Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
THE HEATER CONTROL VALVE STEM DOES NOT MEET THE MATERIAL SPECIFICATIONS. HIGH COOLANT TEMPERATURES CAN CAUSE THE STEM TO LEAK.
THE HEATER CONTROL VALVE STEM DOES NOT MEET THE MATERIAL SPECIFICATIONS. HIGH COOLANT TEMPERATURES CAN CAUSE THE STEM TO LEAK.
IN SOME VEHICLES, THE MANUFACTURER'S PROTECTIVE INTERNAL COATING OF THE ELECTRONIC CRANK ANGLE SENSOR DOES NOT MEET SPECIFICATIONS, WHICH CAN CAUSE AN OPEN CIRCUIT AT HIGH OPERATING TEMPERATURES. THIS CAN CAUSE THE VEHICLE TO STALL.
THE VEHICLES FAILED THE LATERAL MOVING BARRIER IMPACT TEST REQUIREMENTS OF FMVSS 301, FUEL SYSTEM INTEGRITY. THE FUEL LEAKAGE FROM THE GAS TANK EXCEEDED THE MAXIMUM ALLOWABLE AMOUNT OF SPILLAGE.
THE VEHICLES FAILED THE LATERAL MOVING BARRIER IMPACT TEST REQUIREMENTS OF FMVSS 301, FUEL SYSTEM INTEGRITY. THE FUEL LEAKAGE FROM THE GAS TANK EXCEEDED THE MAXIMUM ALLOWABLE AMOUNT OF SPILLAGE.
THE VEHICLES FAILED THE LATERAL MOVING BARRIER IMPACT TEST REQUIREMENTS OF FMVSS 301, FUEL SYSTEM INTEGRITY. THE FUEL LEAKAGE FROM THE GAS TANK EXCEEDED THE MAXIMUM ALLOWABLE AMOUNT OF SPILLAGE.
THE VEHICLES FAILED THE LATERAL MOVING BARRIER IMPACT TEST REQUIREMENTS OF FMVSS 301, FUEL SYSTEM INTEGRITY. THE FUEL LEAKAGE FROM THE GAS TANK EXCEEDED THE MAXIMUM ALLOWABLE AMOUNT OF SPILLAGE.
THE VEHICLES FAILED THE LATERAL MOVING BARRIER IMPACT TEST REQUIREMENTS OF FMVSS 301, FUEL SYSTEM INTEGRITY. THE FUEL LEAKAGE FROM THE GAS TANK EXCEEDED THE MAXIMUM ALLOWABLE AMOUNT OF SPILLAGE.
THE MANUAL TRANSMISSIONS MAY LOCK UP FROM INSUFFICIENT LUBRICATION OF THE GEARS IN THE TRANSMISSION CASE. THIS CAN CAUSE THE DRIVE WHEELS TO SEIZE AND THE VEHICLE TO COME TO A SUDDEN STOP.
THE MANUAL TRANSMISSIONS MAY LOCK UP FROM INSUFFICIENT LUBRICATION OF THE GEARS IN THE TRANSMISSION CASE. THIS CAN CAUSE THE DRIVE WHEELS TO SEIZE AND THE VEHICLE TO COME TO A SUDDEN STOP.
THE MANUAL TRANSMISSIONS MAY LOCK UP FROM INSUFFICIENT LUBRICATION OF THE GEARS IN THE TRANSMISSION CASE. THIS CAN CAUSE THE DRIVE WHEELS TO SEIZE AND THE VEHICLE TO COME TO A SUDDEN STOP.
THE MANUAL TRANSMISSIONS MAY LOCK UP FROM INSUFFICIENT LUBRICATION OF THE GEARS IN THE TRANSMISSION CASE. THIS CAN CAUSE THE DRIVE WHEELS TO SEIZE AND THE VEHICLE TO COME TO A SUDDEN STOP.
DETERIORATION OF THE REED VALVE SUBASSEMBLY MAY LEAD TO A MALFUNCTION WITHIN THE SECONDARY AIR SUPPLY PORTION OF THE EMISSION CONTROL SYSTEM. THE SCREWS WHICH ATTACH THE REEDS TO THE REED VALVE SUBASSEMBLY MAY RUST, AND IF THE RUSTING BECOMES SEVERE, THE SCREW HEADS WILL ERODE AND ALLOW THE REEDS TO SEPARATE FROM THE REED VALVE SUBASSEMBLY. CORROSION MAY ALSO OCCUR ON THE REED VALVE SUBASSEMBLY, DEFORMING THE REED SEATS AND PREVENTING THE REEDS FROM CLOSING PROPERLY. SEPARATION OF THE REEDS FROM THE REED VALVE SUBASSEMBLY OR IMPROPER CLOSING OF THE REEDS ALLOW HOT EXHAUST GASES TO FLOW BACKWARD INTO THE PLASTIC SECONDARY AIR FILTER CASE WHEN THE VEHICLE IS BEING DRIVEN. THESE HOT EXHAUST GASES MAY MELT THE SECONDARY PLASTIC AIR FILTER CASE.
