Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
THE FLEXIBLE BLADE ENGINE COOLING FAN BLADES MAY CRACK AND BREAK OFF. THIS MAY BE CAUSED BY HIGH BLADE STRESSES THAT CAN RESULT FROM VIBRATION DURING VEHICLE OPERATION.
THE FLEXIBLE BLADE ENGINE COOLING FAN BLADES MAY CRACK AND BREAK OFF. THIS MAY BE CAUSED BY HIGH BLADE STRESSES THAT CAN RESULT FROM VIBRATION DURING VEHICLE OPERATION.
THE FLEXIBLE BLADE ENGINE COOLING FAN BLADES MAY CRACK AND BREAK OFF. THIS MAY BE CAUSED BY HIGH BLADE STRESSES THAT CAN RESULT FROM VIBRATION DURING VEHICLE OPERATION.
THE SHIFT INDICATOR MAY NOT ACCURATELY REFLECT THE SHIFT SELECTOR POSITION. SOME VEHICLES WERE PRODUCED WITH TRANSMISSION CONTROL SELECTOR TUBE RETAINING CLIPS THAT MAY NOT BE HARD ENOUGH. THE CLIP MAY LOOSEN OR FALL OFF, AND THE SELECTOR TUBE MAY BECOME DISPLACED.
THE SHIFT INDICATOR MAY NOT ACCURATELY REFLECT THE SHIFT SELECTOR POSITION. SOME VEHICLES WERE PRODUCED WITH TRANSMISSION CONTROL SELECTOR TUBE RETAINING CLIPS THAT MAY NOT BE HARD ENOUGH. THE CLIP MAY LOOSEN OR FALL OFF, AND THE SELECTOR TUBE MAY BECOME DISPLACED.
THE SHIFT INDICATOR MAY NOT ACCURATELY REFLECT THE SHIFT SELECTOR POSITION. SOME VEHICLES WERE PRODUCED WITH TRANSMISSION CONTROL SELECTOR TUBE RETAINING CLIPS THAT MAY NOT BE HARD ENOUGH. THE CLIP MAY LOOSEN OR FALL OFF, AND THE SELECTOR TUBE MAY BECOME DISPLACED.
THE PORTION OF THE ROOF ABOVE FRAME (RAIL) TO WHICH THE SHOULDER BELT IS ANCHORED MAY HAVE A SLOT THAT CAN COMPROMISE THE STRENGTH OF THE SHOULDER BELT ANCHOR UNDER CERTAIN SEVERE LOADS. (THE SUSPECT AREA IS NOT VISIBLE.) CONSEQUENTLY, SOME VEHICLES INCLUDED IN THIS RECALL MAY NOT MEET THE 3000 POUND ANCHORAGE STRENGTH REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD 210, SEAT BELT ASSEMBLY ANCHORAGES.
THE PORTION OF THE ROOF ABOVE FRAME (RAIL) TO WHICH THE SHOULDER BELT IS ANCHORED MAY HAVE A SLOT THAT CAN COMPROMISE THE STRENGTH OF THE SHOULDER BELT ANCHOR UNDER CERTAIN SEVERE LOADS. (THE SUSPECT AREA IS NOT VISIBLE.) CONSEQUENTLY, SOME VEHICLES INCLUDED IN THIS RECALL MAY NOT MEET THE 3000 POUND ANCHORAGE STRENGTH REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD 210, SEAT BELT ASSEMBLY ANCHORAGES.
SOME OF THESE VEHICLES MAY HAVE BEEN BUILT WITH FUEL TANKS THAT HAVE INADEQUATELY WELDED FRONT SEAMS THAT CAN LEAK.
THE LOWER CONTROL ARMS MAY HAVE BEEN MANUFACTURED FROM STEEL WITH MATERIAL THICKNESS BELOW THE MINIMUM SPECIFICATIONS FOR POLICE DUTY. THIS COULD LEAD TO CRACKS DEVELOPING IN THE CONTROL ARMS, AND EVENTUALLY, THE POSSIBILITY OF FRACTURE OF AN ARM.
