Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
INTERCONTINENTAL AUTO PARTS IS RECALLING 1,937 FUEL FILTERS, P/NOS ALG 44/1 AND PUROLATOR F10024, SHIPPED BETWEEN JANUARY 14 AND FEBRUARY 13, 2008, SOLD FOR USE ON THE VEHICLES LISTED ABOVE. THE FILTER'S OUTLET CAP MAY NOT BE SECURELY CRIMPED TO THE HOUSING. THIS COULD RESULT IN A SEPARATION OF FILTER'S OUTLET CAP FROM THE HOUSING.
CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.
CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.
CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.
CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.
CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.
CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.
CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.
CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.
THE SHIFT INDICATOR MAY NOT ACCURATELY REFLECT THE SHIFT SELECTOR POSITION. SOME VEHICLES WERE PRODUCED WITH TRANSMISSION CONTROL SELECTOR TUBE RETAINING CLIPS THAT MAY NOT BE HARD ENOUGH. THE CLIP MAY LOOSEN OR FALL OFF, AND THE SELECTOR TUBE MAY BECOME DISPLACED.
THE PARK LEVER ON THE INVOLVED VEHICLES CONTAINS A DEFECTIVE SPRING WHICH COULD PREVENT AUTOMATIC ENGAGEMENT OF THE PARKING GEAR.
THE PARK LEVER ON THE INVOLVED VEHICLES CONTAINS A DEFECTIVE SPRING WHICH COULD PREVENT AUTOMATIC ENGAGEMENT OF THE PARKING GEAR.
ON SOME OF THE INVOLVED VEHICLES, THE BRAKE PUSHROD TO BRAKE PEDAL RETAINING PINS MAY BE MISSING OR LOOSE. INSECURELY INSTALLED OR MISSING RETAINERS COULD RESULT IN DISENGAGEMENT OF THE BRAKE PUSHROD AND TOTAL LOSS OF SERVICE BRAKING.
WINDSHIELDS MAY HAVE BEEN INSTALLED ON THESE VEHICLES WITHOUT THE APPLICATION OF A BUTYL PRIMER ON THE MOUNTING SURFACE OF THE GLAZING. THE PRIMER IS REQUIRED TO ENSURE ADEQUATE RETENTION OF THE WINDSHIELD TO ITS OPENING FLANGE. THIS CONSTITUTES A NON-COMPLIANCE WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 212, WINDSHIELD MOUNTING.
THE INVOLVED VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 105, HYDRAULIC BRAKE SYSTEMS. REAR AXLE ASSEMBLIES INTENDED FOR OTHER VEHICLES MAY HAVE BEEN INSTALLED IN THE INVOLVED VEHICLES. THE WHEEL CYLINDERS MAY NOT BE THE CORRECT SIZE. THIS COULD AFFECT BRAKING PERFORMANCE.
THE INVOLVED VEHICLES WERE PRODUCED WITH BRAKE PUSH-ROD TO BRAKE PEDAL RETAINING PINS WHICH WERE NOT HEAT-TREATED AS SPECIFIED. THIS COULD ALLOW THE BRAKE PEDAL TO BECOME DISENGAGED FROM THE PUSH-ROD.
THE INVOLVED VEHICLES WERE BUILT WITH SAFETY COMPLIANCE CERTIFICATION LABELS THAT CONTAINED INCORRECT GVWR AND GAWR WEIGHT INFORMATION. THE GVWRS COULD BE OVERSTATED BY UP TO 197 LBS., DUE TO AN ERROR IN THE REPORTING OF INCREMENTAL OPTION WEIGHTS USED TO DERIVE THE GVWRS AND GAWRS.
THE INVOLVED VEHICLES CONTAIN EMISSION CONTROL SYSTEMS THAT UTILIZE A PULSE AIR REED VALVE TO PERMIT AIR FLOW FROM THE AIR CLEANER TO THE EXHAUST MANIFOLD ON NEGATIVE PRESSURE PULSATIONS. THESE REED VALVES MAY FAIL UNDER COLD WEATHER CONDITIONS, CAUSING A BACKFLOW OF EXHAUST GAS INTO THE AIR CLEANER AND FUEL INDUCTION SYSTEM ON POSITIVE EXHAUST PULSES. THIS CAUSES AN OVERLY RICH AIR/FUEL MIXTURE, REDUCED FUEL ECONOMY AND REDUCED ENGINE PERFORMANCE. CONTINUED VEHICLE OPERATION MAY RESULT IN ENGINE STALLING OR OVERHEATING OF THE EXHAUST SYSTEM.
