Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
THE ACCELERATOR CONTROL CABLE COULD HAVE BEEN KINKED DURING ASSEMBLY CAUSING HIGH ACCELERATOR PEDAL EFFORT, STICKING ACCELERATOR CONTROL CABLE, OR A BROKEN ACCELERATOR CONTROL CABLE.
THESE VEHICLES WERE ASSEMBLED WITH A MALFUNCTION ALARM, LIGHTING AND LOCKING (MALL) MODULE THAT CAN CONTAIN A DAMAGED CAPACITOR. IF THE CAPACITOR IS DAMAGED, THE KEY IN THE IGNITION WARNING CHIME AND THE DRIVER SEAT BELT UNBUCKLED WARNING CHIME AND INDICATOR LAMP MAY NOT WORK. THIS DOES NOT MEET THE REQUIREMENTS OF FMVSS NO. 114, THEFT PROTECTION AND FMVSS NO. 208, OCCUPANT CRASH PROTECTION. IN ADDITION, OTHER CHIME REMINDER FUNCTIONS, INTERIOR LIGHTING CONTROLS, AND POWER DOOR LOCKING FEATURES ARE ALSO AFFECTED.
THESE VEHICLES WERE ASSEMBLED WITH REAR OUTBOARD SAFETY BELT ANCHORAGES THAT MAY NOT WITHSTAND THE REQUIRED LOAD. THIS DOES NOT COMPLY WITH FMVSS NO.210, SEAT BELT ASSEMBLY ANCHORAGES.
THESE VEHICLES WERE ASSEMBLED WITH REAR OUTBOARD SAFETY BELT ANCHORAGES THAT MAY NOT WITHSTAND THE REQUIRED LOAD. THIS DOES NOT COMPLY WITH FMVSS NO.210, SEAT BELT ASSEMBLY ANCHORAGES.
THESE VEHICLES WERE ASSEMBLED WITH REAR OUTBOARD SAFETY BELT ANCHORAGES THAT MAY NOT WITHSTAND THE REQUIRED LOAD. THIS DOES NOT COMPLY WITH FMVSS NO.210, SEAT BELT ASSEMBLY ANCHORAGES.
SOME WELDS WERE OMITTED FROM THE BODY LOCK PILLAR, OR B PILLAR. THIS DOES NOT COMPLY WITH FMVSS NO.208, OCCUPANT CRASH PROTECTION.
CRACKS DEVELOP IN THE WHEEL MOUNTING SURFACE. IF THESE CRACKS BECOME SEVERE ENOUGH, THE WHEEL WILL COMPLETELY SEPARATE FROM THE VEHICLE.
CRACKS DEVELOP IN THE WHEEL MOUNTING SURFACE. IF THESE CRACKS BECOME SEVERE ENOUGH, THE WHEEL WILL COMPLETELY SEPARATE FROM THE VEHICLE.
CRACKS DEVELOP IN THE WHEEL MOUNTING SURFACE. IF THESE CRACKS BECOME SEVERE ENOUGH, THE WHEEL WILL COMPLETELY SEPARATE FROM THE VEHICLE.
CRACKS DEVELOP IN THE WHEEL MOUNTING SURFACE. IF THESE CRACKS BECOME SEVERE ENOUGH, THE WHEEL WILL COMPLETELY SEPARATE FROM THE VEHICLE.
CRACKS DEVELOP IN THE WHEEL MOUNTING SURFACE. IF THESE CRACKS BECOME SEVERE ENOUGH, THE WHEEL WILL COMPLETELY SEPARATE FROM THE VEHICLE.
CRACKS DEVELOP IN THE WHEEL MOUNTING SURFACE. IF THESE CRACKS BECOME SEVERE ENOUGH, THE WHEEL WILL COMPLETELY SEPARATE FROM THE VEHICLE.
THE STEERING INTERMEDIATE SHAFT COULD HAVE BEEN IMPROPERLY ASSEMBLED CAUSING THE SHAFT LOWER COUPLING TO LOOSEN AND ROTATE ON THE STEERING GEAR INPUT SHAFT.
IMPROPERLY MANUFACTURED BRAKE PEDAL ARM CAUSES THE BRAKE PEDAL ARM TO FRACTURE DURING BRAKING.
THESE VEHICLES HAVE BEEN BUILT WITH WELDS MISSING FROM THE FRONT SUSPENSION LOWER CONTROL ARM ASSEMBLIES CAUSING EXCESSIVE LOADS ON THE EXISTING WELDS.
INSUFFICIENT LUBRICATION IN THE GUIDE TRACK RAIL IN WHICH THE SHOULDER BELT CARRIER MOVES CAUSING A CHATTERING NOISE, MOMENTARY BINDING WHILE TRAVELING, CYCLING BACK AND FORTH, OR STOPS COMPLETELY.
INSUFFICIENT LUBRICATION IN THE GUIDE TRACK RAIL IN WHICH THE SHOULDER BELT CARRIER MOVES CAUSING A CHATTERING NOISE, MOMENTARY BINDING WHILE TRAVELING, CYCLING BACK AND FORTH, OR STOPS COMPLETELY.
INSUFFICIENT LUBRICATION IN THE GUIDE TRACK RAIL IN WHICH THE SHOULDER BELT CARRIER MOVES CAUSING A CHATTERING NOISE, MOMENTARY BINDING WHILE TRAVELING, CYCLING BACK AND FORTH, OR STOPS COMPLETELY.
