Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
THE AUTOMATIC COOLER LINE HOSES ON SOME OF THE SUSPECT VEHICLES MAY CONTAIN MATERIAL VOIDS, WHICH COMBINED WITH A HIGH THERMAL EXPANSION AT ELEVATED TEMPERATURES, COULD RESULT IN HOSE FAILURE AND TRANSMISSION FLUID LEAKAGE.
THE INVOVLED VEHICLES FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 201, OCCUPANT PROTECTION IN INTERIOR IMPACTS. INCORRECT HEAD RESTRAINTS MAY HAVE BEEN INSTALLED.
UNDER CERTAIN DRIVING CONDITIONS, THESE VEHICLES CAN EXPERIENCE TEMPERATURES IN THE FRONT WHEEL OUTER BEARING AREA WHICH CAN AFFECT THE WHEEL BEARING GREASE. THIS CAN RESULT IN INADEQUATE LUBRICATION OF THE BEARING. THIS CONDITION MAY BE FURTHER AGGRAVATED BY IMPROPER ADJUSTMENT OF THE FRONT WHEEL SPINDLE NUT.
A CHILD COULD OPEN THE REAR SIDE COMPARTMENT DOOR AND ENTER THIS COMPARTMENT. THE CHILD COULD BECOME ENTRAPPED IF THE DOOR WERE TO CLOSE, AS IT CANNOT BE UNLATCHED FROM THE INSIDE.
A CHILD COULD OPEN THE REAR SIDE COMPARTMENT DOOR AND ENTER THIS COMPARTMENT. THE CHILD COULD BECOME ENTRAPPED IF THE DOOR WERE TO CLOSE, AS IT CANNOT BE UNLATCHED FROM THE INSIDE.
A CHILD COULD OPEN THE REAR SIDE COMPARTMENT DOOR AND ENTER THIS COMPARTMENT. THE CHILD COULD BECOME ENTRAPPED IF THE DOOR WERE TO CLOSE, AS IT CANNOT BE UNLATCHED FROM THE INSIDE.
THE CARBURETOR FUEL FEED HOSE MAY NOT HAVE BEEN PROPERLY POSITIONED DURING ASSEMBLY. AS A RESULT THE HOSE COULD COME IN CONTACT WITH OR BE TOO CLOSE TO THE ENGINE EMISSION EXHAUST SYSTEM GAS RECIRCULATION VALVE. THIS CAN CAUSE THE HOSE TO RUPTURE.
ON THE INVOLVED VEHICLES THE BRAKE STOPLIGHT AND CRUISE CONTROL SWITCH WHICH IS OPERATED BY THE BRAKE PEDAL MAY HAVE BEEN ASSEMBLED WITH AN INCORRECT LUBRICANT ON THE ACTUATING PLUNGER. THIS CAN CAUSE THE REAR BRAKE STOPLIGHTS TO BECOME INOPERATIVE AND THE CRUISE CONTROL, IF ACTIVATED, TO STAY ELECTRICALLY ENGAGED.
THE INVOLVED VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 106, BRAKE HOSES. THESE VEHICLES WERE MANUFACTURED WITH GASOLINE FUEL HOSES IN PLACE OF THE VACUUM HOSE BETWEEN THE INTAKE MANIFOLD AND CARBON CANISTER IN THE POWER BRAKE VACUUM LINE. SHOULD THIS HOSE RUPTURE, IT WOULD RESULT IN A LOSS OF POWER ASSIST TO THE BRAKE SYSTEM. THIS WOULD INCREASE THE DISTANCE REQUIRED TO STOP THE VEHICLE.
THE INVOLVED VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 106, BRAKE HOSES. THESE VEHICLES WERE MANUFACTURED WITH GASOLINE FUEL HOSES IN PLACE OF THE VACUUM HOSE BETWEEN THE INTAKE MANIFOLD AND CARBON CANISTER IN THE POWER BRAKE VACUUM LINE. SHOULD THIS HOSE RUPTURE, IT WOULD RESULT IN A LOSS OF POWER ASSIST TO THE BRAKE SYSTEM. THIS WOULD INCREASE THE DISTANCE REQUIRED TO STOP THE VEHICLE.
