Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
CERTAIN PASSENGER VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 212, WINDSHIELD MOUNTING. THE WINDSHIELDS MAY POTENTIALLY EXHIBIT INCREASED WIND NOISE, WATER LEAKAGE, AND SQUEAKS AND RATTLES.
CERTAIN PASSENGER VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 212, WINDSHIELD MOUNTING. THE WINDSHIELDS MAY POTENTIALLY EXHIBIT INCREASED WIND NOISE, WATER LEAKAGE, AND SQUEAKS AND RATTLES.
ON CERTAIN PASSENGER VEHICLES, THE INTEGRATED AIR BAG MONITOR (IABM) CAN BE CONTAMINATED WITH WATER OR OTHER LIQUIDS AND COULD EXPERIENCE INTERNAL ELECTRICAL SHORTING.
CERTAIN PASSENGER VEHICLES EQUIPPED WITH ADJUSTABLE PADELS ARE BEING RECALLED IN ORDER TO ADJUST THE BRAKE AND ACCELERATOR PEDALS TO A MINIMUM OF 50 MM OF LATERAL SEPARATION. SIMULTANEOUS APPLICATION OF BOTH THE BRAKE AND ACCELERATOR PEDALS COULD RESULT IN AN INCREASE IN ENGINE RPM.
CERTAIN PASSENGER VEHICLES EQUIPPED WITH ADJUSTABLE PADELS ARE BEING RECALLED IN ORDER TO ADJUST THE BRAKE AND ACCELERATOR PEDALS TO A MINIMUM OF 50 MM OF LATERAL SEPARATION. SIMULTANEOUS APPLICATION OF BOTH THE BRAKE AND ACCELERATOR PEDALS COULD RESULT IN AN INCREASE IN ENGINE RPM.
CERTAIN PASSENGER VEHICLES EQUIPPED WITH ADJUSTABLE PADELS ARE BEING RECALLED IN ORDER TO ADJUST THE BRAKE AND ACCELERATOR PEDALS TO A MINIMUM OF 50 MM OF LATERAL SEPARATION. SIMULTANEOUS APPLICATION OF BOTH THE BRAKE AND ACCELERATOR PEDALS COULD RESULT IN AN INCREASE IN ENGINE RPM.
VEHICLE DESCRIPTION: TAURUS/SABLE VEHICLES EQUIPPED WITH 3.0L AND 3.8L ENGINES AND MUSTANG VEHICLES WITH 3.8L AND 5.0L ENGINES. IT IS POSSIBLE FOR THE ENGINE COOLING FAN BEARING TO SEIZE.
THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH THE SAFETY ACT. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. VEHICLE DESCRIPTION: 1995 TAURUS/SABLE PASSENGER VEHICLES EQUIPPED WITH 3.0L AND 3.8L ENGINES AND 1995 FORD MUSTANG VEHICLES WITH 3.8L AND 5.0L ENGINES. IT IS POSSIBLE FOR THE ENGINE COOLING FAN BEARING TO SEIZE.
VEHICLE DESCRIPTION: PASSENGER CARS, SPORT UTILITY VEHICLES, AND LIGHT AND MEDIUM DUTY PICKUP TRUCKS. A SWITCH LOCATED IN THE PLASTIC COVER OF THE WIPER MOTOR GEAR CASE COULD MALFUNCTION AND OVERHEAT, POTENTIALLY RESULTING IN LOSS OF INTERMITTENT WIPER FUNCTION, LOSS OF WIPER PARK FUNCTION, COMPLETE LOSS OF WIPER FUNCTION, OR IGNITION OF THE PLASTIC COVER MATERIAL. SWITCH MALFUNCTION IS MOST LIKELY TO OCCUR WHEN THE INTERMITTENT SETTING OF THE WIPERS IS BEING USED, OR WHEN SNOW OR ICE OBSTRUCTS THE BLADES FROM RETURNING TO THE PARKED POSITION AT THE BOTTOM OF THE WINDSHIELD. THESE VEHICLES WERE BUILT AT THE FOLLOWING ASSEMBLY PLANTS: ATLANTA PLANT FROM 2/11/00 THROUGH 7/31/00; CHICAGO PLANT FROM 2/14/00 THROUGH 8/4/00; KANSAS CITY PLANT FROM 2/26/00 TO 9/4/00; KENTUCKY TRUCK PLANT FROM 2/18/00 TO 8/31/00; MICHIGAN TRUCK PLANT FROM 2/23/00 THROUGH 8/3/00; NORFOLK PLANT FROM 2/21/00 THROUGH 7/27/00; WAYNE STAMPING AND ASSEMBLY PLANT FROM 2/25/00 THROUGH 8/15/00; AND WIXOM PLANT FROM 2/15/00 THROUGH 8/8/00.
