Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
SOME ANTI-LOCK CONTROLLERS CONTAIN ELECTRONIC COMPONENTS WHICH WERE NOT MADE TO SPECIFICATIONS. IN THE EVENT THESE CONTROLLERS DEVELOP A FAILURE OF ANOTHER INTERNAL ELECTRIC COMPONENT, THE COMBINATION OF DEFECTS MAY CAUSE THE ANTI-LOCK VALVE SOLENOID (A COILED CURRENT CONDUCTING WIRE) TO BE CONTINUOUSLY ENERGIZED, PREVENTING APPLICATION OF THE BRAKES ON THE AXLE INVOLVED. HOWEVER, THE ANTI-LOCK BRAKING SYSTEM PERFORMANCE ON THE REMAINDER OF THE VEHICLE IS NOT AFFECTED AND THE DRIVER WARNING LIGHT IS NOT ACTUATED.
SOME ANTI-LOCK CONTROLLERS CONTAIN ELECTRONIC COMPONENTS WHICH WERE NOT MADE TO SPECIFICATIONS. IN THE EVENT THESE CONTROLLERS DEVELOP A FAILURE OF ANOTHER INTERNAL ELECTRIC COMPONENT, THE COMBINATION OF DEFECTS MAY CAUSE THE ANTI-LOCK VALVE SOLENOID (A COILED CURRENT CONDUCTING WIRE) TO BE CONTINUOUSLY ENERGIZED, PREVENTING APPLICATION OF THE BRAKES ON THE AXLE INVOLVED. HOWEVER, THE ANTI-LOCK BRAKING SYSTEM PERFORMANCE ON THE REMAINDER OF THE VEHICLE IS NOT AFFECTED AND THE DRIVER WARNING LIGHT IS NOT ACTUATED.
SOME ANTI-LOCK CONTROLLERS CONTAIN ELECTRONIC COMPONENTS WHICH WERE NOT MADE TO SPECIFICATIONS. IN THE EVENT THESE CONTROLLERS DEVELOP A FAILURE OF ANOTHER INTERNAL ELECTRIC COMPONENT, THE COMBINATION OF DEFECTS MAY CAUSE THE ANTI-LOCK VALVE SOLENOID (A COILED CURRENT CONDUCTING WIRE) TO BE CONTINUOUSLY ENERGIZED, PREVENTING APPLICATION OF THE BRAKES ON THE AXLE INVOLVED. HOWEVER, THE ANTI-LOCK BRAKING SYSTEM PERFORMANCE ON THE REMAINDER OF THE VEHICLE IS NOT AFFECTED AND THE DRIVER WARNING LIGHT IS NOT ACTUATED.
SOME ANTI-LOCK CONTROLLERS CONTAIN ELECTRONIC COMPONENTS WHICH WERE NOT MADE TO SPECIFICATIONS. IN THE EVENT THESE CONTROLLERS DEVELOP A FAILURE OF ANOTHER INTERNAL ELECTRIC COMPONENT, THE COMBINATION OF DEFECTS MAY CAUSE THE ANTI-LOCK VALVE SOLENOID (A COILED CURRENT CONDUCTING WIRE) TO BE CONTINUOUSLY ENERGIZED, PREVENTING APPLICATION OF THE BRAKES ON THE AXLE INVOLVED. HOWEVER, THE ANTI-LOCK BRAKING SYSTEM PERFORMANCE ON THE REMAINDER OF THE VEHICLE IS NOT AFFECTED AND THE DRIVER WARNING LIGHT IS NOT ACTUATED.
THE LEFT AND RIGHT FRONT SUSPENSION CROSSMEMBER STRUT RODS, WHICH GIVE ADDED STRENGTH, MAY HAVE BEEN OMITTED DURING ASSEMBLY. CONSEQUENTLY, A FRAME CROSSMEMBER CRACK COULD EVENTUALLY DEVELOP AT THE FORWARD VERTICAL FRONT SUSPENSION BOLT.
ON THE INVOLVED VEHICLES, AN INTERFERENCE CONDITION MAY EXIST BETWEEN THE CARBURETOR FUEL PIPE ASSEMBLY AND THE AIR CONDITIONING BRACKET. THIS COULD EVENTUALLY CAUSE THE PIPE TO WEAR THROUGH DUE TO VIBRATION AND FUEL PRESSURE PULSATION.
