Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
BRAKES MAY FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, AIR BRAKE SYSTEMS. THE AIR BRAKES ON THE FRONT AXLE MAY NOT ACTUATE AND RELEASE WITHIN THE TIME REQUIRED FOR SAFE BRAKING. THE BRAKES MAY EXCEED THE .55 SECOND LIMITS.
BRAKES MAY FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, AIR BRAKE SYSTEMS. THE AIR BRAKES ON THE FRONT AXLE MAY NOT ACTUATE AND RELEASE WITHIN THE TIME REQUIRED FOR SAFE BRAKING. THE BRAKES MAY EXCEED THE .55 SECOND LIMITS.
BRAKES MAY FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, AIR BRAKE SYSTEMS. THE AIR BRAKES ON THE FRONT AXLE MAY NOT ACTUATE AND RELEASE WITHIN THE TIME REQUIRED FOR SAFE BRAKING. THE BRAKES MAY EXCEED THE .55 SECOND LIMITS.
SOME OF THE INVOLVED VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, AIR BRAKE SYSTEMS. THE RELEASE TIME FOR THE REAR BRAKES MAY EXCEED THE .55 SECOND LIMIT REQUIREMENT FOR SAFE BRAKING.
AN AIR BRAKE HOSE FITTING BENEATH THE FLOOR OF THE SUBJECT VEHICLES MAY RUB AGAINST THE ROTATING STEERING DRIVE SHAFT, EVENTUALLY CAUSING THE SHAFT TO FRACTURE. THIS CONDITION COULD EXIST IF A MECHANIC FAILED TO ORIENT THE THREADED 90 DEGREE ELBOW FITTING IN THE PROPER DIRECTION, OR IF THE STEERING COLUMN WAS POSITIONED INCORRECTLY. ALSO, AN IMPROPERLY ASSEMBLED BEARING PLATE WAS INSTALLED ON THE STEERING DRIVE SHAFT. THIS COULD CAUSE THE SLIP SHAFT TO BOTTOM OUT, RESULTING IN DAMAGE TO THE STEERING YOKE CONNECTION OR TO THE INTERNAL PARTS OF THE GEAR BOX.
THE KNUCKLE STOP NUTS ARE TOO SHORT, POSSIBLY RESULTING IN FAILURE OF THE NUT UNDER HEAVY STEERING FORCE. THIS MAY ALLOW THE WHEEL TO ROTATE TOO FAR TO THE RIGHT OR LEFT, PERMITTING THE TIRE TO CONTACT OTHER VEHICLE PARTS.
THE FOUR BOLTS USED TO ATTACH EACH FUEL TANK SUPPORT BRACKET TO THE FRAME CONTAIN QUENCH CRACKS DUE TO IMPROPER HEAT TREATMENT IN THE MANUFACTURING PROCESS. THESE DEFECTIVE BOLTS COULD GIVE WAY, ALLOWING THE FUEL TANK TO BECOME DISLODGED FROM THE BRACKET OR THE BRACKET FROM THE FRAME.
THE SAFETY CHAIN BALE PORTION OF THE TOWING ATTACHMENT MAY HAVE A DEFECTIVE WELD IN A CRITICAL AREA. IF THE TRAILER HITCH SHOULD BECOME UNLATCHED OR IN THE EVENT OF AN ACCIDENT CAUSING THE TRUCK AND TRAILER TO BECOME SEPARATED, THE RESULTING FORCES COULD CAUSE A FAILURE OF THE SAFETY CHAIN BALE. A FAILURE OF THIS PART WOULD ALLOW COMPLETE SEPARATION OF THE TRUCK AND TRAILER WITHOUT PRIOR WARNING.
THE SAFETY CHAIN BALE PORTION OF THE TOWING ATTACHMENT MAY HAVE A DEFECTIVE WELD IN A CRITICAL AREA. IF THE TRAILER HITCH SHOULD BECOME UNLATCHED OR IN THE EVENT OF AN ACCIDENT CAUSING THE TRUCK AND TRAILER TO BECOME SEPARATED, THE RESULTING FORCES COULD CAUSE A FAILURE OF THE SAFETY CHAIN BALE. A FAILURE OF THIS PART WOULD ALLOW COMPLETE SEPARATION OF THE TRUCK AND TRAILER WITHOUT PRIOR WARNING.
THE SAFETY CHAIN BALE PORTION OF THE TOWING ATTACHMENT MAY HAVE A DEFECTIVE WELD IN A CRITICAL AREA. IF THE TRAILER HITCH SHOULD BECOME UNLATCHED OR IN THE EVENT OF AN ACCIDENT CAUSING THE TRUCK AND TRAILER TO BECOME SEPARATED, THE RESULTING FORCES COULD CAUSE A FAILURE OF THE SAFETY CHAIN BALE. A FAILURE OF THIS PART WOULD ALLOW COMPLETE SEPARATION OF THE TRUCK AND TRAILER WITHOUT PRIOR WARNING.