VEHICLE DESCRIPTION: PASSENGER CARS, SPORT UTILITY VEHICLES, AND LIGHT AND MEDIUM DUTY PICKUP TRUCKS. A SWITCH LOCATED IN THE PLASTIC COVER OF THE WIPER MOTOR GEAR CASE COULD MALFUNCTION AND OVERHEAT, POTENTIALLY RESULTING IN LOSS OF INTERMITTENT WIPER FUNCTION, LOSS OF WIPER PARK FUNCTION, COMPLETE LOSS OF WIPER FUNCTION, OR IGNITION OF THE PLASTIC COVER MATERIAL. SWITCH MALFUNCTION IS MOST LIKELY TO OCCUR WHEN THE INTERMITTENT SETTING OF THE WIPERS IS BEING USED, OR WHEN SNOW OR ICE OBSTRUCTS THE BLADES FROM RETURNING TO THE PARKED POSITION AT THE BOTTOM OF THE WINDSHIELD. THESE VEHICLES WERE BUILT AT THE FOLLOWING ASSEMBLY PLANTS: ATLANTA PLANT FROM 2/11/00 THROUGH 7/31/00; CHICAGO PLANT FROM 2/14/00 THROUGH 8/4/00; KANSAS CITY PLANT FROM 2/26/00 TO 9/4/00; KENTUCKY TRUCK PLANT FROM 2/18/00 TO 8/31/00; MICHIGAN TRUCK PLANT FROM 2/23/00 THROUGH 8/3/00; NORFOLK PLANT FROM 2/21/00 THROUGH 7/27/00; WAYNE STAMPING AND ASSEMBLY PLANT FROM 2/25/00 THROUGH 8/15/00; AND WIXOM PLANT FROM 2/15/00 THROUGH 8/8/00.
THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH THE SAFETY ACT. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. VEHICLE DESCRIPTION: 1998 FORD CONTOUR/MERCURY MYSTIQUE PASSENGER VEHICLES BUILT AT THE KANSAS CITY ASSEMBLY PLANT. THE FRONT COIL SPRINGS COULD POTENTIALLY FRACTURE DUE TO CORROSION.
VEHICLE DESCRIPTION: PASSENGER VEHICLES BUILT AT THE KANSAS CITY ASSEMBLY PLANT AND ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN, AND THE DISTRICT OF COLUMBIA. THE FRONT COIL SPRINGS MAY FRACTURE AS A RESULT OF CORROSION IN HIGH CORROSION ENVIRONMENTS. DEPENDING ON THE LOCATION OF THE FRACTURE, A BROKEN SPRING COULD MOVE PAST THE SPRING SEAT AND CONTACT A FRONT TIRE.
VEHICLE DESCRIPTION: PASSENGER AND SPORT UTILITY VEHICLES, PICKUP TRUCKS, AND MINIVANS. EQUIPPED WITH SEAT BELTS SUPPLIED BY TRW. IT IS POSSIBLE THAT THE DRIVER'S AND/OR FRONT PASSENGER'S OUTBOARD SEAT BELT BUCKLE MAY NOT FULLY LATCH. FORD CROWN VICTORIA BUILT AT ST. THOMAS ASSEMBLY PLANT FROM 4/17/00 - 5/29/01 MERCURY GRAND MARQUIS BUILT AT ST. THOMAS ASSEMBLY PLANT FROM 4/17/00 - 5/29/01. LINCOLN TOWN CARS BUILT AT WIXOM ASSEMBLY PLANT FROM 3/27/00 - 5/30/01. LINCOLN NAVIGATORS BUILT AT MICHIGAN TRUCK PLANT FROM 4/11/00 - 5/31/01. FORD WINDSTARS BUILT AT OAKVILLE ASSEMBLY PLANT FROM 3/23/00 - 5/30/01. FORD RANGERS BUILT AT TWIN CITIES PLANT FROM 3/28/00 - 5/30/01, AND ALSO AT THE EDISON PLANT FROM 3/13/00 - 5/25/01. FORD F-150 TRUCK BUILT AT NORFOLK PLANT FROM 4/18/00 - 5/25/00; AT ONTARIO PLANT FROM 5/10/00 - 5/28/01; AT KANSAS CITY PLANT FROM 9/11/99 - 5/25/01; AND AT CUAUTITLAN PLANT FROM 5/16/00 - 6/9/01. FORD SUPER DUTY F-250, F-350, F-450, AND F-550 TRUCKS BUILT AT KENTUCKY PLANT FROM 4/17/00 - 5/27/01; AND AT CUAUTITLAN PLANT FROM 5/16/00 - 6/19/01. FORD EXCURSIONS BUILT AT KENTUCKY PLANT FROM 4/17/00 - 10/2/00. FORD EXPEDITIONS BUILT AT MICHIGAN TRUCK PLANT FROM 4/11/00 - 5/31/01.
THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH THE SAFETY ACT. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. VEHICLE DESCRIPTION: 1995-1997 FORD CONTOUR AND MERCURY MYSTIQUE VEHICLES. THE HEATER BLOWER RESISTOR COULD OVERHEAT CAUSING THE ATTACHED ELECTRICAL CONNECTOR TO MELT.
THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH THE SAFETY ACT. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. VEHICLE DESCRIPTION: 1995-1997 FORD CONTOUR AND MERCURY MYSTIQUE VEHICLES. THE HEATER BLOWER RESISTOR COULD OVERHEAT CAUSING THE ATTACHED ELECTRICAL CONNECTOR TO MELT.
THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH THE SAFETY ACT. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. VEHICLE DESCRIPTION: 1995-1997 FORD CONTOUR AND MERCURY MYSTIQUE VEHICLES. THE HEATER BLOWER RESISTOR COULD OVERHEAT CAUSING THE ATTACHED ELECTRICAL CONNECTOR TO MELT.
ON CERTAIN MY 1996-1998 PASSENGER VEHICLES BUILT AT THE KANSAS CITY, CUAUTITLAN ASSEMBLY PLANTS OR ON MY 1999 PASSENGER VEHCLES BUILT AT THE AUTOMOTIVE ALLIANCE INTERNATIONAL ASSEMBLY PLANTS, THE ROUGH SURFACE OF THE HEATER BLOWER RESISTOR'S STAINLESS STEEL BLADES CAN DAMAGE THE COPPER SURFACE OF THE WIRING HARNESS CONNECTOR. THE DAMAGE COULD, OVER TIME, CAUSE INCREASED RESISTANCE IN THE CONNECTOR AND, DUE TO SUBSEQUENT TERMINAL RELAXATION, RESULT IN AN OPEN CIRCUIT CONDITION.
ON CERTAIN MY 1996-1998 PASSENGER VEHICLES BUILT AT THE KANSAS CITY, CUAUTITLAN ASSEMBLY PLANTS OR ON MY 1999 PASSENGER VEHCLES BUILT AT THE AUTOMOTIVE ALLIANCE INTERNATIONAL ASSEMBLY PLANTS, THE ROUGH SURFACE OF THE HEATER BLOWER RESISTOR'S STAINLESS STEEL BLADES CAN DAMAGE THE COPPER SURFACE OF THE WIRING HARNESS CONNECTOR. THE DAMAGE COULD, OVER TIME, CAUSE INCREASED RESISTANCE IN THE CONNECTOR AND, DUE TO SUBSEQUENT TERMINAL RELAXATION, RESULT IN AN OPEN CIRCUIT CONDITION.
ON CERTAIN MY 1996-1998 PASSENGER VEHICLES BUILT AT THE KANSAS CITY, CUAUTITLAN ASSEMBLY PLANTS OR ON MY 1999 PASSENGER VEHCLES BUILT AT THE AUTOMOTIVE ALLIANCE INTERNATIONAL ASSEMBLY PLANTS, THE ROUGH SURFACE OF THE HEATER BLOWER RESISTOR'S STAINLESS STEEL BLADES CAN DAMAGE THE COPPER SURFACE OF THE WIRING HARNESS CONNECTOR. THE DAMAGE COULD, OVER TIME, CAUSE INCREASED RESISTANCE IN THE CONNECTOR AND, DUE TO SUBSEQUENT TERMINAL RELAXATION, RESULT IN AN OPEN CIRCUIT CONDITION.