ON THE INVOLVED VEHICLES, AN INTERFERENCE CONDITION MAY EXIST BETWEEN THE CARBURETOR FUEL PIPE ASSEMBLY AND THE AIR CONDITIONING BRACKET. THIS COULD EVENTUALLY CAUSE THE PIPE TO WEAR THROUGH DUE TO VIBRATION AND FUEL PRESSURE PULSATION.
THESE VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, AIR BRAKE SYSTEMS. THESE VEHICLES WERE BUILT WITH AN INCORRECT RESISTOR BOARD IN THE EATON CONTROLLER ON THE WHEEL LOCK CONTROL VALVE.
THESE VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, AIR BRAKE SYSTEMS. THESE VEHICLES WERE BUILT WITH AN INCORRECT RESISTOR BOARD IN THE EATON CONTROLLER ON THE WHEEL LOCK CONTROL VALVE.
THE EXISTING CERTIFICATION LABELS CONTAIN INCORRECT RIM SIZE INFORMATION. THIS IS A NON-COMPLIANCE TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 120, TIRE SELECTION AND RIMS FOR VEHICLES OTHER THAN PASSENGER CARS. THE EXISTING LABELS SPECIFY THE USE OF 16.5X6.00 REAR WHEELS INSTEAD OF THE CORRECT 16.5X6.75 WHEELS.
THE INVOLVED VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, SEAT BELT ASSEMBLIES IN THAT THE RIGHT HAND SEAT BELT RETRACTORS USED AT BOTH THE DRIVER AND FRONT PASSENGER SEAT POSITIONS MAY HAVE BEEN MISASSEMBLED. AS A RESULT, THEY MAY NOT LOCK.
THE INVOLVED VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, SEAT BELT ASSEMBLIES IN THAT THE RIGHT HAND SEAT BELT RETRACTORS USED AT BOTH THE DRIVER AND FRONT PASSENGER SEAT POSITIONS MAY HAVE BEEN MISASSEMBLED. AS A RESULT, THEY MAY NOT LOCK.
THE INVOLVED VEHICLES DO NOT CONTAIN AN EMERGENCY STOP CONTROL FOR EMERGENCY STOPPING OF THE VEHICLE. THIS EMERGENCY STOP CONTROL IS NECESSARY TO PREVENT ENGINE OVERSPEED AND TO STOP THE ENGINE IN CASE OF A FUEL MALFUNCTION.
THE INVOLVED VEHICLES DO NOT CONTAIN AN EMERGENCY STOP CONTROL FOR EMERGENCY STOPPING OF THE VEHICLE. THIS EMERGENCY STOP CONTROL IS NECESSARY TO PREVENT ENGINE OVERSPEED AND TO STOP THE ENGINE IN CASE OF A FUEL MALFUNCTION.
THE INTERMEDIATE SHAFT COUPLING ON THE INVOLVED VEHICLES MAY HAVE BEEN MACHINED OVERSIZED IN THE SERRATION AREA WHERE IT ATTACHES TO THE STEERING COLUMN. THIS WOULD PREVENT THE COUPLING FROM PROPERLY TIGHTENING ON THE SHAFT WHEN THE CLAMP AND PINCH BOLT WERE INSTALLED.
THE INVOLVED VEHICLES FAIL TO COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 207, ANCHORAGE OF SEATS, DUE TO POSSIBLE FAILURE OF THE SEAT POST ATTACHMENT AT THE FLOOR IN THE EVENT OF AN ACCIDENT. THESE VEHICLES HAVE OVERSIZED BOLT HOLES IN THE FLOOR PAN WHICH MAY ALLOW THE SEAT ATTACHING NUTS TO PASS THROUGH THEM AND THUS TIGHTEN AGAINST THE BOTTOM OF THE SEAT BASE INSTEAD OF THE LONGITUDINAL SILL.
