Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
ONE OR BOTH ABS HYDRAULIC UNIT MOUNTING BOLTS MAY NOT BE PROPERLY SEATED AND COULD LOOSEN.
THE PARKING BRAKE CABLE MAY BE DISCONNECTED FROM THE LEFT REAR BRAKE CALIPER.
FUEL FEED HOSE COULD LEAK AT THE COUPLING ON THE ENGINE END OF THE HOSE ASSEMBLY.
FUEL ROLLOVER VALVE ASSEMBLY MAY NOT HAVE BEEN INSTALLED.
EXCESSIVE ACCELERATOR CABLE FRICTION MAY RESTRICT THE CABLES FREE MOVEMENT BETWEEN THE ACCELERATOR PEDAL AND THE THROTTLE BODY.
EXCESSIVE ACCELERATOR CABLE FRICTION MAY RESTRICT THE CABLES FREE MOVEMENT BETWEEN THE ACCELERATOR PEDAL AND THE THROTTLE BODY.
INSUFFICIENT CLEARANCE BETWEEN THE POWER STEERING PUMP PRESSURE HOSE ASSEMBLY AND THE TRANSMISSION GOVERNOR/SPEED SENSOR CONNECTOR COULD CAUSE ABRASION OF THE HOSE.
INSUFFICIENT CLEARANCE BETWEEN THE POWER STEERING PUMP PRESSURE HOSE ASSEMBLY AND THE TRANSMISSION GOVERNOR/SPEED SENSOR CONNECTOR COULD CAUSE ABRASION OF THE HOSE.
A CLIP ON THE SHIFTER MECHANISM INSIDE THE CONSOLE MAY BECOME DISLODGED PREVENTING INDICATION OF THE CORRECT GEAR SELECTION UNDER CONDITIONS OF DARKNESS.
THE FUEL FEED OR FUEL RETURN HOSE AT THE ENGINE MAY RUB AGAINST A SHIFT LEVER ON THE 5 SPEED TRANSAXLE.
THE FUEL FEED AND/OR RETURN HOSE/PIPE ASSEMBLIES COULD CRACK OR SEPARATE, ALLOWING FUEL TO LEAK INTO THE UNDERHOOD AREA.
INTERNAL CORROSION OF PULSAIR CHECK VALVE ASSEMBLY COULD PERMIT EXHAUST GAS TO MELT THE PLASTIC SHUT OFF VALVE AND DRAW VALVE PIECES INTO THE AIR CLEANER AND THROTTLE BODY.
MANUAL VALVE LINK IN THE TRANSMISSION MAY HAVE BEEN IMPROPERLY FORMED.
MANUAL VALVE LINK IN THE TRANSMISSION MAY HAVE BEEN IMPROPERLY FORMED.
AN IN LINE FUSIBLE LINK MAY MELT DOWN AND CAUSE A FIRE.
AN IN LINE FUSIBLE LINK MAY MELT DOWN AND CAUSE A FIRE.
SMALL CRACKS MAY DEVELOP IN THE BODY PILLAR AROUND THE DOOR STRIKER BOLT HOLE.
SMALL CRACKS MAY DEVELOP IN THE BODY PILLAR AROUND THE DOOR STRIKER BOLT HOLE.
THE ANTI LOCK BRAKE SYSTEM (ABS) PRESSURE/WARNING SWITCH MAY EXHIBIT BRAKE FLUID SEEPAGE WHICH EVENTUALLY CAN LEAD TO LOSS OF THE BRAKE SYSTEM HYDRAULIC PUMP MOTOR. ADDITIONALLY, THE HYDRAULIC PUMP MOTOR AND ABS ELECTRICAL RELAYS MAY HAVE BEEN EXPOSED TO WATER CONTAMINATION DURING VEHICLE ASSEMBLY. THIS CONDITION CAN CAUSE LOSS OF THE HYDRAULIC PUMP MOTOR AND/OR LOSS OF THE ABS FUNCTION.
THE ANTI LOCK BRAKE SYSTEM (ABS) PRESSURE/WARNING SWITCH MAY EXHIBIT BRAKE FLUID SEEPAGE WHICH EVENTUALLY CAN LEAD TO LOSS OF THE BRAKE SYSTEM HYDRAULIC PUMP MOTOR. ADDITIONALLY, THE HYDRAULIC PUMP MOTOR AND ABS ELECTRICAL RELAYS MAY HAVE BEEN EXPOSED TO WATER CONTAMINATION DURING VEHICLE ASSEMBLY. THIS CONDITION CAN CAUSE LOSS OF THE HYDRAULIC PUMP MOTOR AND/OR LOSS OF THE ABS FUNCTION.
THE METAL FLOOR PAN ANCHOR BAR COULD FATIGUE AND BREAK AROUND THE LEFT FRONT OUTER SEAT ADJUSTER STUD OF THE DRIVERS SEAT, ALLOWING THE STUD TO SEPARATE FROM THE FLOOR PAN ANCHOR BAR.
