REOPENING THE FUEL TANK CROSS-OVER VALVES, PRESSURE COULD BUILD IN ONE OF THE TANKS.
THE LABELS REMINDING OPERATORS CLOSING THE FUEL TANK CROSSOVER VALVES TO REOPEN THE VALVES BEFORE OPERATING THE ENGINES WERE OMITTED. IF THE TANKS ARE OVER HALF FULL AND VEHICLE OPERATION WAS RESUMED WITHOUT REOPENING THE FUEL TANK CROSS-OVER VALVES, PRESSURE COULD BUILD IN ONE OF THE TANKS.
THE LABELS REMINDING OPERATORS CLOSING THE FUEL TANK CROSSOVER VALVES TO REOPEN THE VALVES BEFORE OPERATING THE ENGINES WERE OMITTED. IF THE TANKS ARE OVER HALF FULL AND VEHICLE OPERATION WAS RESUMED WITHOUT REOPENING THE FUEL TANK CROSS-OVER VALVES, PRESSURE COULD BUILD IN ONE OF THE TANKS.
THE LABELS REMINDING OPERATORS CLOSING THE FUEL TANK CROSSOVER VALVES TO REOPEN THE VALVES BEFORE OPERATING THE ENGINES WERE OMITTED. IF THE TANKS ARE OVER HALF FULL AND VEHICLE OPERATION WAS RESUMED WITHOUT REOPENING THE FUEL TANK CROSS-OVER VALVES, PRESSURE COULD BUILD IN ONE OF THE TANKS.
SECONDARY SERVICE RESERVOIR AIR CHECK VALVES MAY NOT SEAT PROPERLY DUE TO A MECHANICAL INTERFERENCE CONDITION BETWEEN A CIRCULAR BRASS GUIDE AND THE WALL OF A CYLINDRICAL FERRULE IN WHICH THE BRASS GUIDE IS INTENDED TO MOVE FREELY.
SECONDARY SERVICE RESERVOIR AIR CHECK VALVES MAY NOT SEAT PROPERLY DUE TO A MECHANICAL INTERFERENCE CONDITION BETWEEN A CIRCULAR BRASS GUIDE AND THE WALL OF A CYLINDRICAL FERRULE IN WHICH THE BRASS GUIDE IS INTENDED TO MOVE FREELY.
HAND THROTTLE CONTROLS WERE NOT IDENTIFIED EITHER ON THE CONTROL KNOB OR ON THE INSTRUMENT PANEL AS REQUIRED BY FMVSS 101. CONSEQUENCE OF DEFECT: TRUCKS ARE NOT IN COMPLIANCE WITH FMVSS 101, CONTROLS AND DISPLAYS.
HAND THROTTLE CONTROLS WERE NOT IDENTIFIED EITHER ON THE CONTROL KNOB OR ON THE INSTRUMENT PANEL AS REQUIRED BY FMVSS 101. CONSEQUENCE OF DEFECT: TRUCKS ARE NOT IN COMPLIANCE WITH FMVSS 101, CONTROLS AND DISPLAYS.
HAND THROTTLE CONTROLS WERE NOT IDENTIFIED EITHER ON THE CONTROL KNOB OR ON THE INSTRUMENT PANEL AS REQUIRED BY FMVSS 101. CONSEQUENCE OF DEFECT: TRUCKS ARE NOT IN COMPLIANCE WITH FMVSS 101, CONTROLS AND DISPLAYS.
THE SEAT BELTS ON THE INVOLVED VEHICLES FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NOS. 208, OCCUPANT CRASH PROTECTION, AND 209, SEAT BELT ASSEMBLIES. THE NON-CONFORMITY EXISTS BECAUSE WHEN THE DRIVERS SEAT IS ADJUSTED TO THE FULL FORWARD POSITION, THE SEAT CUSHION IS ADJUSTED TO MAXIMUM ELEVATION, AND THE SEAT BACK IS TILTED TO THE FULLY UPRIGHT POSITION, THE SEAT BELTS ARE NOT LONG ENOUGH TO ACCOMMODATE SOME DRIVERS.