THE INVOLVED VEHICLES ARE IN NON-COMPLIANCE WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 207, ANCHORAGE OF SEATS, DUE TO THE POSSIBILITY FOR THE FRONT SEATS TO SEPARATE FROM THE SEAT ADJUSTER TRACKS. THE SEPARATION MAY OCCUR BECAUSE THE NUTS ON THE SEAT FRAME CAN BE PULLED TOTALLY OR PARTIALLY THROUGH THE SEAT FRAME SINCE THE SPACERS USED BETWEEN THE ADJUSTER AND THE SEAT FRAMES DO NOT PROVIDE ADEQUATE SUPPORT OF THE NUT MOUNTING SURFACES.
THE ACCELERATOR PEDAL ROD IN COMBINATION WITH THE PEDAL INSTALLED ON THE INVOLVED VEHICLES MAY CUT THROUGH THE FLOOR PAN RUBBER MAT OR CARPET INTO THE THICK RESILIENT INSULATION PAD UNDERNEATH DURING HEAVY OR REPEATED FULL THROTTLE APPLICATIONS. AS A RESULT, THE ACCELERATOR PEDAL ROD MAY CATCH IN THE MAT OR CARPET, PREVENTING THE THROTTLE FROM RETURNING TO IDLE WHEN THE DRIVERS FOOT IS REMOVED FROM THE PEDAL.
THE ACCELERATOR PEDAL ROD IN COMBINATION WITH THE PEDAL INSTALLED ON THE INVOLVED VEHICLES MAY CUT THROUGH THE FLOOR PAN RUBBER MAT OR CARPET INTO THE THICK RESILIENT INSULATION PAD UNDERNEATH DURING HEAVY OR REPEATED FULL THROTTLE APPLICATIONS. AS A RESULT, THE ACCELERATOR PEDAL ROD MAY CATCH IN THE MAT OR CARPET, PREVENTING THE THROTTLE FROM RETURNING TO IDLE WHEN THE DRIVERS FOOT IS REMOVED FROM THE PEDAL.
THE ACCELERATOR PEDAL ROD IN COMBINATION WITH THE PEDAL INSTALLED ON THE INVOLVED VEHICLES MAY CUT THROUGH THE FLOOR PAN RUBBER MAT OR CARPET INTO THE THICK RESILIENT INSULATION PAD UNDERNEATH DURING HEAVY OR REPEATED FULL THROTTLE APPLICATIONS. AS A RESULT, THE ACCELERATOR PEDAL ROD MAY CATCH IN THE MAT OR CARPET, PREVENTING THE THROTTLE FROM RETURNING TO IDLE WHEN THE DRIVERS FOOT IS REMOVED FROM THE PEDAL.
THE ACCELERATOR PEDAL ROD IN COMBINATION WITH THE PEDAL INSTALLED ON THE INVOLVED VEHICLES MAY CUT THROUGH THE FLOOR PAN RUBBER MAT OR CARPET INTO THE THICK RESILIENT INSULATION PAD UNDERNEATH DURING HEAVY OR REPEATED FULL THROTTLE APPLICATIONS. AS A RESULT, THE ACCELERATOR PEDAL ROD MAY CATCH IN THE MAT OR CARPET, PREVENTING THE THROTTLE FROM RETURNING TO IDLE WHEN THE DRIVERS FOOT IS REMOVED FROM THE PEDAL.
THE ACCELERATOR PEDAL ROD IN COMBINATION WITH THE PEDAL INSTALLED ON THE INVOLVED VEHICLES MAY CUT THROUGH THE FLOOR PAN RUBBER MAT OR CARPET INTO THE THICK RESILIENT INSULATION PAD UNDERNEATH DURING HEAVY OR REPEATED FULL THROTTLE APPLICATIONS. AS A RESULT, THE ACCELERATOR PEDAL ROD MAY CATCH IN THE MAT OR CARPET, PREVENTING THE THROTTLE FROM RETURNING TO IDLE WHEN THE DRIVERS FOOT IS REMOVED FROM THE PEDAL.
