Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
THE FRONT AXLE ALUMINUM HUBS ON THE INVOLVED VEHICLES MAY CONTAIN A DEFICIENCY IN THE BARREL AREA BETWEEN THE INNER AND OUTER BEARINGS WHICH MAY RESULT IN CRACKS WHICH COULD EVENTUALLY LEAD TO HUB FAILURE.
THE FRONT AXLE ALUMINUM HUBS ON THE INVOLVED VEHICLES MAY CONTAIN A DEFICIENCY IN THE BARREL AREA BETWEEN THE INNER AND OUTER BEARINGS WHICH MAY RESULT IN CRACKS WHICH COULD EVENTUALLY LEAD TO HUB FAILURE.
THE FRONT AXLE ALUMINUM HUBS ON THE INVOLVED VEHICLES MAY CONTAIN A DEFICIENCY IN THE BARREL AREA BETWEEN THE INNER AND OUTER BEARINGS WHICH MAY RESULT IN CRACKS WHICH COULD EVENTUALLY LEAD TO HUB FAILURE.
THE FRONT AXLE ALUMINUM HUBS ON THE INVOLVED VEHICLES MAY CONTAIN A DEFICIENCY IN THE BARREL AREA BETWEEN THE INNER AND OUTER BEARINGS WHICH MAY RESULT IN CRACKS WHICH COULD EVENTUALLY LEAD TO HUB FAILURE.
THE FRONT AXLE ALUMINUM HUBS ON THE INVOLVED VEHICLES MAY CONTAIN A DEFICIENCY IN THE BARREL AREA BETWEEN THE INNER AND OUTER BEARINGS WHICH MAY RESULT IN CRACKS WHICH COULD EVENTUALLY LEAD TO HUB FAILURE.
THE FRONT AXLE ALUMINUM HUBS ON THE INVOLVED VEHICLES MAY CONTAIN A DEFICIENCY IN THE BARREL AREA BETWEEN THE INNER AND OUTER BEARINGS WHICH MAY RESULT IN CRACKS WHICH COULD EVENTUALLY LEAD TO HUB FAILURE.
THE FRONT AXLE ALUMINUM HUBS ON THE INVOLVED VEHICLES MAY CONTAIN A DEFICIENCY IN THE BARREL AREA BETWEEN THE INNER AND OUTER BEARINGS WHICH MAY RESULT IN CRACKS WHICH COULD EVENTUALLY LEAD TO HUB FAILURE.
THE INVOLVED VEHICLES MAY NOT COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, AIR BRAKE SYSTEMS. THE TRAILER BRAKE CONTROL AIR LINE WAS CONNECTED TO THE FRONT BRAKE DOUBLE CHECK VALVE RATHER THAN THE STOP LAMP SWITCH DOUBLE CHECK VALVE, SUCH THAT IN THE EVENT OF A FAILURE OF THE TRUCK FRONT BRAKE SYSTEM THE TRAILER BRAKES CANNOT BE APPLIED USING THE SERVICE BRAKE CONTROL (TREADLE VALVE).
THE INVOLVED VEHICLES MAY NOT COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, AIR BRAKE SYSTEMS. THE TRAILER BRAKE CONTROL AIR LINE WAS CONNECTED TO THE FRONT BRAKE DOUBLE CHECK VALVE RATHER THAN THE STOP LAMP SWITCH DOUBLE CHECK VALVE, SUCH THAT IN THE EVENT OF A FAILURE OF THE TRUCK FRONT BRAKE SYSTEM THE TRAILER BRAKES CANNOT BE APPLIED USING THE SERVICE BRAKE CONTROL (TREADLE VALVE).
THE INVOLVED VEHICLES MAY NOT COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, AIR BRAKE SYSTEMS. THE TRAILER BRAKE CONTROL AIR LINE WAS CONNECTED TO THE FRONT BRAKE DOUBLE CHECK VALVE RATHER THAN THE STOP LAMP SWITCH DOUBLE CHECK VALVE, SUCH THAT IN THE EVENT OF A FAILURE OF THE TRUCK FRONT BRAKE SYSTEM THE TRAILER BRAKES CANNOT BE APPLIED USING THE SERVICE BRAKE CONTROL (TREADLE VALVE).
ON THE INVOLVED VEHICLES, THE 110 VOLT AC CONDUIT ON THE GENERATOR MAY CONTACT THE POSITIVE BATTERY TERMINAL, OR THE STARTER SOLENOID POST, CAUSING A SHORT TO GROUND OF BATTERY POWER. ALSO, THE 110 VOLT AC CONDUIT AND CABLE INSULATION MAY CHAFE AGAINST THE NEGATIVE TERMINAL, CAUSING A SHORT TO GROUND OF 110 VOLT AC POWER.
ON THE INVOLVED VEHICLES, THE 110 VOLT AC CONDUIT ON THE GENERATOR MAY CONTACT THE POSITIVE BATTERY TERMINAL, OR THE STARTER SOLENOID POST, CAUSING A SHORT TO GROUND OF BATTERY POWER. ALSO, THE 110 VOLT AC CONDUIT AND CABLE INSULATION MAY CHAFE AGAINST THE NEGATIVE TERMINAL, CAUSING A SHORT TO GROUND OF 110 VOLT AC POWER.