THE SEAT BELTS ON THE INVOLVED VEHICLES FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NOS. 208, OCCUPANT CRASH PROTECTION, AND 209, SEAT BELT ASSEMBLIES. THE NON-CONFORMITY EXISTS BECAUSE WHEN THE DRIVERS SEAT IS ADJUSTED TO THE FULL FORWARD POSITION, THE SEAT CUSHION IS ADJUSTED TO MAXIMUM ELEVATION, AND THE SEAT BACK IS TILTED TO THE FULLY UPRIGHT POSITION, THE SEAT BELTS ARE NOT LONG ENOUGH TO ACCOMMODATE SOME DRIVERS.
THE SEAT BELTS ON THE INVOLVED VEHICLES FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NOS. 208, OCCUPANT CRASH PROTECTION, AND 209, SEAT BELT ASSEMBLIES. THE NON-CONFORMITY EXISTS BECAUSE WHEN THE DRIVERS SEAT IS ADJUSTED TO THE FULL FORWARD POSITION, THE SEAT CUSHION IS ADJUSTED TO MAXIMUM ELEVATION, AND THE SEAT BACK IS TILTED TO THE FULLY UPRIGHT POSITION, THE SEAT BELTS ARE NOT LONG ENOUGH TO ACCOMMODATE SOME DRIVERS.
THE SEAT BELTS ON THE INVOLVED VEHICLES FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NOS. 208, OCCUPANT CRASH PROTECTION, AND 209, SEAT BELT ASSEMBLIES. THE NON-CONFORMITY EXISTS BECAUSE WHEN THE DRIVERS SEAT IS ADJUSTED TO THE FULL FORWARD POSITION, THE SEAT CUSHION IS ADJUSTED TO MAXIMUM ELEVATION, AND THE SEAT BACK IS TILTED TO THE FULLY UPRIGHT POSITION, THE SEAT BELTS ARE NOT LONG ENOUGH TO ACCOMMODATE SOME DRIVERS.
THE SEAT BELTS ON THE INVOLVED VEHICLES FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NOS. 208, OCCUPANT CRASH PROTECTION, AND 209, SEAT BELT ASSEMBLIES. THE NON-CONFORMITY EXISTS BECAUSE WHEN THE DRIVERS SEAT IS ADJUSTED TO THE FULL FORWARD POSITION, THE SEAT CUSHION IS ADJUSTED TO MAXIMUM ELEVATION, AND THE SEAT BACK IS TILTED TO THE FULLY UPRIGHT POSITION, THE SEAT BELTS ARE NOT LONG ENOUGH TO ACCOMMODATE SOME DRIVERS.
THE SEAT BELTS ON THE INVOLVED VEHICLES FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NOS. 208, OCCUPANT CRASH PROTECTION, AND 209, SEAT BELT ASSEMBLIES. THE NON-CONFORMITY EXISTS BECAUSE WHEN THE DRIVERS SEAT IS ADJUSTED TO THE FULL FORWARD POSITION, THE SEAT CUSHION IS ADJUSTED TO MAXIMUM ELEVATION, AND THE SEAT BACK IS TILTED TO THE FULLY UPRIGHT POSITION, THE SEAT BELTS ARE NOT LONG ENOUGH TO ACCOMMODATE SOME DRIVERS.
THE SEAT BELTS ON THE INVOLVED VEHICLES FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NOS. 208, OCCUPANT CRASH PROTECTION, AND 209, SEAT BELT ASSEMBLIES. THE NON-CONFORMITY EXISTS BECAUSE WHEN THE DRIVERS SEAT IS ADJUSTED TO THE FULL FORWARD POSITION, THE SEAT CUSHION IS ADJUSTED TO MAXIMUM ELEVATION, AND THE SEAT BACK IS TILTED TO THE FULLY UPRIGHT POSITION, THE SEAT BELTS ARE NOT LONG ENOUGH TO ACCOMMODATE SOME DRIVERS.