ON THE INVOLVED VEHICLES, BOTH THE AIR BRAKE HOSE CONNECTIONS AND THE AIR PRESSURE GAUGES FOR THE DUEL BRAKE FEATURE MAY HAVE BEEN CONNECTED IN REVERSE ORDER. INCORRECTLY CONNECTED BRAKE HOSES IN COMBINATION WITH AN AIR LEAK IN EITHER THE PRIMARY OR SECONDARY BRAKE SYSTEMS COULD CAUSE BRAKE FAILURE ON ONE OR MORE AXLES.
ON CERTAIN VEHICLES, SOME COTTER PINS MAY BE MISSING AT THE BALL JOINT CONNECTIONS OF THE DRAG LINK ENDS AND TIE ROD ENDS IN THE LOWER FRONT AXLE STEERING SYSTEM. STEERING JOINT COULD SEPARATE IF THE BALL STUD RETAINING NUT LOOSENS AND FALLS OFF DUE TO ABSENCE OF COTTER PIN.
ON INVOLVED VEHICLES, THE CONNECTION BETWEEN THE STEERING CONTROL SHAFT AND THE INPUT SHAFT ON THE STEERING GEAR BOX MAY BE DEFECTIVE. THE YOKE ON THE SHAFT MAY LOOSEN, ALLOWING THE SPLINED SURFACES ON THE YOKE AND SHAFT TO WEAR. CONTINUED OPERATION MAY RESULT IN WEAR AND EVENTUAL ROTATIONAL SLIPPAGE OF THE JOINT.
ON INVOLVED VEHICLES, THE CONNECTION BETWEEN THE STEERING CONTROL SHAFT AND THE INPUT SHAFT ON THE STEERING GEAR BOX MAY BE DEFECTIVE. THE YOKE ON THE SHAFT MAY LOOSEN, ALLOWING THE SPLINED SURFACES ON THE YOKE AND SHAFT TO WEAR. CONTINUED OPERATION MAY RESULT IN WEAR AND EVENTUAL ROTATIONAL SLIPPAGE OF THE JOINT.
ON INVOLVED VEHICLES, THE CONNECTION BETWEEN THE STEERING CONTROL SHAFT AND THE INPUT SHAFT ON THE STEERING GEAR BOX MAY BE DEFECTIVE. THE YOKE ON THE SHAFT MAY LOOSEN, ALLOWING THE SPLINED SURFACES ON THE YOKE AND SHAFT TO WEAR. CONTINUED OPERATION MAY RESULT IN WEAR AND EVENTUAL ROTATIONAL SLIPPAGE OF THE JOINT.
ON INVOLVED VEHICLES, THE CONNECTION BETWEEN THE STEERING CONTROL SHAFT AND THE INPUT SHAFT ON THE STEERING GEAR BOX MAY BE DEFECTIVE. THE YOKE ON THE SHAFT MAY LOOSEN, ALLOWING THE SPLINED SURFACES ON THE YOKE AND SHAFT TO WEAR. CONTINUED OPERATION MAY RESULT IN WEAR AND EVENTUAL ROTATIONAL SLIPPAGE OF THE JOINT.
ON INVOLVED VEHICLES, THE CONNECTION BETWEEN THE STEERING CONTROL SHAFT AND THE INPUT SHAFT ON THE STEERING GEAR BOX MAY BE DEFECTIVE. THE YOKE ON THE SHAFT MAY LOOSEN, ALLOWING THE SPLINED SURFACES ON THE YOKE AND SHAFT TO WEAR. CONTINUED OPERATION MAY RESULT IN WEAR AND EVENTUAL ROTATIONAL SLIPPAGE OF THE JOINT.
ON INVOLVED VEHICLES, THE CONNECTION BETWEEN THE STEERING CONTROL SHAFT AND THE INPUT SHAFT ON THE STEERING GEAR BOX MAY BE DEFECTIVE. THE YOKE ON THE SHAFT MAY LOOSEN, ALLOWING THE SPLINED SURFACES ON THE YOKE AND SHAFT TO WEAR. CONTINUED OPERATION MAY RESULT IN WEAR AND EVENTUAL ROTATIONAL SLIPPAGE OF THE JOINT.
ON INVOLVED VEHICLES, THE CONNECTION BETWEEN THE STEERING CONTROL SHAFT AND THE INPUT SHAFT ON THE STEERING GEAR BOX MAY BE DEFECTIVE. THE YOKE ON THE SHAFT MAY LOOSEN, ALLOWING THE SPLINED SURFACES ON THE YOKE AND SHAFT TO WEAR. CONTINUED OPERATION MAY RESULT IN WEAR AND EVENTUAL ROTATIONAL SLIPPAGE OF THE JOINT.
