Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
THE HEADLAMP SWITCHES ON THE INVOLVED VEHICLES MAY FAIL WITHOUT WARNING AND CAUSE LOSS OF VEHICLE INSTRUMENT AND ROAD LIGHTS.
THE AIR CONDITIONERS ON SOME VEHICLES CONTAIN BLOWER MOTOR RESISTORS THAT MAY CAUSE OVERHEATING OF THE HOUSING MATERIAL.
THE AIR CONDITIONERS ON SOME VEHICLES CONTAIN BLOWER MOTOR RESISTORS THAT MAY CAUSE OVERHEATING OF THE HOUSING MATERIAL.
THE AIR CONDITIONERS ON SOME VEHICLES CONTAIN BLOWER MOTOR RESISTORS THAT MAY CAUSE OVERHEATING OF THE HOUSING MATERIAL.
THE INVOLVED VEHICLES WERE PRODUCED WITH BRAKE PUSH-ROD TO BRAKE PEDAL RETAINING PINS WHICH WERE NOT HEAT-TREATED AS SPECIFIED. THIS COULD ALLOW THE BRAKE PEDAL TO BECOME DISENGAGED FROM THE PUSH-ROD.
THE INVOLVED VEHICLES WERE PRODUCED WITH BRAKE PUSH-ROD TO BRAKE PEDAL RETAINING PINS WHICH WERE NOT HEAT-TREATED AS SPECIFIED. THIS COULD ALLOW THE BRAKE PEDAL TO BECOME DISENGAGED FROM THE PUSH-ROD.
THE INVOLVED VEHICLES WERE PRODUCED WITH BRAKE PUSH-ROD TO BRAKE PEDAL RETAINING PINS WHICH WERE NOT HEAT-TREATED AS SPECIFIED. THIS COULD ALLOW THE BRAKE PEDAL TO BECOME DISENGAGED FROM THE PUSH-ROD.
THE INVOLVED VEHICLES WERE PRODUCED WITH BRAKE PUSH-ROD TO BRAKE PEDAL RETAINING PINS WHICH WERE NOT HEAT-TREATED AS SPECIFIED. THIS COULD ALLOW THE BRAKE PEDAL TO BECOME DISENGAGED FROM THE PUSH-ROD.
THE INVOLVED VEHICLES WERE PRODUCED WITH BRAKE PUSH-ROD TO BRAKE PEDAL RETAINING PINS WHICH WERE NOT HEAT-TREATED AS SPECIFIED. THIS COULD ALLOW THE BRAKE PEDAL TO BECOME DISENGAGED FROM THE PUSH-ROD.
THE INVOLVED VEHICLES WERE PRODUCED WITH BRAKE PUSH-ROD TO BRAKE PEDAL RETAINING PINS WHICH WERE NOT HEAT-TREATED AS SPECIFIED. THIS COULD ALLOW THE BRAKE PEDAL TO BECOME DISENGAGED FROM THE PUSH-ROD.
THE INVOLVED VEHICLES WERE PRODUCED WITH FRAMES THAT MAY HAVE INADEQUATELY WELDED #2 CROSSMEMBER ASSEMBLIES. THIS COULD OCCUR IF CERTAIN MANUAL WELD OPERATIONS WERE NOT PERFORMED DURING FRAME FABRICATION. SEVERE OPERATING CONDITIONS WHICH MAY OCCUR IN POLICE DUTY, MAY CAUSE CRACKING AROUND THE GUSSET, ALLOWING IT TO SEPARATE FROM THE FRAME.
SOME OF THESE VEHICLES WERE PRODUCED WITH MISINDEXED FRONT BRAKE HOSES WHICH COULD CONTACT A TIRE OR WHEEL IN A FULL-TURN CONDITION. CHAFING AND WEAR TO THE BRAKE HOSE COULD RESULT IN LOSS OF BRAKE FLUID AND FRONT WHEEL BRAKING CAPABILITY.
WITH THE ENGINE OPERATING AT HIGH SPEED, THE PLASTIC ENGINE FAN FINGER GUARDS MAY CONTACT THE ENGINE FAN AND BREAKAGE OF THE GUARD MAY OCCUR. THIS COULD CAUSE FRAGMENTS OF THE FINGER GUARD TO SCATTER.
AN INCORRECT STEERING GEAR FLANGE MAY HAVE BEEN INSTALLED, WHICH MAY SLIP AND CAUSE EVENTUAL LOSS OF STEERING CONTROL.
THE INVOLVED VEHICLES WERE BUILT WITH SAFETY COMPLIANCE CERTIFICATION LABELS THAT CONTAINED INCORRECT GVWR AND GAWR WEIGHT INFORMATION. THE GVWRS COULD BE OVERSTATED BY UP TO 197 LBS., DUE TO AN ERROR IN THE REPORTING OF INCREMENTAL OPTION WEIGHTS USED TO DERIVE THE GVWRS AND GAWRS.
SOME OF THE INVOLVED VEHICLES DO NOT HAVE THE HAIR PIN CLIP USED TO RETAIN THE PUSHROD TO THE BRAKE PEDAL PUSHROD PIN INSTALLED. IF THIS CLIP IS MISSING, THE PUSHROD MAY BECOME DISENGAGED FROM THE BRAKE PEDAL PUSHROD PIN.
THE INVOLVED VEHICLES MAY HAVE BEEN BUILT WITH INCORRECT WELD NUTS THAT ATTACH THE REAR PORTION OF THE FRONT OUTBOARD SEAT TRACK TO THE FLOOR PAN. THE INCORRECT NUTS HAVE AN OVERSIZE DIAMETER AND THREAD, AND UPON FRONT SEAT TRACK ANCHOR BOLT INSTALLATION, THE THREADS MAY HAVE BEEN STRIPPED.
