Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
CERTAIN DELPHI FUEL PRESSURE REGULATORS, P/NOS. FP10020-11B1, FP10026-11B1, AND FP10027-11B1, SOLD AFTER JANUARY 9, 2007, AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE UNIVERSAL PRESSURE REGULATORS (UPR) WERE PRODUCED WITHOUT AN O'RING AND RETAINER.
CERTAIN PASSENGER VEHICLES AND MINI VANS HAVE LOWER PINION BEARINGS IN THE POWER RACK AND PINION ASSEMBLY IN WHICH THE RETAINER TABS WERE NOT CRIMPED PROPERLY. THESE AND SOME OTHER RETAINERS USED IN VEHICLES ASSEMBLED BETWEEN JANUARY 1, 1996 AND OCTOBER 31, 1997, COULD FAIL AND PERMIT THE BALL BEARINGS TO ESCAPE.
THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH THE SAFETY ACT. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. VEHICLE DESCRIPTION: MINIVANS EQUIPPED WITH FRONT BUCKET SEATS. THE FRONT SEAT RECLINER MECHANISM LOWER BOLTS CAN LOOSEN. A LOOSE BOLT COULD FATIGUE AND BREAK, RESULTING IN THE SEAT BACK FALLING REARWARD.
THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH THE SAFETY ACT. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. VEHICLE DESCRIPTION: MINIVANS EQUIPPED WITH FRONT BUCKET SEATS. THE FRONT SEAT RECLINER MECHANISM LOWER BOLTS CAN LOOSEN. A LOOSE BOLT COULD FATIGUE AND BREAK, RESULTING IN THE SEAT BACK FALLING REARWARD.
VEHICLE DESCRIPTION: PASSENGER VEHICLES AND MINI VANS ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE FOLLOWING STATES: CONNECTICUT, ILLINOIS, INDIANA, MAINE, MASSACHUSETTS, MICHIGAN, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT AND WISCONSIN. THE REAR CRADLE BOLTS PULL THROUGH THE RETAINERS DUE TO CORROSION OF THE RETAINER. IF BOTH BOLTS PULL THROUGH, THE REAR CRADLE WOULD NOT LONGER BE SUPPORTED AT THESE MOUNTING LOCATIONS AND THE STEERING INTERMEDIATE SHAFT CAN SEPARATE FROM THE STEERING GEAR.
VEHICLE DESCRIPTION: PASSENGER VEHICLES AND MINI VANS ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE FOLLOWING STATES: CONNECTICUT, ILLINOIS, INDIANA, MAINE, MASSACHUSETTS, MICHIGAN, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT AND WISCONSIN. THE REAR CRADLE BOLTS PULL THROUGH THE RETAINERS DUE TO CORROSION OF THE RETAINER. IF BOTH BOLTS PULL THROUGH, THE REAR CRADLE WOULD NOT LONGER BE SUPPORTED AT THESE MOUNTING LOCATIONS AND THE STEERING INTERMEDIATE SHAFT CAN SEPARATE FROM THE STEERING GEAR.
VEHICLE DESCRIPTION: PASSENGER VEHICLES MANUFACTURED FROM AUGUST 1991 THROUGH JULY 1995. THE TRANSMISSION OIL COOLER LINE CAN SEPARATE WHEN THE VEHICLE IS OPERATED IN LOW TEMPERATURES IN COMBINATION WITH HIGH TRANSMISSION LOADS.
VEHICLE DESCRIPTION: PASSENGER VEHICLES MANUFACTURED FROM AUGUST 1991 THROUGH JULY 1995. THE TRANSMISSION OIL COOLER LINE CAN SEPARATE WHEN THE VEHICLE IS OPERATED IN LOW TEMPERATURES IN COMBINATION WITH HIGH TRANSMISSION LOADS.
VEHICLE DESCRIPTION: PASSENGER VEHICLES MANUFACTURED FROM AUGUST 1991 THROUGH JULY 1995. THE TRANSMISSION OIL COOLER LINE CAN SEPARATE WHEN THE VEHICLE IS OPERATED IN LOW TEMPERATURES IN COMBINATION WITH HIGH TRANSMISSION LOADS.