THE LOWER CONTROL ARMS MAY HAVE BEEN MANUFACTURED FROM STEEL WITH MATERIAL THICKNESS BELOW THE MINIMUM SPECIFICATIONS FOR POLICE DUTY. THIS COULD LEAD TO CRACKS DEVELOPING IN THE CONTROL ARMS, AND EVENTUALLY, THE POSSIBILITY OF FRACTURE OF AN ARM.
THE PARK LEVER ON THE INVOLVED VEHICLES CONTAINS A DEFECTIVE SPRING WHICH COULD PREVENT AUTOMATIC ENGAGEMENT OF THE PARKING GEAR.
THE PARK LEVER ON THE INVOLVED VEHICLES CONTAINS A DEFECTIVE SPRING WHICH COULD PREVENT AUTOMATIC ENGAGEMENT OF THE PARKING GEAR.
DURING A CRASH BARRIER TEST, THE RUBBER HOSE CONNECTING THE FUEL TANK AND THE METAL FILLER PIPE VENT TUBE WAS CUT, RESULTING IN FUEL LEAKAGE. THE INVOLVED VEHICLES FAIL TO COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 301, FUEL SYSTEM INTEGRITY.
ON THE INVOLVED VEHICLES, A THERMAL LIMITER IN THE BLOWER MOTOR RESISTOR CIRCUIT OF THE AIR CONDITIONER/HEATER ASSEMBLY MAY NOT FUNCTION AS INTENDED. IF THE BLOWER MOTOR BECOMES JAMMED WHEN THE SYSTEM IS OPERATING IN THE MEDIUM-LOW BLOWER SPEED, THE RESISTOR COILS CAN OVERHEAT CAUSING MELTING AND POSSIBLE IGNITION.
ON THE INVOLVED VEHICLES, A THERMAL LIMITER IN THE BLOWER MOTOR RESISTOR CIRCUIT OF THE AIR CONDITIONER/HEATER ASSEMBLY MAY NOT FUNCTION AS INTENDED. IF THE BLOWER MOTOR BECOMES JAMMED WHEN THE SYSTEM IS OPERATING IN THE MEDIUM-LOW BLOWER SPEED, THE RESISTOR COILS CAN OVERHEAT CAUSING MELTING AND POSSIBLE IGNITION.
SOME OF THE SUSPECT VEHICLES MAY HAVE BEEN PRODUCED WITH IMPROPERLY TIGHTENED PROPANE FUEL SYSTEM FITTINGS IN THE ENGINE COMPARTMENT; FUEL LEAKAGE COULD OCCUR.
INCORRECT INFORMATION ON TIRE PLACARDS CONSTITUTES A FAILURE TO COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, TIRE SELECTION AND RIMS. THE INFORMATION CONCERNING TIRE SIZES AND INFLATION PRESSURES IS APPLICABLE TO BOTH TWO AND FOUR DOOR SEDANS. THE STATEMENT COVERS FOUR DOOR BUT FAILS TO SPECIFY TWO DOOR SEDANS.
DUE TO A MANUFACTURING ERROR, CERTAIN FLEXIBLE-BLADE ENGINE COOLING FANS MAY BE SUBJECT TO FATIGUE CRACKING AND BLADE SEPARATION DURING VEHICLE OPERATION.
THE HOUSING PLATES ON THE DRIVER SEAT BACK LATCH RECLINER ASSEMBLIES WERE MANUFACTURED WITH SUBSTANDARD MATERIAL PRODUCTS. THIS TAINTED STEEL WAS USED TO PRODUCE SEATBACK LATCHES FOR BOTH THE RIGHT AND LEFT SIDE SEAT ASSEMBLIES. UNDER CERTAIN CONDITIONS, THE DEFECTIVE HOUSING PLATES MAY DISTORT, ALLOWING THE LOCKING TEETH TO DISENGAGE AND TEAR OFF. THIS PERMITS THE SEATBACK TO PIVOT BACKWARDS.
SOME OF THE INVOLVED VEHICLES HAVE AN ELECTRICALLY UNGROUNDED FUEL INLET. THESE VEHICLES ARE SUBJECT TO STATIC CHARGE ACCUMULATION AT THE FUEL FILLER PIPE OPENING, WHICH CAN OCCUR IF THESE VEHICLES ARE REFUELED FROM AN ELECTRICALLY UNGROUNDED DISPENSING NOZZLE.
