Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
IN A REAR END COLLISION, THE PICKUP BOX CROSSMEMBER COULD CONTACT THE FUEL PUMP MODULES FUEL LINE, CAUSING A FUEL LEAK WHICH WOULD BE IN NON-COMPLIANCE WITH FMVSS 301.
IN A REAR END COLLISION, THE PICKUP BOX CROSSMEMBER COULD CONTACT THE FUEL PUMP MODULES FUEL LINE, CAUSING A FUEL LEAK WHICH WOULD BE IN NON-COMPLIANCE WITH FMVSS 301.
IN A REAR END COLLISION, THE PICKUP BOX CROSSMEMBER COULD CONTACT THE FUEL PUMP MODULES FUEL LINE, CAUSING A FUEL LEAK WHICH WOULD BE IN NON-COMPLIANCE WITH FMVSS 301.
IN A REAR END COLLISION, THE PICKUP BOX CROSSMEMBER COULD CONTACT THE FUEL PUMP MODULES FUEL LINE, CAUSING A FUEL LEAK WHICH WOULD BE IN NON-COMPLIANCE WITH FMVSS 301.
AUTOMATIC TRANSMISSION MAY CONTAIN A PARK SPRAG ROD ASSEMBLY THAT MAY STICK IN THE TOOTH BUTT UNENGAGED POSITION.
PLASTIC HYDRAULIC CLUTCH SYSTEM COMPONENTS ARE SUBJECT TO EXHAUST SYSTEM HEAT DAMAGE DUE TO PROLONGED COLD, HIGH SPEED IDLE OPERATION.
DUE TO IMPROPER MATERIAL CONSTRUCTION THE HYDRO-BOOST FLUID RETURN HOSE MAY NOT BE CAPABLE OF WITHSTANDING THE TEMPERATURES AND/OR PRESSURES EXPERIENCED WITH THE HYDRO-BOOST SYSTEM. ALSO, THE HYDRO-BOOST FLUID HIGH PRESSURE HOSE ASSEMBLY MAY HAVE BEEN MISLOCATED, ALLOWING THE ASSEMBLY TO CONTACT THE FRAME SIDE RAIL. ABRASION RESULTING FROM CONTINUED CONTACT ALONG WITH IMPROPER MATERIAL CONSTRUCTION MAY CAUSE PRESSURE HOSE FAILURE. EITHER OF THESE CONDITIONS MAY CAUSE HYDRO-BOOST FLUID LEAKAGE, RESULTING IN THE LOSS OF POWER ASSIST FOR THE STEERING AND BRAKING SYSTEMS. COMPLETE LOSS OF STEERING OR BRAKING WILL NOT OCCUR SINCE BOTH SYSTEMS WOULD REVERT TO MANUAL OPERATION.
IMPROPER ROUTING OF THE HYDROBOOST HYDRAULIC SYSTEM HIGH PRESSURE HOSE ASSEMBLY COULD ALLOW A TUBULAR SECTION TO CONTACT THE FRAME SIDE RAIL. ABRASION FROM THE CONTACT COULD RESULT, CAUSING A LEAK IN THE HOSE ASSEMBLY.
AN INTERMEDIATE STEERING SHAFT CONTAINING A MISMATCHED POT COUPLING ASSEMBLY MAY HAVE BEEN INSTALLED ON THE INVOLVED VEHICLES. THIS COUPLING MAY HAVE AN OVERSIZED SERRATION DIAMETER. AN OVERSIZED SERRATION COULD PREVENT THE COUPLING FROM ADEQUATELY TIGHTENING ONTO THE GEAR OR SHAFT SPLINES.
THE FUEL TUBES (FUEL TANK TO PUMP) ON THE INVOLVED VEHICLES MAY BE ROUTED SUCH THAT TUBE TO UNDERBODY REINFORCEMENT FLANGE INTERFERENCE MAY RESULT DURING VEHICLE OPERATION. TUBE ABRASION CAUSED BY SUCH INTERFERENCE MAY RESULT IN FUEL LEAKAGE.
THE FUEL TUBES (FUEL TANK TO PUMP) ON THE INVOLVED VEHICLES MAY BE ROUTED SUCH THAT TUBE TO UNDERBODY REINFORCEMENT FLANGE INTERFERENCE MAY RESULT DURING VEHICLE OPERATION. TUBE ABRASION CAUSED BY SUCH INTERFERENCE MAY RESULT IN FUEL LEAKAGE.