THE WINDSHIELD WIPER DRIVE LINKAGE ON THE AFFECTED VEHICLES MAY FRACTURE DUE TO METAL FATIGUE AS A RESULT OF REPEATED FLEXING OF THE DRIVE ARM ACROSS A STRESS SENSITIVE AREA. THIS CONDITION WILL RENDER THE WINDSHIELD WIPER SYSTEM INOPERATIVE.
AN IMPROPER TRANSMISSION SHIFT BRACKET WAS INSTALLED WHICH, BECAUSE OF ITS DESIGN, COULD CONTACT AND ABRADE THE FUEL HOSE. FUEL LEAKAGE AND POSSIBLE ACCUMULATION OF FUEL ON A SURFACE BENEATH A PARKED VEHICLE COULD RESULT.
TRANSMISSION SHIFT CONTROL RODS WERE INSTALLED THAT WERE INTENDED FOR USE WITH THE STEERING COLUMNS OF A PRIOR DESIGN LEVEL. ATTACHMENT OF THE SHIFT CONTROL ROD WITH THE STEERING COLUMN SHIFT LEVER GROMMET WILL ALLOW RELATIVE MOVEMENT BETWEEN THESE PARTS. CONTINUED USAGE COULD RESULT IN GROMMET WEAR AND DETERIORATION OF THE SHIFT CONTROL FUNCTION, WITH THE POTENTIAL FOR STARTING IN GEAR OR AN INABILITY TO ENGAGE THE PARKING GEAR.
BECAUSE OF ITS POSITION, THE WIRING ASSEMBLY MAY CHAFE AGAINST THE COWL-TO-BRAKE PEDAL SUPPORT BRACE WHICH IS LOCATED UNDER THE INSTRUMENT PANEL.
THE INVOLVED VEHICLES ARE EQUIPPED WITH AIR CONDITIONING UNITS WHICH CONTAIN BLOWER MOTOR RESISTOR WIRES WHICH ARE IMPROPERLY POSITIONED. AS A RESULT, UNDER CERTAIN CONDITIONS THE POLYPROPYLENE CASE MATERIAL COULD BECOME OVERHEATED AND EVENTUALLY IGNITE, ESPECIALLY IF THE BLOWER MOTOR SWITCH IS IN THE LOW OR MEDIUM POSITION.
ON SOME OF THE INVOLVED VEHICLES, THE TRANSMISSION PARKING PAWL MAY NOT ENGAGE THE PARKING GEAR WHEN THE TRANSMISSION SELECTOR LEVER IS PLACED IN THE PARK POSITION. THIS CONDITION IS ATTRIBUTABLE TO EXCESSIVE FREE PLAY IN THE TRANSMISSION SHIFT LINKAGE ADJUSTMENT.
THE INVOLVED VEHICLES MAY BE IN NON-COMPLIANCE TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 105, HYDRAULIC BRAKE SYSTEMS, DUE TO INSTALLATION OF INCORRECT REAR AXLE ASSEMBLIES. CONSEQUENTLY, EARLY REAR WHEEL LOCK-UP UNDER LIGHT LOADING CONDITIONS COULD RESULT CAUSING VEHICLE DIRECTIONAL INSTABILITY. REAR BRAKING EFFECTIVENESS WOULD ALSO BE REDUCED.
THE INVOLVED VEHICLES MAY HAVE BEEN INCORRECTLY EQUIPPED WITH MANUAL BRAKES INSTEAD OF POWER BRAKES. CONSEQUENTLY, A NON-COMPLIANCE TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 105, HYDRAULIC BRAKE SYSTEMS, MAY EXIST.
THE FRONT DISC BRAKE ROTORS INSTALLED ON THE INVOLVED VEHICLES MAY HAVE BEEN IMPROPERLY MANUFACTURED SO THAT THEY CONTAIN CRACKS. THESE CRACKED ROTORS COULD FRACTURE DURING VEHICLE BRAKING AND CAUSE BRAKE PULL AND AFFECT VEHICLE DIRECTIONAL CONTROL.