SOME VEHICLES EQUIPPED WITH POWER BRAKE BOOSTERS HAVE FRONT AND REAR SHELLS THAT MAY HAVE BEEN IMPROPERLY JOINED. IMPROPERLY JOINED BOOSTER SHELLS MAY SEPARATE EITHER PARTIALLY OR COMPLETELY DURING BRAKE APPLICATION.
SOME VEHICLES EQUIPPED WITH POWER BRAKE BOOSTERS HAVE FRONT AND REAR SHELLS THAT MAY HAVE BEEN IMPROPERLY JOINED. IMPROPERLY JOINED BOOSTER SHELLS MAY SEPARATE EITHER PARTIALLY OR COMPLETELY DURING BRAKE APPLICATION.
CERTAIN VEHICLES MAY NOT MEET APPLICABLE MINIMUM FUEL SPILLAGE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 301, FUEL SYSTEM INTEGRITY. DURING A 30 MPH REAR IMPACT TEST, FUEL SPILLAGE LIMITS WERE EXCEEDED BY VEHICLE.
FUEL MAY POSSIBLY TRAVEL THROUGH THE SPEED CONTROL VACUUM LINES AND INTO THE SPEED CONTROL ACTUATION DEVICE (SERV0). THE FUEL CAN DAMAGE SEALS IN THE ACTUATOR SERVO AND ALLOW VACUUM LEAKS. SUCH A LEAK COULD ACTIVATE THE SPEED CONTROL WITHOUT ANY ACTION ON THE PART OF THE DRIVER. THIS WOULD CAUSE THE VEHICLE TO GRADUALLY ACCELERATE.
THIS IS A MANUFACTURERS NOTICE TO ADVISE OWNERS OF PROPER VEHICLE OPERATION. THE PARKING GEAR MAY NOT BE SECURELY ENGAGED AFTER THE OPERATOR HAS ATTEMPTED TO SHIFT TO PARK. THE VEHICLE MAY APPEAR TO BE IN PARK THOUGH ACTUALLY IN REVERSE. THIS COULD ALLOW THE VEHICLE TO MOVE UNEXPECTEDLY.
THIS IS A MANUFACTURERS NOTICE TO ADVISE OWNERS OF PROPER VEHICLE OPERATION. THE PARKING GEAR MAY NOT BE SECURELY ENGAGED AFTER THE OPERATOR HAS ATTEMPTED TO SHIFT TO PARK. THE VEHICLE MAY APPEAR TO BE IN PARK THOUGH ACTUALLY IN REVERSE. THIS COULD ALLOW THE VEHICLE TO MOVE UNEXPECTEDLY.
THIS IS A MANUFACTURERS NOTICE TO ADVISE OWNERS OF PROPER VEHICLE OPERATION. THE PARKING GEAR MAY NOT BE SECURELY ENGAGED AFTER THE OPERATOR HAS ATTEMPTED TO SHIFT TO PARK. THE VEHICLE MAY APPEAR TO BE IN PARK THOUGH ACTUALLY IN REVERSE. THIS COULD ALLOW THE VEHICLE TO MOVE UNEXPECTEDLY.
THIS IS A MANUFACTURERS NOTICE TO ADVISE OWNERS OF PROPER VEHICLE OPERATION. THE PARKING GEAR MAY NOT BE SECURELY ENGAGED AFTER THE OPERATOR HAS ATTEMPTED TO SHIFT TO PARK. THE VEHICLE MAY APPEAR TO BE IN PARK THOUGH ACTUALLY IN REVERSE. THIS COULD ALLOW THE VEHICLE TO MOVE UNEXPECTEDLY.
THIS IS A MANUFACTURERS NOTICE TO ADVISE OWNERS OF PROPER VEHICLE OPERATION. THE PARKING GEAR MAY NOT BE SECURELY ENGAGED AFTER THE OPERATOR HAS ATTEMPTED TO SHIFT TO PARK. THE VEHICLE MAY APPEAR TO BE IN PARK THOUGH ACTUALLY IN REVERSE. THIS COULD ALLOW THE VEHICLE TO MOVE UNEXPECTEDLY.