DETERIORATION OF THE REED VALVE SUBASSEMBLY MAY LEAD TO A MALFUNCTION WITHIN THE SECONDARY AIR SUPPLY PORTION OF THE EMISSION CONTROL SYSTEM. THE SCREWS WHICH ATTACH THE REEDS TO THE REED VALVE SUBASSEMBLY MAY RUST, AND IF THE RUSTING BECOMES SEVERE, THE SCREW HEADS WILL ERODE AND ALLOW THE REEDS TO SEPARATE FROM THE REED VALVE SUBASSEMBLY. CORROSION MAY ALSO OCCUR ON THE REED VALVE SUBASSEMBLY, DEFORMING THE REED SEATS AND PREVENTING THE REEDS FROM CLOSING PROPERLY. SEPARATION OF THE REEDS FROM THE REED VALVE SUBASSEMBLY OR IMPROPER CLOSING OF THE REEDS ALLOW HOT EXHAUST GASES TO FLOW BACKWARD INTO THE PLASTIC SECONDARY AIR FILTER CASE WHEN THE VEHICLE IS BEING DRIVEN. THESE HOT EXHAUST GASES MAY MELT THE SECONDARY PLASTIC AIR FILTER CASE.
DETERIORATION OF THE REED VALVE SUBASSEMBLY MAY LEAD TO A MALFUNCTION WITHIN THE SECONDARY AIR SUPPLY PORTION OF THE EMISSION CONTROL SYSTEM. THE SCREWS WHICH ATTACH THE REEDS TO THE REED VALVE SUBASSEMBLY MAY RUST, AND IF THE RUSTING BECOMES SEVERE, THE SCREW HEADS WILL ERODE AND ALLOW THE REEDS TO SEPARATE FROM THE REED VALVE SUBASSEMBLY. CORROSION MAY ALSO OCCUR ON THE REED VALVE SUBASSEMBLY, DEFORMING THE REED SEATS AND PREVENTING THE REEDS FROM CLOSING PROPERLY. SEPARATION OF THE REEDS FROM THE REED VALVE SUBASSEMBLY OR IMPROPER CLOSING OF THE REEDS ALLOW HOT EXHAUST GASES TO FLOW BACKWARD INTO THE PLASTIC SECONDARY AIR FILTER CASE WHEN THE VEHICLE IS BEING DRIVEN. THESE HOT EXHAUST GASES MAY MELT THE SECONDARY PLASTIC AIR FILTER CASE.
DETERIORATION OF THE REED VALVE SUBASSEMBLY MAY LEAD TO A MALFUNCTION WITHIN THE SECONDARY AIR SUPPLY PORTION OF THE EMISSION CONTROL SYSTEM. THE SCREWS WHICH ATTACH THE REEDS TO THE REED VALVE SUBASSEMBLY MAY RUST, AND IF THE RUSTING BECOMES SEVERE, THE SCREW HEADS WILL ERODE AND ALLOW THE REEDS TO SEPARATE FROM THE REED VALVE SUBASSEMBLY. CORROSION MAY ALSO OCCUR ON THE REED VALVE SUBASSEMBLY, DEFORMING THE REED SEATS AND PREVENTING THE REEDS FROM CLOSING PROPERLY. SEPARATION OF THE REEDS FROM THE REED VALVE SUBASSEMBLY OR IMPROPER CLOSING OF THE REEDS ALLOW HOT EXHAUST GASES TO FLOW BACKWARD INTO THE PLASTIC SECONDARY AIR FILTER CASE WHEN THE VEHICLE IS BEING DRIVEN. THESE HOT EXHAUST GASES MAY MELT THE SECONDARY PLASTIC AIR FILTER CASE.
LOCK WASHER LOCATED UNDER THE NUT THAT SECURES THE FRONT HUB TO THE DRIVE SHAFT MAY HAVE HAD IMPROPER HEAT TREATMENT AND COULD CRACK.
IF CRUISE CONTROL MAIN SWITCH IS IN THE ON POSITION WHEN ENGINE IS STARTED, SYSTEM CAN BE AFFECTED BY A SHORT DURATION VOLTAGE DROP CAUSED BY OPTIONAL HI-POWER (H340) RADIO.
IF CRUISE CONTROL MAIN SWITCH IS IN THE ON POSITION WHEN ENGINE IS STARTED, SYSTEM CAN BE AFFECTED BY A SHORT DURATION VOLTAGE DROP CAUSED BY OPTIONAL HI-POWER (H340) RADIO.
IF CRUISE CONTROL MAIN SWITCH IS IN THE ON POSITION WHEN ENGINE IS STARTED, SYSTEM CAN BE AFFECTED BY A SHORT DURATION VOLTAGE DROP CAUSED BY OPTIONAL HI-POWER (H340) RADIO.
IF CRUISE CONTROL MAIN SWITCH IS IN THE ON POSITION WHEN ENGINE IS STARTED, SYSTEM CAN BE AFFECTED BY A SHORT DURATION VOLTAGE DROP CAUSED BY OPTIONAL HI-POWER (H340) RADIO.
VEHICLE MAY FAIL TO CONFORM TO THE BRAKE FADE AND RECOVERY PORTION OF FMVSS 105.
VEHICLE MAY FAIL TO CONFORM TO THE BRAKE FADE AND RECOVERY PORTION OF FMVSS 105.
A COTTER PIN IN THE BRAKE PEDAL TO BRAKE MASTER CYLINDER LINKAGE ASSEMBLY MAY BE MISSING. THIS PIN ACTS AS A RETAINER FOR THE BRAKE MASTER CYLINDER PUSHROD CLEVIS PIN. CONSEQUENCE OF DEFECT: THE CLEVIS PIN MAY SLIDE OUT CAUSING THE MASTER CYLINDER/BRAKE PEDAL LINKAGE TO BECOME DISENGAGED. IF THIS LINKAGE BECOMES DISENGAGED THE SERVICE BRAKES CANNOT BE APPLIED, CREATING THE RISK OF A CRASH WITHOUT PRIOR WARNING.
