Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.
CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.
EQUIPMENT DESCRIPTION: AFTERMARKET BRAKE ROTORS FOR USE ON CERTAIN FORD AND MAZDA TRUCKS. CRACKED CASTINGS CAUSED CRACKS TO APPEAR ON THE OUTER DIAMETER OF THE ROTOR HAT OR AROUND THE STUD HOLE.
WHEN THE AUTOMATIC TRANSMISSION SHIFT LEVER IS PLACED IN THE PARK POSITION, THE PARK PAWL DOES NOT ALWAYS ABUT OR ENGAGE THE PARK GEAR.
FRONT WHEEL BEARING ADJUSTING NUT RETAINING KEYS MAY BE MISSING FROM FRONT AXLE ASSEMBLIES, ALLOWING THE NUT TO LOOSEN.
WIRING FOR THE POWER LUMBAR SEAT SYSTEM WAS ROUTED DIRECTLY BENEATH THE SEAT CUSHION SPRINGS AND MAY BE ABRADED BY THE SPRINGS.
SPRING LOCK FUEL LINE COUPLING MAY NOT BE PROPERLY ENGAGED.
SPRING LOCK FUEL LINE COUPLING MAY NOT BE PROPERLY ENGAGED.
STICKERS CONCERNING HANDLING AND MANEUVERABILITY WHICH ARE AFFIXED TO DRIVERS SUN VISOR SLEEVES DO NOT MEET CRITERIA FOR PERMANENT ADHESION.
ALUMINUM WHEELS MAY HAVE BEEN INSTALLED WITH IMPROPER LUG NUTS.
NYLON FUEL LINES ON THE FUEL RETURN SIDE OF THE FUEL PRESSURE REGULATOR ASSEMBLY MAY CRACK. CONSEQUENCE OF DEFECT: FUEL LINE COULD LEAK AND, IF AN IGNITION SOURCE IS PRESENT, CREATE THE POTENTIAL FOR A FIRE.
THE ELECTRONIC ENGINE CONTROL WIRING HARNESS INSULATION MAY BE DAMAGED DUE TO COPPER SPIKES PRODUCED DURING THE WELDING OF ITS WIRES. THIS CREATES A POTENTIAL FOR A SHORT CIRCUIT BETWEEN THE WIRES WHICH ENERGIZE THE FUEL PUMP, CAUSING SOME FUEL INJECTORS TO OPEN, DISCHARGING FUEL INTO THE ENGINE. CONSEQUENCE OF DEFECT: FUEL DISCHARGED INTO THE ENGINE WOULD EVENTUALLY LEAK THROUGH THE EXHAUST SYSTEM TO THE GROUND. THIS COULD RESULT IN A FIRE IF A SOURCE OF IGNITION IS PRESENT.
COMPONENTS IN THE LOCKING HUBS WERE IMPROPERLY HEAT-TREATED AND MAY CRACK OR FRACTURE UPON ENGAGEMENT OF THE FRONT DRIVE AXLES. THE BROKEN COMPONENT ON THE LEFT FRONT WHEEL MAY BECOME JAMMED AGAINST THE NUT.
THE BOLTS THAT ATTACH THE D-SHAPED RING FOR THE SHOULDER BELT ARE INADEQUATELY SUPPORTED BY THE MATERIAL IN WHICH THEY ARE MOUNTED. THE ATTACHMENT DOES NOT COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 210, SEAT BELT ASSEMBLY ANCHORAGES.
