Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
BATTERY CAP VENTS MAY BE PARTIALLY OR COMPLETELY BLOCKED WITH PLASTIC FLASHING. CONSEQUENCE OF DEFECT: A BUILD UP OF INTERNAL GAS PRESSURE COULD OCCUR WHICH COULD RESULT IN CASE RUPTURE, PARTICULARLY DURING POST CHARGING. SHOULD A PERSON BE IN THE VICINITY OF THE BATTERY WHEN THE CASE RUPTURES, THEY MAY BE INJURED BY THE RELEASED GASES AND/OR ACID.
BATTERY CAP VENTS MAY BE PARTIALLY OR COMPLETELY BLOCKED WITH PLASTIC FLASHING. CONSEQUENCE OF DEFECT: A BUILD UP OF INTERNAL GAS PRESSURE COULD OCCUR WHICH COULD RESULT IN CASE RUPTURE, PARTICULARLY DURING POST CHARGING. SHOULD A PERSON BE IN THE VICINITY OF THE BATTERY WHEN THE CASE RUPTURES, THEY MAY BE INJURED BY THE RELEASED GASES AND/OR ACID.
BATTERY CAP VENTS MAY BE PARTIALLY OR COMPLETELY BLOCKED WITH PLASTIC FLASHING. CONSEQUENCE OF DEFECT: A BUILD UP OF INTERNAL GAS PRESSURE COULD OCCUR WHICH COULD RESULT IN CASE RUPTURE, PARTICULARLY DURING POST CHARGING. SHOULD A PERSON BE IN THE VICINITY OF THE BATTERY WHEN THE CASE RUPTURES, THEY MAY BE INJURED BY THE RELEASED GASES AND/OR ACID.
BATTERY CAP VENTS MAY BE PARTIALLY OR COMPLETELY BLOCKED WITH PLASTIC FLASHING. CONSEQUENCE OF DEFECT: A BUILD UP OF INTERNAL GAS PRESSURE COULD OCCUR WHICH COULD RESULT IN CASE RUPTURE, PARTICULARLY DURING POST CHARGING. SHOULD A PERSON BE IN THE VICINITY OF THE BATTERY WHEN THE CASE RUPTURES, THEY MAY BE INJURED BY THE RELEASED GASES AND/OR ACID.
A RESISTOR IN THE ELECTRONIC PANEL CLUSTER MAY BE SUBJECTED TO AN ELECTRICAL CURRENT OVERLOAD DUE TO FAILURE OF A SWITCHING TRANSISTOR. CONSEQUENCE OF DEFECT: THE OVERHEATED RESISTOR COULD IGNITE AND START AN INSTRUMENT PANEL FIRE.
A RESISTOR IN THE ELECTRONIC PANEL CLUSTER MAY BE SUBJECTED TO AN ELECTRICAL CURRENT OVERLOAD DUE TO FAILURE OF A SWITCHING TRANSISTOR. CONSEQUENCE OF DEFECT: THE OVERHEATED RESISTOR COULD IGNITE AND START AN INSTRUMENT PANEL FIRE.
AN ENGINE COMPARTMENT FUEL HOSE ROUTED TO THE FUEL SYSTEM PRESSURE REGULATOR MAY HAVE AN INADEQUATELY TIGHTENED HOSE CLAMP. CONSEQUENCE OF DEFECT: THE FUEL HOSE COULD LEAK AND RESULT IN AN ENGINE COMPARTMENT FIRE.
AN ENGINE COMPARTMENT FUEL HOSE ROUTED TO THE FUEL SYSTEM PRESSURE REGULATOR MAY HAVE AN INADEQUATELY TIGHTENED HOSE CLAMP. CONSEQUENCE OF DEFECT: THE FUEL HOSE COULD LEAK AND RESULT IN AN ENGINE COMPARTMENT FIRE.
AN ENGINE COMPARTMENT FUEL HOSE ROUTED TO THE FUEL SYSTEM PRESSURE REGULATOR MAY HAVE AN INADEQUATELY TIGHTENED HOSE CLAMP. CONSEQUENCE OF DEFECT: THE FUEL HOSE COULD LEAK AND RESULT IN AN ENGINE COMPARTMENT FIRE.
REQUIRED FRONT CENTER SEAT BELT ASSEMBLY WAS OMITTED. VEHICLES ARE NOT IN COMPLIANCE WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD 209, SEAT BELT ASSEMBLIES.
THE POTENTIAL FOR FUEL LEAKAGE EXISTS IN THE ENGINE COMPARTMENT AT THE FUEL RESERVOIR SEAM AND ITS HOSE CONNECTIONS. THE FUEL RESERVOIR IS A SILVER COLORED CAN MOUNTED TO THE AIR CLEANER.
SOME HOOD LATCH ASSEMBLIES MAY HAVE BEEN IMPROPERLY REPAIRED AT THE FACTORY, OR INCORRECT FASTENERS WERE USED. HOOD LATCH ATTACHMENT WILL NOT BE STRONG ENOUGH AND WILL LIKELY WEAKEN THE INNER HOOD PANEL.