THE METAL FLOOR PAN ANCHOR BAR COULD FATIGUE AND BREAK AROUND THE LEFT FRONT OUTER SEAT ADJUSTER STUD OF THE DRIVERS SEAT, ALLOWING THE STUD TO SEPARATE FROM THE FLOOR PAN ANCHOR BAR.
POOR BOND ADHESION BETWEEN THE WINDSHIELD GLASS AND MOUNTING COULD ALLOW THE WINDSHIELD TO SEPARATE DURING A 30 MPH FRONTAL BARRIER TEST REQUIRED BY FMVSS 212.
CONSOLE FRONT COMPARTMENT DOOR MAY NOT REMAIN CLOSED DURING LOAD FORCES THAT MAY BE EXPERIENCED IN A CRASH AS REQUIRED BY FMVSS 201.
THERE MAY NOT BE ENOUGH CLEARANCE BETWEEN THE POWER STEERING PUMP RETURN HOSE AND THE ENGINE EXHAUST MANIFOLD. CONSEQUENCE OF DEFECT: HOSE COULD OVERHEAT, RESULTING IN A HOLE AND FLUID LEAK, AND A POSSIBLE ENGINE COMPARTMENT FIRE WITHOUT PRIOR WARNING.
PARKING BRAKE LEVER MECHANISMS MAY NOT PROPERLY ENGAGE WHEN APPLIED AS REQUIRED BY FMVSS 105. CONSEQUENCE OF DEFECT: VEHICLE COULD UNEXPECTEDLY ROLL AWAY UNCONTROLLED, WHICH COULD RESULT IN A VEHICLE CRASH.
THE LEFT AND RIGHT REAR LOWER CONTROL ARM BALL JOINT STUD TO KNUCKLE ATTACHMENT MAY HAVE BEEN INADEQUATELY TIGHTENED. CONSEQUENCE OF DEFECT: THIS COULD ALLOW THE REAR LOWER CONTROL ARM BALL JOINT STUD TO LOOSEN AT THE KNUCKLE ATTACHMENT. A LOOSE BALL JOINT STUD COULD EVENTUALLY BREAK AND SEPARATE FROM THE KNUCKLE. SEPARATION COULD CAUSE A LOSS OF VEHICLE CONTROL WHICH COULD RESULT IN A VEHICLE CRASH WITHOUT PRIOR WARNING.
THE SECONDARY HOOD LATCH MAY BE INCORRECTLY ALIGNED, OR MAY EXHIBIT A BINDING CONDITION OF THE LATCH PIVOT. CONSEQUENCE OF DEFECT: THIS CONDITION COULD RESULT IN THE PRIMARY HOOD LATCH NOT BEING COMPLETELY ENGAGED TO THE HOOD, THE HOOD COULD UNEXPECTEDLY OPEN WHILE VEHICLE IS IN MOTION. SHOULD THIS OCCUR, THE HOOD MAY CONTACT THE WINDSHIELD REDUCING THE FORWARD VISION AREA OF THE DRIVER AND A VEHICLE CRASH WITHOUT PRIOR WARNING COULD OCCUR.
THE SECONDARY HOOD LATCH MAY BE INCORRECTLY ALIGNED, OR MAY EXHIBIT A BINDING CONDITION OF THE LATCH PIVOT. CONSEQUENCE OF DEFECT: THIS CONDITION COULD RESULT IN THE PRIMARY HOOD LATCH NOT BEING COMPLETELY ENGAGED TO THE HOOD, THE HOOD COULD UNEXPECTEDLY OPEN WHILE VEHICLE IS IN MOTION. SHOULD THIS OCCUR, THE HOOD MAY CONTACT THE WINDSHIELD REDUCING THE FORWARD VISION AREA OF THE DRIVER AND A VEHICLE CRASH WITHOUT PRIOR WARNING COULD OCCUR.
LEFT HANDED DRIVER'S SIDE SHOULDER BELT ANCHOR PLATE MAY BE UPSIDE DOWN IN LOCK PILLAR SO THAT THE UNTHREADED SLOT OF THE PLATE ALIGNED WITH THE HOLE IN THE LOCK PILLAR. THIS RESULTED IN THE ANCHOR BOLT BEING DRIVEN INTO THE SLOT INSTEAD OF THE THREADED HOLE OF THE ANCHOR PLATE. CONSEQUENCE OF DEFECT: IN A VEHICLE CRASH, BELT ANCHOR BOLT MAY PULL LOOSE FROM ANCHOR PLATE, THUS FAILING TO COMPLY WITH FMVSS 210, SEAT BELT ASSEMBLY ANCHORAGES, AND INCREASES LIKELIHOOD OF INJURY TO OCCUPANT.