ON THE INVOLVED VEHICLES, THE NUTS WHICH ATTACH THE BRAKE MASTER CYLINDER TO THE HYDRO-BOOST UNIT MAY HAVE BEEN OVER-TIGHTENED. THIS COULD HAVE CAUSED STRIPPED THREADS AND CRACKED ATTACHING FLANGES. SHOULD THESE NUTS FAIL, THE PARTS MAY SEPARATE AND LOSS OF SERVICE BRAKES WOULD RESULT.
ON THE INVOLVED VEHICLES, THE BRAKE MASTER CYLINDER MAY HAVE BEEN ASSEMBLED WITH RESERVOIR MOUNTING BOLTS THAT WERE IMPROPERLY PROCESSED. THIS COULD MAKE THESE BOLTS BRITTLE AND SUBJECT TO BREAKING. IF BREAKAGE OCCURS, A BRAKE FLUID LEAK MAY DEVELOP BETWEEN THE RESERVOIR AND MASTER CYLINDER. LOSS OF BRAKE FLUID WOULD ADVERSELY AFFECT VEHICLE BRAKING CAPABILITY.
ON THE INVOLVED VEHICLES, THE BRAKE MASTER CYLINDER MAY HAVE BEEN ASSEMBLED WITH RESERVOIR MOUNTING BOLTS THAT WERE IMPROPERLY PROCESSED. THIS COULD MAKE THESE BOLTS BRITTLE AND SUBJECT TO BREAKING. IF BREAKAGE OCCURS, A BRAKE FLUID LEAK MAY DEVELOP BETWEEN THE RESERVOIR AND MASTER CYLINDER. LOSS OF BRAKE FLUID WOULD ADVERSELY AFFECT VEHICLE BRAKING CAPABILITY.
THE FRONT SUSPENSION CONTROL ARMS WERE ASSEMBLED WITH BALL JOINTS WHICH MAY CONTAIN SOCKETS THAT WERE NOT PROPERLY HEAT-TREATED. THIS MAY CAUSE THE SOCKET TO WEAR RAPIDLY AND ALLOW THE BALL JOINT STUD TO SEPARATE FROM THE SOCKET, CAUSING EITHER THE LEFT OR RIGHT WHEEL SUSPENSION TO COLLAPSE.
THE FRONT SUSPENSION CONTROL ARMS WERE ASSEMBLED WITH BALL JOINTS WHICH MAY CONTAIN SOCKETS THAT WERE NOT PROPERLY HEAT-TREATED. THIS MAY CAUSE THE SOCKET TO WEAR RAPIDLY AND ALLOW THE BALL JOINT STUD TO SEPARATE FROM THE SOCKET, CAUSING EITHER THE LEFT OR RIGHT WHEEL SUSPENSION TO COLLAPSE.
THE FRONT SUSPENSION CONTROL ARMS WERE ASSEMBLED WITH BALL JOINTS WHICH MAY CONTAIN SOCKETS THAT WERE NOT PROPERLY HEAT-TREATED. THIS MAY CAUSE THE SOCKET TO WEAR RAPIDLY AND ALLOW THE BALL JOINT STUD TO SEPARATE FROM THE SOCKET, CAUSING EITHER THE LEFT OR RIGHT WHEEL SUSPENSION TO COLLAPSE.
THE FRONT SUSPENSION CONTROL ARMS WERE ASSEMBLED WITH BALL JOINTS WHICH MAY CONTAIN SOCKETS THAT WERE NOT PROPERLY HEAT-TREATED. THIS MAY CAUSE THE SOCKET TO WEAR RAPIDLY AND ALLOW THE BALL JOINT STUD TO SEPARATE FROM THE SOCKET, CAUSING EITHER THE LEFT OR RIGHT WHEEL SUSPENSION TO COLLAPSE.
THE FRONT SUSPENSION CONTROL ARMS WERE ASSEMBLED WITH BALL JOINTS WHICH MAY CONTAIN SOCKETS THAT WERE NOT PROPERLY HEAT-TREATED. THIS MAY CAUSE THE SOCKET TO WEAR RAPIDLY AND ALLOW THE BALL JOINT STUD TO SEPARATE FROM THE SOCKET, CAUSING EITHER THE LEFT OR RIGHT WHEEL SUSPENSION TO COLLAPSE.
THE FRONT SUSPENSION CONTROL ARMS WERE ASSEMBLED WITH BALL JOINTS WHICH MAY CONTAIN SOCKETS THAT WERE NOT PROPERLY HEAT-TREATED. THIS MAY CAUSE THE SOCKET TO WEAR RAPIDLY AND ALLOW THE BALL JOINT STUD TO SEPARATE FROM THE SOCKET, CAUSING EITHER THE LEFT OR RIGHT WHEEL SUSPENSION TO COLLAPSE.
THE FRONT SUSPENSION CONTROL ARMS WERE ASSEMBLED WITH BALL JOINTS WHICH MAY CONTAIN SOCKETS THAT WERE NOT PROPERLY HEAT-TREATED. THIS MAY CAUSE THE SOCKET TO WEAR RAPIDLY AND ALLOW THE BALL JOINT STUD TO SEPARATE FROM THE SOCKET, CAUSING EITHER THE LEFT OR RIGHT WHEEL SUSPENSION TO COLLAPSE.
THE WHEELS ON THE INVOLVED VEHICLES MAY BE EQUIPPED WITH AN IMPROPERLY FORMED SPIDER IN THE AREA WHERE THE SPIDER ATTACHES TO THE RIM. CONSEQUENTLY, THE CENTER SECTION OF THE WHEEL MAY DEVELOP CRACKS AND SEPARATE FROM THE WHEEL RIM.