ON CERTAIN MY 1996-1998 PASSENGER VEHICLES BUILT AT THE KANSAS CITY, CUAUTITLAN ASSEMBLY PLANTS OR ON MY 1999 PASSENGER VEHCLES BUILT AT THE AUTOMOTIVE ALLIANCE INTERNATIONAL ASSEMBLY PLANTS, THE ROUGH SURFACE OF THE HEATER BLOWER RESISTOR'S STAINLESS STEEL BLADES CAN DAMAGE THE COPPER SURFACE OF THE WIRING HARNESS CONNECTOR. THE DAMAGE COULD, OVER TIME, CAUSE INCREASED RESISTANCE IN THE CONNECTOR AND, DUE TO SUBSEQUENT TERMINAL RELAXATION, RESULT IN AN OPEN CIRCUIT CONDITION.
VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. THE RIGHT SIDE TIRES MAY HAVE HORIZONTAL CUTS ON THE EDGE OF THE TREAD THAT COULD HAVE OCCURRED DURING VEHICLE ASSEMBLY.
VEHICLE DESCRIPTION: PASSENGER CARS. THE SEAT BELT BUCKLE TONGUE MAY NOT FULLY EJECT FROM THE BUCKLE ASSEMBLY WHEN THE RELEASE BUTTON IS PUSHED SLOWLY. THIS CONDITION COULD ALSO RESULT IN A PARTIAL LATCH OF THE TONGUE IN THE BUCKLE.
THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH THE SAFETY ACT. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. VEHICLE DESCRIPTION: 2002 FORD EXPLORER AND MERCURY MONTAINEER SPORT UTILITY VEHICLES. THE BRACKETS CONNECTING THE LEFT CYLINDERS TO EACH SIDE OF THE LIFTGATE GLASS COULD ROTATE OUT OF POSITION IF EITHER THE URETHANE BOND OR TORQUE ARE NOT SUFFICIENT.
VEHICLE DESCRIPTION: PASSENGER AND SPORT UTILITY VEHICLES. DUE TO THE USE OF INCORRECT MATERIAL BY A SUPPLIER, THE HEADLAMP SWITCH KNOB CAN FRACTURE AND SEPARATE FROM THE HEADLAMP SWITCH.
VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH ADJUSTABLE PEDALS. IF THE GREASE FROM THE ADJUSTABLE PEDAL ASSEMBLY ENTERS THE STOP LAMP SWITCH, IT CAN CONTAMINATE THE CONTACTS LEADING TO CARBON BUILD UP, AND POTENTIALLY, A SHORT CIRCUIT.
VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH ADJUSTABLE PEDALS. IF THE GREASE FROM THE ADJUSTABLE PEDAL ASSEMBLY ENTERS THE STOP LAMP SWITCH, IT CAN CONTAMINATE THE CONTACTS LEADING TO CARBON BUILD UP, AND POTENTIALLY, A SHORT CIRCUIT.
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE BRAKE LAMP SWITCH TERMINALS COULD OVERHEAT.
VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH 2.5L V6 ENGINES. THE BATTERY CABLE WAS MISROUTED AND ITS ATTACHMENT TO THE ALTERNATOR CABLE WAS UNDER-TORQUED. IF MISROUTED, THE CABLE COULD CONTACT THE POWER STEERING LINE AND THE INSULATION COULD WEAR, RESULTING IN AN ELECTRICAL SHORT.
VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH 2.5L V6 ENGINES. THE BATTERY CABLE WAS MISROUTED AND ITS ATTACHMENT TO THE ALTERNATOR CABLE WAS UNDER-TORQUED. IF MISROUTED, THE CABLE COULD CONTACT THE POWER STEERING LINE AND THE INSULATION COULD WEAR, RESULTING IN AN ELECTRICAL SHORT.
VEHICLE DESCRIPTION: MINIVANS. THE FUEL TANK VENT HOSE ALLOWS AIR TO VENT FROM THE FUEL TANK DURING REFUELING. CRACKS HAVE DEVELOPED IN THE VENT HOSE. IF (1) THE FUEL TANK IS OVERFILLED, NOT ALLOWING EXCESS FUEL IN THE VENT HOSE TO FLOW BACK INTO THE TANK, (2) THE VEHICLE IS DRIVEN ONLY A SHORT DISTANCE AFTER REFUELING AND, (3) THERE IS SUBSEQUENTLY SIGNIFICANT HEATING OF THE FUEL TANK, THE FUEL IN THE TANK CAN EXPAND INTO THE VENT HOSE AND LEAK FUEL.
