Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
TRUCKS WERE ASSEMBLED WITH THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TIGHTENED BELOW THE SPECIFIED TORQUE. LOW TORQUE ON THIS NUT MAY ALLOW THE ATTACHMENT BOLT TO LOOSED AND SUBSEQUENTLY FATIGUE AND BREAK. THE BOLT BREAKAGE CAN CAUSE THE LEFT HAND CONTROL ARM TO SEPARATE FROM THE FRAME.
TRUCKS WERE ASSEMBLED WITH THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TIGHTENED BELOW THE SPECIFIED TORQUE. LOW TORQUE ON THIS NUT MAY ALLOW THE ATTACHMENT BOLT TO LOOSED AND SUBSEQUENTLY FATIGUE AND BREAK. THE BOLT BREAKAGE CAN CAUSE THE LEFT HAND CONTROL ARM TO SEPARATE FROM THE FRAME.
TRUCKS WERE ASSEMBLED WITH THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TIGHTENED BELOW THE SPECIFIED TORQUE. LOW TORQUE ON THIS NUT MAY ALLOW THE ATTACHMENT BOLT TO LOOSED AND SUBSEQUENTLY FATIGUE AND BREAK. THE BOLT BREAKAGE CAN CAUSE THE LEFT HAND CONTROL ARM TO SEPARATE FROM THE FRAME.
TRUCKS WERE ASSEMBLED WITH THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TIGHTENED BELOW THE SPECIFIED TORQUE. LOW TORQUE ON THIS NUT MAY ALLOW THE ATTACHMENT BOLT TO LOOSED AND SUBSEQUENTLY FATIGUE AND BREAK. THE BOLT BREAKAGE CAN CAUSE THE LEFT HAND CONTROL ARM TO SEPARATE FROM THE FRAME.
TRUCKS WERE ASSEMBLED WITH THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TIGHTENED BELOW THE SPECIFIED TORQUE. LOW TORQUE ON THIS NUT MAY ALLOW THE ATTACHMENT BOLT TO LOOSED AND SUBSEQUENTLY FATIGUE AND BREAK. THE BOLT BREAKAGE CAN CAUSE THE LEFT HAND CONTROL ARM TO SEPARATE FROM THE FRAME.
ONE OF THE THREE SPECIFIED TRAILER HITCH FASTENERS PER SIDE IS MISSING WHICH CAN CAUSE THE EXISTING FASTENERS TO LOOSEN AND FAIL.
ONE OF THE THREE SPECIFIED TRAILER HITCH FASTENERS PER SIDE IS MISSING WHICH CAN CAUSE THE EXISTING FASTENERS TO LOOSEN AND FAIL.
THESE VEHICLES WERE EQUIPPED WITH INCORRECT SPARE WHEELS. THE USE OF AN INCORRECT SPARE WHEEL IN A MOUNTED POSITION CAN, UNDER CERTAIN LOAD CONDITIONS, EVENTUALLY CAUSE THE WHEEL TO CRACK AND POSSIBLY SEPARATE FROM THE VEHICLE.
THE ENGINE OIL COOLER INLET HOSE MAY HAVE BEEN INSTALLED TOO CLOSE TO THE STEERING GEAR CAUSING CHAFING. THE CHAFING CAN EVENTUALLY WEAR THROUGH THE HOSE'S PROTECTIVE SLEEVE RESULTING IN ENGINE OIL LEAKING ONTO THE ENGINE.
THE FRONT FUEL TANK BRACKET ATTACHMENT NUTS WERE TORQUED BELOW THE SPECIFICATION. THESE LOOSE NUTS CAN, IN TIME, COME OFF THE BRACKET STUDS ALLOWING THE FRONT OF THE TANK TO SAG BELOW THE NORMAL VEHICLE SILHOUETTE.
THE FRONT FUEL TANK BRACKET ATTACHMENT NUTS WERE TORQUED BELOW THE SPECIFICATION. THESE LOOSE NUTS CAN, IN TIME, COME OFF THE BRACKET STUDS ALLOWING THE FRONT OF THE TANK TO SAG BELOW THE NORMAL VEHICLE SILHOUETTE.
THE FUEL TANK FILLER PIPES WERE NOT MANUFACTURED TO SPECIFICATION WHICH CAUSED LOSS OF FUEL BETWEEN THE FUEL TANK FILLER PIPE AND THE VENT TUBE DURING A TEST. THE LOSS OF FUEL WAS IN EXCESS OF THE AMOUNT PERMITTED BY FMVSS NO. 301, FUEL SYSTEM INTEGRITY.
THE THIRD ROW SAFETY BELT RETRACTORS MAY BE INSTALLED INCORRECTLY AND MAY LOCK-UP WHEN THE VEHICLE IS ON SLOPES OF LESS THAN 15 DEGREES, WHICH DOES NOT COMPLY WITH FMVSS NO. 209, SEAT BELT ASSEMBLIES.
THE INTERMEDIATE STEERING SHAFT WAS ASSEMBLED WITH LOOSE OR MISSING UPPER AND LOWER PINCH BOLTS WHICH MAY CAUSE SEPARATION OF THE SHAFT.
THE INTERMEDIATE STEERING SHAFT WAS ASSEMBLED WITH LOOSE OR MISSING UPPER AND LOWER PINCH BOLTS WHICH MAY CAUSE SEPARATION OF THE SHAFT.