LOCATION OF HYDRAULIC BRAKE TUBE TO BOTH REAR WHEELS CAUSES INTERFERENCE AND CHAFING BETWEEN THE TUBES AND REAR SUSPENSION TRAILING ARM PIVOT BRACKETS.
HYDRAULIC BRAKE TUBING ROUTED TO THE LEFT REAR WHEEL BRAKE SYSTEM MAY HAVE BEEN BENT OUT OF SHAPE DURING ASSEMBLY AND COULD CHAFE AGAINST THE EXHAUST SYSTEM HANGER BOLT.
HYDRAULIC BRAKE TUBING ROUTED TO THE LEFT REAR WHEEL BRAKE SYSTEM MAY HAVE BEEN BENT OUT OF SHAPE DURING ASSEMBLY AND COULD CHAFE AGAINST THE EXHAUST SYSTEM HANGER BOLT.
THE TRAVEL COMPUTER SYSTEM WIRING, ON THE INVOLVED VEHICLES, MAY BE IMPROPERLY CONNECTED. THIS CONDITION CAN CAUSE DAMAGE TO INTERNAL COMPONENTS.
THE TRAVEL COMPUTER SYSTEM WIRING, ON THE INVOLVED VEHICLES, MAY BE IMPROPERLY CONNECTED. THIS CONDITION CAN CAUSE DAMAGE TO INTERNAL COMPONENTS.
THE INVOLVED VEHICLES MAY BE EQUIPPED WITH AN ELECTRICAL FUEL FILLER DOOR RELEASE WHICH IS ACTIVATED THROUGH A COILED CURRENT CARRYING WIRE (A SOLENOID). A SHORT IN THE SOLENOID COULD CAUSE SPARKING AT THE ATTACHING SCREWS OF THE SOLENOID.
ON THE INVOLVED VEHICLES, IMPROPER ROUTING OF THE HYDRAULIC BRAKE TUBE COULD CAUSE IT TO CHAFE AGAINST THE PARK BRAKE CABLES. EVENTUALLY, THE BRAKE TUBE MAY FAIL AND BRAKE FLUID LEAKAGE MAY OCCUR.
THE BRAKE HYDRAULIC SYSTEM BAY BE EQUIPPED WITH BRAKE FLUID CONTAINING AN EXCESS OF WATER.
CLAMP BOLTS INSTALLED ON CERTAIN VEHICLES MAY CONTAIN CRACKS. EVENTUALLY THESE BOLTS MAY BREAK THROUGH, CAUSING SEPARATION OF THE BALL JOINT FROM THE STEERING KNUCKLE.
CLAMP BOLTS INSTALLED ON CERTAIN VEHICLES MAY CONTAIN CRACKS. EVENTUALLY THESE BOLTS MAY BREAK THROUGH, CAUSING SEPARATION OF THE BALL JOINT FROM THE STEERING KNUCKLE.
THE AUTOMATIC SPEED CONTROL SWITCH MAY STICK IN THE RESUME POSITION RESTRICTING RETURN MOVEMENT. THIS WILL NOT ALLOW THE NORMAL BRAKE PEDAL OPERATION TO DEACTIVATE THE SYSTEM.
THE AUTOMATIC SPEED CONTROL SWITCH MAY STICK IN THE RESUME POSITION RESTRICTING RETURN MOVEMENT. THIS WILL NOT ALLOW THE NORMAL BRAKE PEDAL OPERATION TO DEACTIVATE THE SYSTEM.
THE AUTOMATIC SPEED CONTROL SWITCH MAY STICK IN THE RESUME POSITION RESTRICTING RETURN MOVEMENT. THIS WILL NOT ALLOW THE NORMAL BRAKE PEDAL OPERATION TO DEACTIVATE THE SYSTEM.
THE AUTOMATIC SPEED CONTROL SWITCH MAY STICK IN THE RESUME POSITION RESTRICTING RETURN MOVEMENT. THIS WILL NOT ALLOW THE NORMAL BRAKE PEDAL OPERATION TO DEACTIVATE THE SYSTEM.
THE AUTOMATIC SPEED CONTROL SWITCH MAY STICK IN THE RESUME POSITION RESTRICTING RETURN MOVEMENT. THIS WILL NOT ALLOW THE NORMAL BRAKE PEDAL OPERATION TO DEACTIVATE THE SYSTEM.
THE AUTOMATIC SPEED CONTROL SWITCH MAY STICK IN THE RESUME POSITION RESTRICTING RETURN MOVEMENT. THIS WILL NOT ALLOW THE NORMAL BRAKE PEDAL OPERATION TO DEACTIVATE THE SYSTEM.
THE AUTOMATIC SPEED CONTROL SWITCH MAY STICK IN THE RESUME POSITION RESTRICTING RETURN MOVEMENT. THIS WILL NOT ALLOW THE NORMAL BRAKE PEDAL OPERATION TO DEACTIVATE THE SYSTEM.
THE AUTOMATIC SPEED CONTROL SWITCH MAY STICK IN THE RESUME POSITION RESTRICTING RETURN MOVEMENT. THIS WILL NOT ALLOW THE NORMAL BRAKE PEDAL OPERATION TO DEACTIVATE THE SYSTEM.