THE ENGINE OIL PRESSURE SWITCH MAY CAUSE A RANDOM INTERNAL ELECTRICAL SHORT WHICH COULD RESULT IN THE ENGINE STARTING BY ITSELF WHEN THE IGNITION SWITCH IS TURNED TO THE ON POSITION.
THE FRONT SUSPENSION COIL SPRING MAY HAVE A LARGER THAN DESIRED INSIDE DIAMETER OF THE LOWER COIL WHERE IT RESTS ON THE SPRING SEAT. THIS COULD ALLOW THE SPRING TO BE FORCED OVER THE LOWER SPRING SEAT DUE TO SUSPENSION FORCES.
AN INCORRECT FLUID WAS USED AS AN ASSEMBLY AID (LUBRICATION) DURING INSTALLATION OF THE PISTON SEAL IN FRONT BRAKE CALIPERS WHICH WERE INSTALLED IN 10.5 X 1 DISC BRAKE ASSEMBLIES USED ON A SERIES CARS. THE INCORRECT FLUID ATTACKS THE PISTON SEAL AND CAUSES THEM TO SWELL AND DETERIORATE.
THERE IS A POTENTIAL FOR INTERFERENCE BETWEEN THE CLUTCH CONTROL CABLE AND BRAKE PIPE IN THE MASTER CYLINDER. THIS CAN RESULT IN RUBBING CONTACT WHEN THE CLUTCH PEDAL IS OPERATED. ALSO, THE BRAKE PIPE CLEARANCE TO THE TRANSMISSION CASE MAY BE INADEQUATE. IF THIS CONDITION EXISTS, IT COULD EVENTUALLY RESULT IN A FAILURE IN THE BRAKE PIPE, CAUSING LOSS OF BRAKE FLUID AND PARTIAL LOSS OF BRAKING ACTION.
FUEL HOSES MAY BE INCORRECTLY POSITIONED AND CONTACT THE RIGHT FRONT DRIVE AXLE BOOT DURING VEHICLE OPERATION. AFTER A PERIOD OF TIME, THE ROTATING BOOT COULD WEAR A HOLE IN THE FUEL HOSE, RESULTING IN FULE LEAKAGE.
OPERATION OF THE VEHICLE IN A MANNER WHICH PRODUCES HARD BOTTOMING OUT OF THE FRONT SUSPENSION MAY CAUSE DEFORMATION OF THE LEFT ENGINE MOUNT SUPPORT STRUCTURE AND ALLOW THE ENGINE MOUNT BRACKET TO CONTACT THE STEERING PITMAN ARM OR STEERING LINKAGE.
OPERATION OF THE VEHICLE IN A MANNER WHICH PRODUCES HARD BOTTOMING OUT OF THE FRONT SUSPENSION MAY CAUSE DEFORMATION OF THE LEFT ENGINE MOUNT SUPPORT STRUCTURE AND ALLOW THE ENGINE MOUNT BRACKET TO CONTACT THE STEERING PITMAN ARM OR STEERING LINKAGE.
VEHICLES DO NOT COMPLY TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 207, ANCHORAGE OF SEATS. THE LOCK BAR IN THE FRONT SEAT ADJUSTER ASSEMBLIES MAY NOT ENGAGE PROPERLY AND THE ABILITY OF THE SEAT ADJUSTER TO MAINTAIN THE SEAT IN A LATCHED POSITION DURING AN ACCIDENT MAY BE REDUCED.
VEHICLES FAIL TO COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 105, HYDRAULIC BRAKE SYSTEMS. AN INCORRECT PARKING BRAKE ADJUSTING SPRING WAS INSTALLED ON CERTAIN VEHICLES. THIS MAY CAUSE INTERFERENCE WHEN ATTEMPTING TO APPLY THE PARKING BRAKES.
THE TRANSMISSIONS HAVE BEEN ASSEMBLED WITH A HIGHER THAN NORMAL RETURN SPRING LOAD ON THE TRANSMISSION LOCKING PAWL. WHEN THE PARK POSITION IS SELECTED WITH THE TRANSMISSION SHIFT LEVER, THE PARKING PAWL MAY NOT ENGAGE.