THE INVOLVED VEHICLES MAY HAVE BEEN BUILT WITH INCORRECT WELD NUTS THAT ATTACH THE REAR PORTION OF THE FRONT OUTBOARD SEAT TRACK TO THE FLOOR PAN. THE INCORRECT NUTS HAVE AN OVERSIZE DIAMETER AND THREAD, AND UPON FRONT SEAT TRACK ANCHOR BOLT INSTALLATION, THE THREADS MAY HAVE BEEN STRIPPED.
THE ENGINE COOLING FAN BLADES MAY CRACK UNDER HIGH SPEED OPERATING CONDITIONS. FRAGMENTS MAY SEPARATE AND DAMAGE THE ENGINE COMPONENTS, AND IF THE HOOD IS OPEN AND THE ENGINE IS RUNNING, BLADE FRAGMENTS COULD FLY OUT FROM THE VEHICLE AND INJURE NEARBY PERSONS.
THE ENGINE COOLING FAN BLADES MAY CRACK UNDER HIGH SPEED OPERATING CONDITIONS. FRAGMENTS MAY SEPARATE AND DAMAGE THE ENGINE COMPONENTS, AND IF THE HOOD IS OPEN AND THE ENGINE IS RUNNING, BLADE FRAGMENTS COULD FLY OUT FROM THE VEHICLE AND INJURE NEARBY PERSONS.
THE INVOLVED VEHICLES ARE EQUIPPED WITH FLEXIBLE COOLING FAN BLADES THAT MAY CRACK WHEN SUBJECTED TO HIGH ENGINE SPEED OPERATING CONDITIONS. FAN BLADE CRACKING CAN LEAD TO FRAGMENTS SEPARATING FROM THE FAN.
THE LOWER STEERING SHAFT ASSEMBLIES CONTAIN COUPLING RIVET PINS WHICH WERE NOT RIVETED SECURELY ENOUGH DURING MANUFACTURE. CONSEQUENTLY ONE OR BOTH OF THE PINS COULD LOOSEN FROM THE FLANGE OF THE FLEXIBLE COUPLING DURING VEHICLE OPERATION. IF ONE PIN IS LOOSE, FREE PLAY WOULD RESULT. IF BOTH PINS WORK LOOSE, LOSS OF STEERING CONTROL WOULD OCCUR. ALSO, THE SHAFT ASSEMBLY MAY NOT CONTAIN A METAL REINFORCEMENT BETWEEN ONE OR BOTH OF THE RIVET PINS AND THE RUBBER FLEXIBLE COUPLING. AS A RESULT, THE RUBBER FLEXIBLE COUPLING COULD TEAR AND PRODUCE A NOISE OR LOOSE FEELING IN THE STEERING SYSTEM.
THE FULL SIZE SEDANS WERE EQUIPPED WITH INCORRECT TAIL LAMP SOCKETS AND THE FULL SIZE STATION WAGONS WERE INSTALLED WITH INCORRECT TAIL LAMP AND BACK UP LAMP SOCKETS. THEREFORE THESE VEHICLES FAIL TO COMPLY WITH THE PHOTOMETRIC REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES AND ASSOCIATED EQUIPMENT.
THE INVOLVED VEHICLES CONTAIN EMISSION CONTROL SYSTEMS THAT UTILIZE A PULSE AIR REED VALVE TO PERMIT AIR FLOW FROM THE AIR CLEANER TO THE EXHAUST MANIFOLD ON NEGATIVE PRESSURE PULSATIONS. THESE REED VALVES MAY FAIL UNDER COLD WEATHER CONDITIONS, CAUSING A BACKFLOW OF EXHAUST GAS INTO THE AIR CLEANER AND FUEL INDUCTION SYSTEM ON POSITIVE EXHAUST PULSES. THIS CAUSES AN OVERLY RICH AIR/FUEL MIXTURE, REDUCED FUEL ECONOMY AND REDUCED ENGINE PERFORMANCE. CONTINUED VEHICLE OPERATION MAY RESULT IN ENGINE STALLING OR OVERHEATING OF THE EXHAUST SYSTEM.
THE WINDSHIELD WIPER AND WASHER SYSTEM CONTAINS AN INCORRECT 6 AMP CIRCUIT BREAKER INSTEAD OF THE 8.25 AMP CIRCUIT BREAKER. IF THE SYSTEM IS HEAVILY LOADED, AS IN THE CASE OF A PARTIALLY DRY WINDSHIELD, THE MOTOR CURRENT MAY EXCEED THE 6 AMP BREAKERS CAPACITY. THIS WOULD CAUSE THE BREAKER TO OPEN, WHICH WOULD RESULT IN WIPER/WASHER FAILURE.
THE TILT STEERING COLUMNS ON THE INVOLVED VEHICLES CONTAIN IN-PROCESS TEMPORARY ALIGNMENT PINS RATHER THAN THE PERMANENT PRESS-FIT PIVOT PINS. THE TEMPORARY PINS ARE SLIGHTLY UNDERSIZED AND COULD SEPARATE FROM THE STEERING COLUMN DURING VEHICLE OPERATION. THIS CAN CAUSE STEERING WHEEL LOCKUP.
THE WIPER ARMS COULD SEPARATE FROM THE PIVOT SHAFTS, RENDERING THE WIPERS INOPERATIVE.
THE WIPER ARMS COULD SEPARATE FROM THE PIVOT SHAFTS, RENDERING THE WIPERS INOPERATIVE.
THE WIPER ARMS COULD SEPARATE FROM THE PIVOT SHAFTS, RENDERING THE WIPERS INOPERATIVE.