VEHICLE DESCRIPTION: PASSENGER VEHICLES MANUFACTURED FROM AUGUST 1991 THROUGH JULY 1995. THE TRANSMISSION OIL COOLER LINE CAN SEPARATE WHEN THE VEHICLE IS OPERATED IN LOW TEMPERATURES IN COMBINATION WITH HIGH TRANSMISSION LOADS.
THESE VEHICLES WERE ASSEMBLED WITH THROTTLE CABLE SUPPORT BRACKETS THAT COULD CONTACT THE THROTTLE LEVER SYSTEM AND INHIBIT THE THROTTLE RETURN. THIS DOES NOT MEET THE REQUIREMENTS OF FMVSS NO. 124, ACCELERATOR CONTROL SYSTEMS.
IMPROPERLY MANUFACTURED BRAKE PEDAL ARM CAUSES THE BRAKE PEDAL ARM TO FRACTURE DURING BRAKING.
THE SECOND ROW, RIGHT HAND SHOULDER BELT CAN BECOME PINCHED BETWEEN THE SEAT AND THE DOOR FRAME PILLAR TRIM. THE SHOULDER BELT MAY NOT RETRACT PROPERLY, WHICH DOES NOT COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 208, OCCUPANT CRASH PROTECTION. THE 1994 VEHICLES HAVE AN OPTIONAL INTEGRAL (BUILT IN) CHILDSEAT INSTALLED NEXT TO THE POWER SLIDING SIDE DOOR. THE 1993 INVOLVED VEHICLES HAVE STANDARD SEATS IN THAT SAME POSITION.
THE SECOND ROW, RIGHT HAND SHOULDER BELT CAN BECOME PINCHED BETWEEN THE SEAT AND THE DOOR FRAME PILLAR TRIM. THE SHOULDER BELT MAY NOT RETRACT PROPERLY, WHICH DOES NOT COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 208, OCCUPANT CRASH PROTECTION. THE 1994 VEHICLES HAVE AN OPTIONAL INTEGRAL (BUILT IN) CHILDSEAT INSTALLED NEXT TO THE POWER SLIDING SIDE DOOR. THE 1993 INVOLVED VEHICLES HAVE STANDARD SEATS IN THAT SAME POSITION.
THE THIRD ROW SAFETY BELT RETRACTORS MAY BE INSTALLED INCORRECTLY AND MAY LOCK-UP WHEN THE VEHICLE IS ON SLOPES OF LESS THAN 15 DEGREES, WHICH DOES NOT COMPLY WITH FMVSS NO. 209, SEAT BELT ASSEMBLIES.
VEHICLE FAILS TO CONFORM TO FMVSS NO. 209, SEAT BELT ASSEMBLIES. THE SAFETY BELT OF THE LEFT THIRD ROW SEAT ON THE SIX PASSENGER VAN AND THE CENTER SECOND ROW SEAT OF THE SEVEN PASSENGER VAN MAY LOCK UP AND CANNOT BE WITHDRAWN FROM THE RETRACTOR.
VEHICLE FAILS TO CONFORM TO FMVSS NO. 209, SEAT BELT ASSEMBLIES. THE SAFETY BELT OF THE LEFT THIRD ROW SEAT ON THE SIX PASSENGER VAN AND THE CENTER SECOND ROW SEAT OF THE SEVEN PASSENGER VAN MAY LOCK UP AND CANNOT BE WITHDRAWN FROM THE RETRACTOR.
THE SAFETY BELT RETRACTORS FOR THE REAR CENTER POSITION ARE MISSING A PAWL SPRING AND IN CASE OF AN ACCIDENT, WILL ALLOW THE SAFETY BELT WEBBING TO EXTEND BEYOND THE MINIMUM REQUIREMENTS OF FMVSS NO. 208, OCCUPANT CRASH PROTECTION.
A RIGHT HAND SEAT/SHOULDER BELT RETRACTOR MAY HAVE BEEN INSTALLED IN THE SECOND ROW LEFT HAND SEAT POSITION (DIRECTLY BEHIND DRIVER).
THE REAR MODULAR SEAT FRAME HOLD-DOWN HOOKS MAY NOT MEET THE REQUIRED PULL FORCE AT THE REAR SET ANCHORAGE.