A GASKET WAS MISTAKENLY PLACED BETWEEN THE BRAKE MASTER CYLINDER AND THE POWER BOOST WHICH PREVENTED THE TWO PARTS FROM FITTING TOGETHER PROPERLY. DAMAGE MAY HAVE RESULTED TO THE MOUNTING EARS OF THE MASTER CYLINDER AND THE HYDRO-BOOST. THIS CONDITION COULD LEAD TO BRAKE FAILURE.
A GASKET WAS MISTAKENLY PLACED BETWEEN THE BRAKE MASTER CYLINDER AND THE POWER BOOST WHICH PREVENTED THE TWO PARTS FROM FITTING TOGETHER PROPERLY. DAMAGE MAY HAVE RESULTED TO THE MOUNTING EARS OF THE MASTER CYLINDER AND THE HYDRO-BOOST. THIS CONDITION COULD LEAD TO BRAKE FAILURE.
UNDER CERTAIN DRIVING CONDITIONS, INCLUDING EXTENDED SEVERE BRAKING, THE WHEEL BEARING AREA MAY ENCOUNTER TEMPERATURES THAT CAN CAUSE THE GREASE TO MIGRATE OUT OF THE BEARING AREA. THIS WILL REDUCE THE AMOUNT OF LUBRICATION AVAILABLE TO THE BEARINGS AND RESULT IN FRONT WHEEL BEARING FAILURE AND SPINDLE DAMAGE.
THE REAR AXLE SHAFTS MAY CONTAIN A FLAW IN THE METAL. THIS FLAW COULD ALLOW THE SHAFT TO BREAK AND THE TIRE AND WHEEL ASSEMBLY TO SEPARATE.
THE HUB PORTION OF THE FAN BLADE ASSEMBLY COULD CRACK DUE TO HIGH STRESS LEVELS GENERATED DURING ENGINE OPERATING CONDITIONS. EVENTUALLY, THE BLADE COULD BREAK APART AT THE HUB AND BLADE PIECES COULD BE PROPELLED INTO THE ENGINE. IF THE HOOD IS OPEN WHILE THE ENGINE IS RUNNING, THE FRAGMENTS WOULD BE FREE TO FLY FROM THE VEHICLE.
THE HUB PORTION OF THE FAN BLADE ASSEMBLY COULD CRACK DUE TO HIGH STRESS LEVELS GENERATED DURING ENGINE OPERATING CONDITIONS. EVENTUALLY, THE BLADE COULD BREAK APART AT THE HUB AND BLADE PIECES COULD BE PROPELLED INTO THE ENGINE. IF THE HOOD IS OPEN WHILE THE ENGINE IS RUNNING, THE FRAGMENTS WOULD BE FREE TO FLY FROM THE VEHICLE.
THE HUB PORTION OF THE FAN BLADE ASSEMBLY COULD CRACK DUE TO HIGH STRESS LEVELS GENERATED DURING ENGINE OPERATING CONDITIONS. EVENTUALLY, THE BLADE COULD BREAK APART AT THE HUB AND BLADE PIECES COULD BE PROPELLED INTO THE ENGINE. IF THE HOOD IS OPEN WHILE THE ENGINE IS RUNNING, THE FRAGMENTS WOULD BE FREE TO FLY FROM THE VEHICLE.
THE INTERMEDIATE SHAFT COUPLING ON THE INVOLVED VEHICLES MAY HAVE BEEN MACHINED OVERSIZED IN THE SERRATION AREA WHERE IT ATTACHES TO THE STEERING COLUMN. THIS WOULD PREVENT THE COUPLING FROM PROPERLY TIGHTENING ON THE SHAFT WHEN THE CLAMP AND PINCH BOLT WERE INSTALLED.
THE REAR WHEEL MOUNTING BOLTS ON THE AFFECTED VEHICLES, ARE BRITTLE AND THEREFORE MAY FRACTURE. THIS BRITTLENESS IS DUE TO IMPROPER HEAT TREATMENT DURING MANUFACTURE. IF THE BOLTS BREAK, THE TIRE AND WHEEL ASSEMBLY MAY SEPARATE FROM THE VEHICLE.
THE REAR AXLE SHAFTS ON THE INVOLVED VEHICLES MAY HAVE A FLAW IN THE METAL. AS A RESULT, THE SHAFT MAY BREAK, WHICH WOULD ALLOW THE TIRE AND WHEEL ASSEMBLY TO SEPARATE FROM THE VEHICLE.