THE ACCELERATOR PEDAL ROD IN COMBINATION WITH THE PEDAL INSTALLED ON THE INVOLVED VEHICLES MAY CUT THROUGH THE FLOOR PAN RUBBER MAT OR CARPET INTO THE THICK RESILIENT INSULATION PAD UNDERNEATH DURING HEAVY OR REPEATED FULL THROTTLE APPLICATIONS. AS A RESULT, THE ACCELERATOR PEDAL ROD MAY CATCH IN THE MAT OR CARPET, PREVENTING THE THROTTLE FROM RETURNING TO IDLE WHEN THE DRIVERS FOOT IS REMOVED FROM THE PEDAL.
THE ACCELERATOR PEDAL ROD IN COMBINATION WITH THE PEDAL INSTALLED ON THE INVOLVED VEHICLES MAY CUT THROUGH THE FLOOR PAN RUBBER MAT OR CARPET INTO THE THICK RESILIENT INSULATION PAD UNDERNEATH DURING HEAVY OR REPEATED FULL THROTTLE APPLICATIONS. AS A RESULT, THE ACCELERATOR PEDAL ROD MAY CATCH IN THE MAT OR CARPET, PREVENTING THE THROTTLE FROM RETURNING TO IDLE WHEN THE DRIVERS FOOT IS REMOVED FROM THE PEDAL.
THE ACCELERATOR PEDAL ROD IN COMBINATION WITH THE PEDAL INSTALLED ON THE INVOLVED VEHICLES MAY CUT THROUGH THE FLOOR PAN RUBBER MAT OR CARPET INTO THE THICK RESILIENT INSULATION PAD UNDERNEATH DURING HEAVY OR REPEATED FULL THROTTLE APPLICATIONS. AS A RESULT, THE ACCELERATOR PEDAL ROD MAY CATCH IN THE MAT OR CARPET, PREVENTING THE THROTTLE FROM RETURNING TO IDLE WHEN THE DRIVERS FOOT IS REMOVED FROM THE PEDAL.
THE ACCELERATOR PEDAL ROD IN COMBINATION WITH THE PEDAL INSTALLED ON THE INVOLVED VEHICLES MAY CUT THROUGH THE FLOOR PAN RUBBER MAT OR CARPET INTO THE THICK RESILIENT INSULATION PAD UNDERNEATH DURING HEAVY OR REPEATED FULL THROTTLE APPLICATIONS. AS A RESULT, THE ACCELERATOR PEDAL ROD MAY CATCH IN THE MAT OR CARPET, PREVENTING THE THROTTLE FROM RETURNING TO IDLE WHEN THE DRIVERS FOOT IS REMOVED FROM THE PEDAL.
THE ACCELERATOR PEDAL ROD IN COMBINATION WITH THE PEDAL INSTALLED ON THE INVOLVED VEHICLES MAY CUT THROUGH THE FLOOR PAN RUBBER MAT OR CARPET INTO THE THICK RESILIENT INSULATION PAD UNDERNEATH DURING HEAVY OR REPEATED FULL THROTTLE APPLICATIONS. AS A RESULT, THE ACCELERATOR PEDAL ROD MAY CATCH IN THE MAT OR CARPET, PREVENTING THE THROTTLE FROM RETURNING TO IDLE WHEN THE DRIVERS FOOT IS REMOVED FROM THE PEDAL.
THE INVOLVED VEHICLES WERE ASSEMBLED WITH A STANDARD FRONT SUSPENSION ASSEMBLY, INSTEAD OF THE SPECIFIED HEAVY-DUTY FRONT SUSPENSION. OPERATION OF VEHICLE WHILE CARRYING THE MAXIMUM RATED LOAD MAY LEAD TO DETERIORATION AND EVENTUAL FAILURE OF FRONT SUSPENSION COMPONENTS.
THE FRONT AXLE ALUMINUM HUBS ON THE INVOLVED VEHICLES MAY CONTAIN A DEFICIENCY IN THE BARREL AREA BETWEEN THE INNER AND OUTER BEARINGS WHICH MAY RESULT IN CRACKS WHICH COULD EVENTUALLY LEAD TO HUB FAILURE.
THE FRONT AXLE ALUMINUM HUBS ON THE INVOLVED VEHICLES MAY CONTAIN A DEFICIENCY IN THE BARREL AREA BETWEEN THE INNER AND OUTER BEARINGS WHICH MAY RESULT IN CRACKS WHICH COULD EVENTUALLY LEAD TO HUB FAILURE.
