Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
A CHILD COULD OPEN THE REAR SIDE COMPARTMENT DOOR AND ENTER THIS COMPARTMENT. THE CHILD COULD BECOME ENTRAPPED IF THE DOOR WERE TO CLOSE, AS IT CANNOT BE UNLATCHED FROM THE INSIDE.
A CHILD COULD OPEN THE REAR SIDE COMPARTMENT DOOR AND ENTER THIS COMPARTMENT. THE CHILD COULD BECOME ENTRAPPED IF THE DOOR WERE TO CLOSE, AS IT CANNOT BE UNLATCHED FROM THE INSIDE.
A CHILD COULD OPEN THE REAR SIDE COMPARTMENT DOOR AND ENTER THIS COMPARTMENT. THE CHILD COULD BECOME ENTRAPPED IF THE DOOR WERE TO CLOSE, AS IT CANNOT BE UNLATCHED FROM THE INSIDE.
THE CARBURETOR FUEL FEED HOSE MAY NOT HAVE BEEN PROPERLY POSITIONED DURING ASSEMBLY. AS A RESULT THE HOSE COULD COME IN CONTACT WITH OR BE TOO CLOSE TO THE ENGINE EMISSION EXHAUST SYSTEM GAS RECIRCULATION VALVE. THIS CAN CAUSE THE HOSE TO RUPTURE.
ON THE INVOLVED VEHICLES THE BRAKE STOPLIGHT AND CRUISE CONTROL SWITCH WHICH IS OPERATED BY THE BRAKE PEDAL MAY HAVE BEEN ASSEMBLED WITH AN INCORRECT LUBRICANT ON THE ACTUATING PLUNGER. THIS CAN CAUSE THE REAR BRAKE STOPLIGHTS TO BECOME INOPERATIVE AND THE CRUISE CONTROL, IF ACTIVATED, TO STAY ELECTRICALLY ENGAGED.
ON THE INVOLVED VEHICLES THE BRAKE STOPLIGHT AND CRUISE CONTROL SWITCH WHICH IS OPERATED BY THE BRAKE PEDAL MAY HAVE BEEN ASSEMBLED WITH AN INCORRECT LUBRICANT ON THE ACTUATING PLUNGER. THIS CAN CAUSE THE REAR BRAKE STOPLIGHTS TO BECOME INOPERATIVE AND THE CRUISE CONTROL, IF ACTIVATED, TO STAY ELECTRICALLY ENGAGED.
ON THE INVOLVED VEHICLES THE BRAKE STOPLIGHT AND CRUISE CONTROL SWITCH WHICH IS OPERATED BY THE BRAKE PEDAL MAY HAVE BEEN ASSEMBLED WITH AN INCORRECT LUBRICANT ON THE ACTUATING PLUNGER. THIS CAN CAUSE THE REAR BRAKE STOPLIGHTS TO BECOME INOPERATIVE AND THE CRUISE CONTROL, IF ACTIVATED, TO STAY ELECTRICALLY ENGAGED.
ON THE INVOLVED VEHICLES THE BRAKE STOPLIGHT AND CRUISE CONTROL SWITCH WHICH IS OPERATED BY THE BRAKE PEDAL MAY HAVE BEEN ASSEMBLED WITH AN INCORRECT LUBRICANT ON THE ACTUATING PLUNGER. THIS CAN CAUSE THE REAR BRAKE STOPLIGHTS TO BECOME INOPERATIVE AND THE CRUISE CONTROL, IF ACTIVATED, TO STAY ELECTRICALLY ENGAGED.
ON THE INVOLVED VEHICLES THE BRAKE STOPLIGHT AND CRUISE CONTROL SWITCH WHICH IS OPERATED BY THE BRAKE PEDAL MAY HAVE BEEN ASSEMBLED WITH AN INCORRECT LUBRICANT ON THE ACTUATING PLUNGER. THIS CAN CAUSE THE REAR BRAKE STOPLIGHTS TO BECOME INOPERATIVE AND THE CRUISE CONTROL, IF ACTIVATED, TO STAY ELECTRICALLY ENGAGED.
ON THE INVOLVED VEHICLES THE BRAKE STOPLIGHT AND CRUISE CONTROL SWITCH WHICH IS OPERATED BY THE BRAKE PEDAL MAY HAVE BEEN ASSEMBLED WITH AN INCORRECT LUBRICANT ON THE ACTUATING PLUNGER. THIS CAN CAUSE THE REAR BRAKE STOPLIGHTS TO BECOME INOPERATIVE AND THE CRUISE CONTROL, IF ACTIVATED, TO STAY ELECTRICALLY ENGAGED.