ON INVOLVED VEHICLES, THE CONNECTION BETWEEN THE STEERING CONTROL SHAFT AND THE INPUT SHAFT ON THE STEERING GEAR BOX MAY BE DEFECTIVE. THE YOKE ON THE SHAFT MAY LOOSEN, ALLOWING THE SPLINED SURFACES ON THE YOKE AND SHAFT TO WEAR. CONTINUED OPERATION MAY RESULT IN WEAR AND EVENTUAL ROTATIONAL SLIPPAGE OF THE JOINT.
CRACKS MAY DEVELOP IN THE TRUCKS REAR TOWING CROSSMEMBER WHICH SUPPORTS THE TRAILER HITCH AND TO WHICH THE SAFETY CABLES ARE ATTACHED. SHOULD THESE CRACKS PROGRESS TO THE POINT OF COMPLETE SEPARATION, THE CROSSMEMBER AND THE TRAILER COULD BECOME DETACHED FROM THE TRUCK.
CRACKS MAY DEVELOP IN THE TRUCKS REAR TOWING CROSSMEMBER WHICH SUPPORTS THE TRAILER HITCH AND TO WHICH THE SAFETY CABLES ARE ATTACHED. SHOULD THESE CRACKS PROGRESS TO THE POINT OF COMPLETE SEPARATION, THE CROSSMEMBER AND THE TRAILER COULD BECOME DETACHED FROM THE TRUCK.
CRACKS MAY DEVELOP IN THE TRUCKS REAR TOWING CROSSMEMBER WHICH SUPPORTS THE TRAILER HITCH AND TO WHICH THE SAFETY CABLES ARE ATTACHED. SHOULD THESE CRACKS PROGRESS TO THE POINT OF COMPLETE SEPARATION, THE CROSSMEMBER AND THE TRAILER COULD BECOME DETACHED FROM THE TRUCK.
CRACKS MAY DEVELOP IN THE TRUCKS REAR TOWING CROSSMEMBER WHICH SUPPORTS THE TRAILER HITCH AND TO WHICH THE SAFETY CABLES ARE ATTACHED. SHOULD THESE CRACKS PROGRESS TO THE POINT OF COMPLETE SEPARATION, THE CROSSMEMBER AND THE TRAILER COULD BECOME DETACHED FROM THE TRUCK.
CRACKS MAY DEVELOP IN THE TRUCKS REAR TOWING CROSSMEMBER WHICH SUPPORTS THE TRAILER HITCH AND TO WHICH THE SAFETY CABLES ARE ATTACHED. SHOULD THESE CRACKS PROGRESS TO THE POINT OF COMPLETE SEPARATION, THE CROSSMEMBER AND THE TRAILER COULD BECOME DETACHED FROM THE TRUCK.
CRACKS MAY DEVELOP IN THE TRUCKS REAR TOWING CROSSMEMBER WHICH SUPPORTS THE TRAILER HITCH AND TO WHICH THE SAFETY CABLES ARE ATTACHED. SHOULD THESE CRACKS PROGRESS TO THE POINT OF COMPLETE SEPARATION, THE CROSSMEMBER AND THE TRAILER COULD BECOME DETACHED FROM THE TRUCK.
CRACKS MAY DEVELOP IN THE TRUCKS REAR TOWING CROSSMEMBER WHICH SUPPORTS THE TRAILER HITCH AND TO WHICH THE SAFETY CABLES ARE ATTACHED. SHOULD THESE CRACKS PROGRESS TO THE POINT OF COMPLETE SEPARATION, THE CROSSMEMBER AND THE TRAILER COULD BECOME DETACHED FROM THE TRUCK.
CRACKS MAY DEVELOP IN THE TRUCKS REAR TOWING CROSSMEMBER WHICH SUPPORTS THE TRAILER HITCH AND TO WHICH THE SAFETY CABLES ARE ATTACHED. SHOULD THESE CRACKS PROGRESS TO THE POINT OF COMPLETE SEPARATION, THE CROSSMEMBER AND THE TRAILER COULD BECOME DETACHED FROM THE TRUCK.
THE INVOLVED VEHICLES FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, AIR BRAKE SYSTEMS. THE BRAKE DRUMS DO NOT MEET WITH BRAKE RECOVERY REQUIREMENTS. BRAKES MAY BE NOT PERFORM ADEQUATELY ON LONG DOWNGRADES OR DUE TO HEAVY APPLICATIONS OF AIR WHEN THE VEHICLE IS BROUGHT TO A STOP FROM HIGH SPEEDS.
THE PARK/RUN VALVE IN THE WINDSHIELD WIPER MOTOR MAY STICK IN THE PARK POSITION. AN OUT OF BALANCE DIMENSION IN THE CYLINDER RESULTED IN AN UNDERSIZED BORE WHICH MAY CAUSE THE PLUNGER TO STICK. THEREFORE, THE WIPER MOTOR MAY FAIL TO START.