THE INTERMEDIATE STEERING SHAFT WAS ASSEMBLED WITH LOOSE OR MISSING UPPER AND LOWER PINCH BOLTS WHICH MAY CAUSE SEPARATION OF THE SHAFT.
THE INTERMEDIATE STEERING SHAFT WAS ASSEMBLED WITH LOOSE OR MISSING UPPER AND LOWER PINCH BOLTS WHICH MAY CAUSE SEPARATION OF THE SHAFT.
THE INTERMEDIATE STEERING SHAFT WAS ASSEMBLED WITH LOOSE OR MISSING UPPER AND LOWER PINCH BOLTS WHICH MAY CAUSE SEPARATION OF THE SHAFT.
VEHICLE FAILS TO CONFORM TO FMVSS NO. 209, SEAT BELT ASSEMBLIES. THE SAFETY BELT OF THE LEFT THIRD ROW SEAT ON THE SIX PASSENGER VAN AND THE CENTER SECOND ROW SEAT OF THE SEVEN PASSENGER VAN MAY LOCK UP AND CANNOT BE WITHDRAWN FROM THE RETRACTOR.
VEHICLE FAILS TO CONFORM TO FMVSS NO. 209, SEAT BELT ASSEMBLIES. THE SAFETY BELT OF THE LEFT THIRD ROW SEAT ON THE SIX PASSENGER VAN AND THE CENTER SECOND ROW SEAT OF THE SEVEN PASSENGER VAN MAY LOCK UP AND CANNOT BE WITHDRAWN FROM THE RETRACTOR.
THE FRONT LEFT BRAKE PIPE CHAFES AGAINST THE POWER STEERING HOSE WHICH WEARS A HOLE IN THE BRAKE PIPE. THIS CAUSES A POTENTIAL LOSS OF BRAKE FLUID RESULTING IN LOSS OF FRONT BRAKE SYSTEM OPERATIONS.
THE FRONT LEFT BRAKE PIPE CHAFES AGAINST THE POWER STEERING HOSE WHICH WEARS A HOLE IN THE BRAKE PIPE. THIS CAUSES A POTENTIAL LOSS OF BRAKE FLUID RESULTING IN LOSS OF FRONT BRAKE SYSTEM OPERATIONS.
THE FRONT LEFT BRAKE PIPE CHAFES AGAINST THE POWER STEERING HOSE WHICH WEARS A HOLE IN THE BRAKE PIPE. THIS CAUSES A POTENTIAL LOSS OF BRAKE FLUID RESULTING IN LOSS OF FRONT BRAKE SYSTEM OPERATIONS.
THE FRONT LEFT BRAKE PIPE CHAFES AGAINST THE POWER STEERING HOSE WHICH WEARS A HOLE IN THE BRAKE PIPE. THIS CAUSES A POTENTIAL LOSS OF BRAKE FLUID RESULTING IN LOSS OF FRONT BRAKE SYSTEM OPERATIONS.
THE SEATS HAVE BEEN ASSEMBLED WITHOUT BOLTS THAT CONNECT THE UPPER SLAVE HINGE TO THE SEAT BACK FRAME, OR WITHOUT BOLTS THAT CONNECT THE SEAT TO THE SEAT ADJUSTER. IN EITHER CASE, THE VEHICLES FAIL TO CONFORM TO FNVSS NO. 207, SEATING SYSTEMS.
THE SEATS HAVE BEEN ASSEMBLED WITHOUT BOLTS THAT CONNECT THE UPPER SLAVE HINGE TO THE SEAT BACK FRAME, OR WITHOUT BOLTS THAT CONNECT THE SEAT TO THE SEAT ADJUSTER. IN EITHER CASE, THE VEHICLES FAIL TO CONFORM TO FNVSS NO. 207, SEATING SYSTEMS.
THE SEATS HAVE BEEN ASSEMBLED WITHOUT BOLTS THAT CONNECT THE UPPER SLAVE HINGE TO THE SEAT BACK FRAME, OR WITHOUT BOLTS THAT CONNECT THE SEAT TO THE SEAT ADJUSTER. IN EITHER CASE, THE VEHICLES FAIL TO CONFORM TO FNVSS NO. 207, SEATING SYSTEMS.
THE SEATS HAVE BEEN ASSEMBLED WITHOUT BOLTS THAT CONNECT THE UPPER SLAVE HINGE TO THE SEAT BACK FRAME, OR WITHOUT BOLTS THAT CONNECT THE SEAT TO THE SEAT ADJUSTER. IN EITHER CASE, THE VEHICLES FAIL TO CONFORM TO FNVSS NO. 207, SEATING SYSTEMS.
THE SEATS HAVE BEEN ASSEMBLED WITHOUT BOLTS THAT CONNECT THE UPPER SLAVE HINGE TO THE SEAT BACK FRAME, OR WITHOUT BOLTS THAT CONNECT THE SEAT TO THE SEAT ADJUSTER. IN EITHER CASE, THE VEHICLES FAIL TO CONFORM TO FNVSS NO. 207, SEATING SYSTEMS.
THE SEATS HAVE BEEN ASSEMBLED WITHOUT BOLTS THAT CONNECT THE UPPER SLAVE HINGE TO THE SEAT BACK FRAME, OR WITHOUT BOLTS THAT CONNECT THE SEAT TO THE SEAT ADJUSTER. IN EITHER CASE, THE VEHICLES FAIL TO CONFORM TO FNVSS NO. 207, SEATING SYSTEMS.