ON THE INVOLVED VEHICLES THE BRAKE STOPLIGHT AND CRUISE CONTROL SWITCH WHICH IS OPERATED BY THE BRAKE PEDAL MAY HAVE BEEN ASSEMBLED WITH AN INCORRECT LUBRICANT ON THE ACTUATING PLUNGER. THIS CAN CAUSE THE REAR BRAKE STOPLIGHTS TO BECOME INOPERATIVE AND THE CRUISE CONTROL, IF ACTIVATED, TO STAY ELECTRICALLY ENGAGED.
ON THE INVOLVED VEHICLES THE BRAKE STOPLIGHT AND CRUISE CONTROL SWITCH WHICH IS OPERATED BY THE BRAKE PEDAL MAY HAVE BEEN ASSEMBLED WITH AN INCORRECT LUBRICANT ON THE ACTUATING PLUNGER. THIS CAN CAUSE THE REAR BRAKE STOPLIGHTS TO BECOME INOPERATIVE AND THE CRUISE CONTROL, IF ACTIVATED, TO STAY ELECTRICALLY ENGAGED.
ON THE INVOLVED VEHICLES THE BRAKE STOPLIGHT AND CRUISE CONTROL SWITCH WHICH IS OPERATED BY THE BRAKE PEDAL MAY HAVE BEEN ASSEMBLED WITH AN INCORRECT LUBRICANT ON THE ACTUATING PLUNGER. THIS CAN CAUSE THE REAR BRAKE STOPLIGHTS TO BECOME INOPERATIVE AND THE CRUISE CONTROL, IF ACTIVATED, TO STAY ELECTRICALLY ENGAGED.
ON THE INVOLVED VEHICLES THE BRAKE STOPLIGHT AND CRUISE CONTROL SWITCH WHICH IS OPERATED BY THE BRAKE PEDAL MAY HAVE BEEN ASSEMBLED WITH AN INCORRECT LUBRICANT ON THE ACTUATING PLUNGER. THIS CAN CAUSE THE REAR BRAKE STOPLIGHTS TO BECOME INOPERATIVE AND THE CRUISE CONTROL, IF ACTIVATED, TO STAY ELECTRICALLY ENGAGED.
THE ENGINE OIL PRESSURE SWITCH MAY CAUSE A RANDOM INTERNAL ELECTRICAL SHORT WHICH COULD RESULT IN THE ENGINE STARTING BY ITSELF WHEN THE IGNITION SWITCH IS TURNED TO THE ON POSITION.
THE FRONT SUSPENSION COIL SPRING MAY HAVE A LARGER THAN DESIRED INSIDE DIAMETER OF THE LOWER COIL WHERE IT RESTS ON THE SPRING SEAT. THIS COULD ALLOW THE SPRING TO BE FORCED OVER THE LOWER SPRING SEAT DUE TO SUSPENSION FORCES.
THERE IS A POTENTIAL FOR INTERFERENCE BETWEEN THE CLUTCH CONTROL CABLE AND BRAKE PIPE IN THE MASTER CYLINDER. THIS CAN RESULT IN RUBBING CONTACT WHEN THE CLUTCH PEDAL IS OPERATED. ALSO, THE BRAKE PIPE CLEARANCE TO THE TRANSMISSION CASE MAY BE INADEQUATE. IF THIS CONDITION EXISTS, IT COULD EVENTUALLY RESULT IN A FAILURE IN THE BRAKE PIPE, CAUSING LOSS OF BRAKE FLUID AND PARTIAL LOSS OF BRAKING ACTION.
FUEL HOSES MAY BE INCORRECTLY POSITIONED AND CONTACT THE RIGHT FRONT DRIVE AXLE BOOT DURING VEHICLE OPERATION. AFTER A PERIOD OF TIME, THE ROTATING BOOT COULD WEAR A HOLE IN THE FUEL HOSE, RESULTING IN FULE LEAKAGE.
THE LONGITUDINAL BODY BARS AT THE REAR CONTROL ARM LOCATION MAY NOT HAVE BEEN ADEQUATELY WELDED INTO THE STRUCTURE. SOME OF THESE BARS MAY HAVE BEEN PULLED DOWN FROM THE BODY DURING SHIPMENT WITH RESULTING DAMAGE TO THE BRAKE OR FUEL LINES. SEPARATION OF THE CONTROL ARM ATTACHMENT MAY ALSO RESULT.
