Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
THE FUEL LINES ON THESE VEHICLES MAY HAVE BEEN MISROUTED AND MAY CONTACT THE AIR CHECK VALVE. THE HIGH TEMPERATURES FROM THE AIR CHECK VALVE COULD ALLOW IT TO MELT THROUGH AND DAMAGE A FUEL LINE.
VEHICLE DESCRIPTION: PASSENGER VEHICLES. DURING VERY COLD WEATHER, WATER THATN ENTERS THE ACCELERATOR CONTROL CABLE CONDUIT FREEZES AND CAUSES THE ACCELERATOR CABLE TO DEVELOP A HIGH EFFORT OR BINDING CONDITION.
VEHICLE DESCRIPTION: PASSENGER VEHICLES. DURING VERY COLD WEATHER, WATER THATN ENTERS THE ACCELERATOR CONTROL CABLE CONDUIT FREEZES AND CAUSES THE ACCELERATOR CABLE TO DEVELOP A HIGH EFFORT OR BINDING CONDITION.
THE SAFETY BELT BUCKLE ASSEMBLIES MAY NOT LATCH OR MAY NOT RELEASE DUE TO THE FRACTURE OF THE RED RELEASE PUSH BUTTON.
THE SAFETY BELT BUCKLE ASSEMBLIES MAY NOT LATCH OR MAY NOT RELEASE DUE TO THE FRACTURE OF THE RED RELEASE PUSH BUTTON.
THE SAFETY BELT BUCKLE ASSEMBLIES MAY NOT LATCH OR MAY NOT RELEASE DUE TO THE FRACTURE OF THE RED RELEASE PUSH BUTTON.
THE SAFETY BELT BUCKLE ASSEMBLIES MAY NOT LATCH OR MAY NOT RELEASE DUE TO THE FRACTURE OF THE RED RELEASE PUSH BUTTON.
THE NEUTRAL START SAFETY SWITCH COULD HAVE BEEN FRACTURED DURING INSTALLATION.
THE BRAKE HOSES WERE MANUFACTURED INCORRECTLY, AND DO NOT COMPLY WITH FMVSS 106, BRAKE HOSES.
THE DRIVER AND PASSENGER FRONT SEAT MANUAL RECLINING MECHANISMS DO NOT COMPLY WITH THE REQUIREMENTS OF FMVSS 207, SEATING SYSTEMS. THE SEAT BACK MECHANISMS WILL NOT LATCH UNDER CERTAIN CONDITIONS.
THE FOG LAMPS, LOW BEAM HEADLAMPS, AND HIGH BEAM HEADLAMPS CAN BE OPERATED SIMULTANEOUSLY. THIS CAN CAUSE THE HEADLAMP CIRCUIT BREAKER TO OVERLOAD AND TRIP, RESULTING IN LOSS OF HEADLAMPS (LOW AND HIGH BEAM) AND FOG LIGHTS.
THE AUTOMATIC TRANSMISSION SHIFT CONTROL CABLE CAN SEPARATE.
FRONT FUEL FEED HOSE ASSEMBLY COULD CRACK OR SEPARATE AT THE COUPLING ON THE ENGINE END OF THE HOSE ASSEMBLY, ALLOWING FUEL TO LEAK INTO THE ENGINE COMPARTMENT.
FRONT FUEL FEED HOSE ASSEMBLY COULD CRACK OR SEPARATE AT THE COUPLING ON THE ENGINE END OF THE HOSE ASSEMBLY, ALLOWING FUEL TO LEAK INTO THE ENGINE COMPARTMENT.
THE POWER SEAT OR RECLINER WIRING HARNESS CAN BE PINCHED OR CAN CHAFE ON THE SEAT FRAME OR SPRING SUPPORT ROD, WEARING THROUGH THE WIRE INSULATION AND CAUSING AN ELECTRICAL SHORT.
THE POWER SEAT OR RECLINER WIRING HARNESS CAN BE PINCHED OR CAN CHAFE ON THE SEAT FRAME OR SPRING SUPPORT ROD, WEARING THROUGH THE WIRE INSULATION AND CAUSING AN ELECTRICAL SHORT.
THE VEHICLES WERE ASSEMBLED WITH AN INCORRECT SUSPENSION UPPER SPRING SEAT AT THE RIGHT-REAR POSITION. IF THE VEHICLE IS INVOLVED IN A REAR IMPACT ACCIDENT, THE RIGHT-HAND REAR WHEEL HOUSE FLANGE COULD SEVER THE FUEL TANK FILLER PIPE AND SPILL FUEL.