INSUFFICIENT LUBRICATION IN THE GUIDE TRACK RAIL IN WHICH THE SHOULDER BELT CARRIER MOVES CAUSING A CHATTERING NOISE, MOMENTARY BINDING WHILE TRAVELING, CYCLING BACK AND FORTH, OR STOPS COMPLETELY.
THESE VEHICLES WERE ASSEMBLED WITH LIGHTING CONTROL MODULES WHICH CAN EXPERIENCE EXCESSIVE CURRENT LEAKAGE DUE TO DAMAGED SURFACE MOUNTING CAPACITORS. THIS CAN CAUSE LOSS OF HEAD LAMPS AND PARKING LAMPS.
THESE VEHICLES WERE CONSTRUCTED WITH WELDS IN THE REAR COMPARTMENT PAN ASSEMBLY THAT ARE NOT SUFFICIENT TO COMPLY WITH THE REQUIREMENTS PERTAINING TO FUEL TANK LEAKAGE IN THE EVENT OF A REAR IMPACT COLLISION. THE FUEL TANK ASSEMBLIES DO NOT COMPLY WITH FMVSS NO. 301, FUEL SYSTEM INTEGRITY.
THESE VEHICLES WERE BUILT WITH OVERTORQUED DRIVE AXLE SPINDLE NUTS. THIS CONDITION CAN CAUSE EXCESSIVE LOADS ON THE SPINDLE NUT AND DRIVE AXLE RESULTING IN FAILURE OF THE DRIVE AXLE OR THE SPINDLE NUT. FAILURE OF EITHER OF THESE COMPONENTS CAN RESULT IN SEPARATION OF THE STEERING KNUCKLE TIRE-WHEEL ASSEMBLY FROM THE DRIVE AXLE.
THE SECOND ROW, RIGHT HAND SHOULDER BELT CAN BECOME PINCHED BETWEEN THE SEAT AND THE DOOR FRAME PILLAR TRIM. THE SHOULDER BELT MAY NOT RETRACT PROPERLY, WHICH DOES NOT COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 208, OCCUPANT CRASH PROTECTION. THE 1994 VEHICLES HAVE AN OPTIONAL INTEGRAL (BUILT IN) CHILDSEAT INSTALLED NEXT TO THE POWER SLIDING SIDE DOOR. THE 1993 INVOLVED VEHICLES HAVE STANDARD SEATS IN THAT SAME POSITION.
THE SECOND ROW, RIGHT HAND SHOULDER BELT CAN BECOME PINCHED BETWEEN THE SEAT AND THE DOOR FRAME PILLAR TRIM. THE SHOULDER BELT MAY NOT RETRACT PROPERLY, WHICH DOES NOT COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 208, OCCUPANT CRASH PROTECTION. THE 1994 VEHICLES HAVE AN OPTIONAL INTEGRAL (BUILT IN) CHILDSEAT INSTALLED NEXT TO THE POWER SLIDING SIDE DOOR. THE 1993 INVOLVED VEHICLES HAVE STANDARD SEATS IN THAT SAME POSITION.
THE FUEL FILLER NECK SOLDER JOINT CAN DEVELOP CRACKS OR PIN HOLE LEAKS, WHICH DOES NOT COMPLY WITH FMVSS NO. 301, FUEL SYSTEM INTEGRITY. THE CRACKS AND HOLES CAN ALLOW FUEL VAPOR AND FUEL LEAKAGE.
THE FUEL FILLER NECK SOLDER JOINT CAN DEVELOP CRACKS OR PIN HOLE LEAKS, WHICH DOES NOT COMPLY WITH FMVSS NO. 301, FUEL SYSTEM INTEGRITY. THE CRACKS AND HOLES CAN ALLOW FUEL VAPOR AND FUEL LEAKAGE.
THE THIRD ROW SAFETY BELT RETRACTORS MAY BE INSTALLED INCORRECTLY AND MAY LOCK-UP WHEN THE VEHICLE IS ON SLOPES OF LESS THAN 15 DEGREES, WHICH DOES NOT COMPLY WITH FMVSS NO. 209, SEAT BELT ASSEMBLIES.
VEHICLE FAILS TO CONFORM TO FMVSS NO. 209, SEAT BELT ASSEMBLIES. THE SAFETY BELT OF THE LEFT THIRD ROW SEAT ON THE SIX PASSENGER VAN AND THE CENTER SECOND ROW SEAT OF THE SEVEN PASSENGER VAN MAY LOCK UP AND CANNOT BE WITHDRAWN FROM THE RETRACTOR.
VEHICLE FAILS TO CONFORM TO FMVSS NO. 209, SEAT BELT ASSEMBLIES. THE SAFETY BELT OF THE LEFT THIRD ROW SEAT ON THE SIX PASSENGER VAN AND THE CENTER SECOND ROW SEAT OF THE SEVEN PASSENGER VAN MAY LOCK UP AND CANNOT BE WITHDRAWN FROM THE RETRACTOR.
THE SAFETY BELT RETRACTORS FOR THE REAR CENTER POSITION ARE MISSING A PAWL SPRING AND IN CASE OF AN ACCIDENT, WILL ALLOW THE SAFETY BELT WEBBING TO EXTEND BEYOND THE MINIMUM REQUIREMENTS OF FMVSS NO. 208, OCCUPANT CRASH PROTECTION.