OPERATION OF THE VEHICLE IN A MANNER WHICH PRODUCES HARD BOTTOMING OUT OF THE FRONT SUSPENSION MAY CAUSE DEFORMATION OF THE LEFT ENGINE MOUNT SUPPORT STRUCTURE AND ALLOW THE ENGINE MOUNT BRACKET TO CONTACT THE STEERING PITMAN ARM OR STEERING LINKAGE.
OPERATION OF THE VEHICLE IN A MANNER WHICH PRODUCES HARD BOTTOMING OUT OF THE FRONT SUSPENSION MAY CAUSE DEFORMATION OF THE LEFT ENGINE MOUNT SUPPORT STRUCTURE AND ALLOW THE ENGINE MOUNT BRACKET TO CONTACT THE STEERING PITMAN ARM OR STEERING LINKAGE.
VEHICLES DO NOT COMPLY TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 207, ANCHORAGE OF SEATS. THE LOCK BAR IN THE FRONT SEAT ADJUSTER ASSEMBLIES MAY NOT ENGAGE PROPERLY AND THE ABILITY OF THE SEAT ADJUSTER TO MAINTAIN THE SEAT IN A LATCHED POSITION DURING AN ACCIDENT MAY BE REDUCED.
THE FRONT HOSES ON THE INVOLVED VEHICLES MAY HAVE IMPROPERLY ORIENTED HOSE FITTINGS, RESULTING IN A RUBBING CONTACT BETWEEN THE RIGHT BRAKE HOSE AND THE UPPER CONTROL ARM OF THE FRONT SUSPENSION OR IN A TWISTED LEFT HOSE RESULTING IN A FAULTY ATTACHMENT AT THE FRAME FITTING. SHOULD EITHER OF THESE CONDITIONS EXIST, THEY COULD EVENTUALLY RESULT IN BRAKE HOSE FAILURE CAUSING LOSS OF BRAKE FLUID AND CONSEQUENT LOSS OF THE FRONT BRAKING ACTION.
THE FRONT HOSES ON THE INVOLVED VEHICLES MAY HAVE IMPROPERLY ORIENTED HOSE FITTINGS, RESULTING IN A RUBBING CONTACT BETWEEN THE RIGHT BRAKE HOSE AND THE UPPER CONTROL ARM OF THE FRONT SUSPENSION OR IN A TWISTED LEFT HOSE RESULTING IN A FAULTY ATTACHMENT AT THE FRAME FITTING. SHOULD EITHER OF THESE CONDITIONS EXIST, THEY COULD EVENTUALLY RESULT IN BRAKE HOSE FAILURE CAUSING LOSS OF BRAKE FLUID AND CONSEQUENT LOSS OF THE FRONT BRAKING ACTION.
THE FUEL SYSTEM MAY NOT COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 301, FUEL SYSTEM INTEGRITY. IN THE EVENT OF A VEHICLE COLLISION FROM THE REAR, EXCESSIVE FUEL SPILLAGE MAY OCCUR.
THE FUEL SYSTEM MAY NOT COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 301, FUEL SYSTEM INTEGRITY. IN THE EVENT OF A VEHICLE COLLISION FROM THE REAR, EXCESSIVE FUEL SPILLAGE MAY OCCUR.
THE STEERING WHEEL MAY HAVE BEEN ASSEMBLED WITH STEERING WHEEL RETENTION FASTENERS THAT WERE NOT SUFFICIENTLY TIGHTENED. THE STEERING WHEEL COULD BECOME LOOSE AND SEPARATE FROM THE STEERING WHEEL HUB.
THE INVOLVED ENGINE FAN ASSEMBLIES MAY BE OF INADEQUATE DURABILITY. CONSEQUENTLY, THE FAN SPIDER MAY WEAR OVER A PEROID OF TIME AND BREAK AT THE HUB WITHOUT WARNING, WHILE THE ENGINE IS RUNNING.
THE INVOLVED ENGINE FAN ASSEMBLIES MAY BE OF INADEQUATE DURABILITY. CONSEQUENTLY, THE FAN SPIDER MAY WEAR OVER A PEROID OF TIME AND BREAK AT THE HUB WITHOUT WARNING, WHILE THE ENGINE IS RUNNING.
UNDER CERTAIN DRIVING CONDITIONS, INCLUDING EXTENDED SEVERE BRAKING, THE WHEEL BEARING AREA MAY ENCOUNTER TEMPERATURES THAT CAN CAUSE THE GREASE TO MIGRATE OUT OF THE BEARING AREA. THIS WILL REDUCE THE AMOUNT OF LUBRICATION AVAILABLE TO THE BEARINGS AND RESULT IN FRONT WHEEL BEARING FAILURE AND SPINDLE DAMAGE.
