Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. PAINT WAS APPLIED UNEVENLY ON THE REAR AXLES, RESULTING IN INSUFFICIENT PAINT HARDNESS. SHOULD THIS OCCUR ON THE SURFACE THAT CONTACTS THE REAR AXLE LOWER LINK BRACKET BOLT HEAD AND/OR NUT, THE NUT MAY LOOSEN.
VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. PAINT WAS APPLIED UNEVENLY ON THE REAR AXLES, RESULTING IN INSUFFICIENT PAINT HARDNESS. SHOULD THIS OCCUR ON THE SURFACE THAT CONTACTS THE REAR AXLE LOWER LINK BRACKET BOLT HEAD AND/OR NUT, THE NUT MAY LOOSEN.
VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. PAINT WAS APPLIED UNEVENLY ON THE REAR AXLES, RESULTING IN INSUFFICIENT PAINT HARDNESS. SHOULD THIS OCCUR ON THE SURFACE THAT CONTACTS THE REAR AXLE LOWER LINK BRACKET BOLT HEAD AND/OR NUT, THE NUT MAY LOOSEN.
VEHICLE DESCRIPTION: PASSENGER VEHICLES. CERTAIN VEHICLES WERE MANUFACTURED WITH BALL JOINTS THAT CAN PREMATURELY WEAR OUT AND, IN THE WORSE CASE, THE BALL JOINT WOULD SEPARATE CAUSING THE FRONT SUSPENSION TO COLLAPSE.
VEHICLE DESCRIPTION: PASSENGER VEHICLES. CERTAIN VEHICLES WERE MANUFACTURED WITH BALL JOINTS THAT CAN PREMATURELY WEAR OUT AND, IN THE WORSE CASE, THE BALL JOINT WOULD SEPARATE CAUSING THE FRONT SUSPENSION TO COLLAPSE.
VEHICLE DESCRIPTION: PASSENGER VEHICLES. CERTAIN VEHICLES WERE MANUFACTURED WITH BALL JOINTS THAT CAN PREMATURELY WEAR OUT AND, IN THE WORSE CASE, THE BALL JOINT WOULD SEPARATE CAUSING THE FRONT SUSPENSION TO COLLAPSE.
VEHICLE DESCRIPTION: PASSENGER VEHICLES. CERTAIN VEHICLES WERE MANUFACTURED WITH BALL JOINTS THAT CAN PREMATURELY WEAR OUT AND, IN THE WORSE CASE, THE BALL JOINT WOULD SEPARATE CAUSING THE FRONT SUSPENSION TO COLLAPSE.
VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH A SUNROOF SUNSHADE. THE PRIMER APPLIED TO PREPARE THE SURFACE PRIOR TO BONDING THE SUNSHADE HOLDERS TO THE SUNROOF WEAKENED THE BONDING STRENGTH OF THE ADHESIVE, RESULTING IN AN UNSATISFACTORY BOND OF THE HOLDER TO THE SUNROOF.
VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. THE TRANSFER GEARBOX FLANGE NUTS WERE NOT PROPERLY INSTALLED, CAUSING THE NUTS TO LOOSEN.
VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. A GROUND CONNECTION TERMINAL WAS NOT PROPERLY CRIMPED IN THE SUPPLIER'S ENGINE WIRING HARNESS MANUFACTURING LINE. THIS IMPROPER CRIMPING PROCESS CAN LEAVE AN IMPRESSION ON THE TERMINAL THAT WILL EVENTUALLY CAUSE A STRESS FRACTURE. S
VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. A GROUND CONNECTION TERMINAL WAS NOT PROPERLY CRIMPED IN THE SUPPLIER'S ENGINE WIRING HARNESS MANUFACTURING LINE. THIS IMPROPER CRIMPING PROCESS CAN LEAVE AN IMPRESSION ON THE TERMINAL THAT WILL EVENTUALLY CAUSE A STRESS FRACTURE. S
VEHICLE DESCRIPTION: TRUCK CHASSIS. THE INTERMEDIATE STEERING SHAFT-TO-STEERING BOLT WAS NOT TIGHTENED PROPERLY DURING ASSEMBLY. THIS CAN CAUSE STEERING NOISE, LOOSE STEERING, AND AN UNCENTERED STEERING WHEEL.
VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES, 2 AND 4-WHEEL DRIVE. SOLDER JOINTS NEAR THE WIRING HARNESS CONNECTOR CAN CRACK CAUSING THE WINDSHIELD WIPERS TO WORK INTERMITTENTLY.
VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. THE STRENGTH OF THE REAR SEAT BELT SHOULDER ANCHORAGE IS NOT TO DESIGN SPECIFICATIONS AND DOES NOT FULLY COMPLY WITH REQUIREMENTS OF FMVSS NO. 210, SEAT BELT ASSEMBLY ANCHORAGES.
VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS AND MULTI-PURPOSE VEHICLES. AN ENGINE ELECTRICAL WIRING-HARNESS CLIP CAN MELT AND DRIP ONTO THE EXHAUST MANIFOLD.
VEHICLE DESCRIPTION: MULTI-PURPOSE PASSENGER VEHICLES EQUIPPED WITH A DRIVER'S SIDE OPTIONAL EQUIPMENT RUBBER FLOOR MAT. REPEATED MOVEMENT OF THE DRIVER'S FEET AND ACTUATION OF THE ACCELERATOR PEDAL CAN RESULT IN A SHIFTING OF THE MAT'S POSITION. THIS SHIFTING CAN CAUSE AN INTERFERENCE WITH THE ACCELERATOR PEDAL.
VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER PICKUP TRUCKS EQUIPPED WITH 4.3L ENGINES. THE FRONT BRAKE LINE CAN CONTACT THE LEFT-HAND SIDE OF THE ENGINE OIL PAN CAUSING THE BRAKE LINE TO WEAR TO THE POINT OF BRAKE FLUID LOSS DURING BRAKE APPLICATION.
VEHICLE DESCRIPTION: EXTENDED CAB PICKUP TRUCKS EQUIPPED WITH 60/40 FRONT BENCH SEATS AND EXTENDED CAB PICKUP TRUCKS AND 2-DOOR UTILITY VEHICLES EQUIPPED WITH MANUAL LOCKING RECLINER BUCKET SEATS. THE OUTBOARD SAFETY BELT WEBBING ON THE DRIVER'S AND/OR PASSENGER'S SEAT CAN SEPARATE DURING A FRONTAL IMPACT.
THE LEFT FRONT BRAKE LINES WERE INSTALLED IMPROPERLY AT THE ASSEMBLY LINE RESULTING IN INSUFFICIENT CLEARANCE BETWEEN THE BRAKE LINE AND AN UPPER CONTROL ARM OF THE SUSPENSION.
THE LEFT FRONT BRAKE LINES WERE INSTALLED IMPROPERLY AT THE ASSEMBLY LINE RESULTING IN INSUFFICIENT CLEARANCE BETWEEN THE BRAKE LINE AND AN UPPER CONTROL ARM OF THE SUSPENSION.
THE FRONT AXLE BRAKE HOSES WERE DAMAGED DURING TRANSPORTATION OF THE FRONT AXLE ASSEMBLY WITH THE BRAKE HOSES ATTACHED.
THESE VEHICLES WERE MANUFACTURED WITHOUT A LOCK WASHER AND/OR SCREWS IN THE FRONT HUB.
AN INTEGRATED CIRCUIT WITHIN THE VOLTAGE REGULATOR CAN CONTAIN MANUFACTURING ERRORS.
AN INTEGRATED CIRCUIT WITHIN THE VOLTAGE REGULATOR CAN CONTAIN MANUFACTURING ERRORS.
AN INTEGRATED CIRCUIT WITHIN THE VOLTAGE REGULATOR CAN CONTAIN MANUFACTURING ERRORS.
THE TOP COAT PAINT SEVERELY PEELS DUE TO OVERBAKING OF THE POWDER PRIMER PRIOR TO THE TOP COAT APPLICATION. SINCE THE WINDSHIELD PRIMER AND ADHESIVE ADHERE TO THE TOP COAT PAINT ONTHE WINDSHIELD OPENING FLANGE, THE WINDSHIELD DOES NOT COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 212, WINDSHIELD MOUNTING.
CERTAIN VEHICLES WERE MANUFACTURED WITH AN INCORRECT REAR CENTER SEAT BELT ASSEMBLY BUCKLE. THE MISBUILD INVOLVED FITTING A BUCKLE FOR ANOTHER MARKET WITH THE CORRECT U.S. SPECIFICATION SEAT BELT.
THE LATCH PLATE USED IN THE SEAT BELT BUCKLE WAS NOT MANUFACTURED ACCORDING TO DESIGN DIMENSIONS. IF THE SEAT BELT TONGUE IS INSERTED SLOWLY AT AN ANGLE INTO THE BUCKLE, THERE IS A POSSIBILITY OF PARTIAL ENGAGEMENT.
THE LATCH PLATE USED IN THE SEAT BELT BUCKLE WAS NOT MANUFACTURED ACCORDING TO DESIGN DIMENSIONS. IF THE SEAT BELT TONGUE IS INSERTED SLOWLY AT AN ANGLE INTO THE BUCKLE, THERE IS A POSSIBILITY OF PARTIAL ENGAGEMENT.
THE LATCH PLATE USED IN THE SEAT BELT BUCKLE WAS NOT MANUFACTURED ACCORDING TO DESIGN DIMENSIONS. IF THE SEAT BELT TONGUE IS INSERTED SLOWLY AT AN ANGLE INTO THE BUCKLE, THERE IS A POSSIBILITY OF PARTIAL ENGAGEMENT.