BRAKE STOPLAMPS MAY NOT ILLUMINATE OR, IN SOME CASES, STOPLAMPS MAY NOT STAY ILLUMINATED ALL THE TIME WHEN BRAKES ARE APPLIED DUE TO A FAULTY STOPLAMP SWITCH. ALSO, IN VEHICLES WITH CRUISE CONTROL, A FAULTY STOPLAMP SWITCH CAN RESULT IN RESUMPTION OF THE CRUISE CONTROL FUNCTION UPON RELEASE OF THE BRAKE PEDAL.
BRAKE STOPLAMPS MAY NOT ILLUMINATE OR, IN SOME CASES, STOPLAMPS MAY NOT STAY ILLUMINATED ALL THE TIME WHEN BRAKES ARE APPLIED DUE TO A FAULTY STOPLAMP SWITCH. ALSO, IN VEHICLES WITH CRUISE CONTROL, A FAULTY STOPLAMP SWITCH CAN RESULT IN RESUMPTION OF THE CRUISE CONTROL FUNCTION UPON RELEASE OF THE BRAKE PEDAL.
THE ACCELERATOR CABLE MAY HAVE BEEN KINKED DURING VEHICLE ASSEMBLY. THE KINK IN THE CABLE CAN CAUSE EITHER A HIGH EFFORT ACCELERATOR CABLE, STICKING ACCELERATOR CABLE, OR A BROKEN ACCELERATOR CABLE.
MOISTURE CAN ENTER THE EXPRESS-DOWN ELECTRONIC CONTROL MODULE AND CAUSE A SHORT CIRCUIT THAT CAUSES WINDOW OPERATION WITHOUT OPERATOR CONTROL, AND LEAVES THE WINDOW IN THE DOWN POSITION.
THE GLOVE COMPARTMENT DOOR WILL NOT REMAIN CLOSED DURING CERTAIN LOAD FORCES ASSOCIATED WITH A VEHICLE CRASH. THIS DOES NOT COMPLY WITH THE REQUIREMENTS OF FMVSS 201.
THE GLOVE COMPARTMENT DOOR WILL NOT REMAIN CLOSED DURING CERTAIN LOAD FORCES ASSOCIATED WITH A VEHICLE CRASH. THIS DOES NOT COMPLY WITH THE REQUIREMENTS OF FMVSS 201.
THE FRONT DOOR SHOULDER BELT GUIDE LOOPS MAY BE CRACKED AND ARE NOT IN COMPLIANCE WITH FMVSS 208.
THE FRONT DOOR SHOULDER BELT GUIDE LOOPS MAY BE CRACKED AND ARE NOT IN COMPLIANCE WITH FMVSS 208.
THE REVERSE SERVO APPLY PIN MAY BIND IN THE CASE WHICH COULD CAUSE REVERSE BAND DISTRESS (LOSS OR SLIPPING OF REVERSE), REVERSE BAND DRAG IN DRIVE RANGE (POOR PERFORMANCE -- POOR POWER), OR THE TRANSMISSION TO REMAIN IN REVERSE WHILE THE SHIFT INDICATOR SHOWS NEUTRAL GEAR POSITION.
THE BOLTS AND NUTS WHICH ATTACH THE BEARING-HUB ASSEMBLY TO THE REAR AXLE FLANGE ARE NOT SUFFICIENTLY TIGHTENED ON SOME VEHICLES.
THE CONSOLE MOUNTED SHIFT LEVER MAY DISENGAGE FROM THE SHIFT CONTROL CABLE BRACKET CAUSING LOSS OF GEAR INDICATOR REFERENCE AND SHIFT SELECTOR OPERATION.
THE PASSENGER'S SIDE EASY-ENTRY SEAT ADJUSTER MAY FAIL FULLY LOCK INTO POSITION AFTER THE SEAT BACK HAS BEEN TILTED FORWARD AND THE SEAT SLID FORWARD, THEN RETURNED TO ITS ORIGINAL POSTITION.
FRONT SHOULDER SAFETY BELT WEBBING MAY SEPARATE AT FRONT BELT UPPER GUIDE LOOPS ON EITHER SIDE OF THE FRONT SEAT.
