Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
THE NUTS WHICH FASTEN THE LOWER ARM BALLJOINT TO THE STEERING KNUCKLE MAY NOT HAVE BEEN SECURELY TIGHTENED.
THE NUTS WHICH FASTEN THE LOWER ARM BALLJOINT TO THE STEERING KNUCKLE MAY NOT HAVE BEEN SECURELY TIGHTENED.
THE FUSIBLE LINK, WHICH PROTECTS ELECTRICAL COMPONENTS CONNECTED THROUGH THE IGNITION SWITCH, COULD COME OPEN WHILE REAR WINDOW DEFOGGER IS IN OPERATION. IF TWILIGHT SENTINEL SWITCH IS ON AND HEADLIGHT SWITCH IS OFF, AN OPEN LINK WILL RESULT IN LOSS OF HEADLIGHTS.
THE FUSIBLE LINK, WHICH PROTECTS ELECTRICAL COMPONENTS CONNECTED THROUGH THE IGNITION SWITCH, COULD COME OPEN WHILE REAR WINDOW DEFOGGER IS IN OPERATION. IF TWILIGHT SENTINEL SWITCH IS ON AND HEADLIGHT SWITCH IS OFF, AN OPEN LINK WILL RESULT IN LOSS OF HEADLIGHTS.
DURING WINDSHIELD WIPER OPERATION, THE NOISE SUPPRESION CAPACITOR IN THE WIPER MOTOR RELAY MAY OVERHEAT.
DURING WINDSHIELD WIPER OPERATION, THE NOISE SUPPRESION CAPACITOR IN THE WIPER MOTOR RELAY MAY OVERHEAT.
POSSIBLE FUEL LEAKAGE COULD OCCUR AT THE THROTTLE BODY INJECTION FUEL FEED PIPE CONNECTION ON THE INVOLVED VEHICLES.
SOME OF THE INVOLVED VEHICLES CONTAIN INCORRECT ACCELERATOR CABLE BRACKETS. THIS COULD ALLOW THE CRUISE CONTROL SERVO ROD TO BIND ON THE ACCELERATOR CABLE BRACKET.
SOME OF THE INVOLVED VEHICLES CONTAIN INCORRECT ACCELERATOR CABLE BRACKETS. THIS COULD ALLOW THE CRUISE CONTROL SERVO ROD TO BIND ON THE ACCELERATOR CABLE BRACKET.
UNDER CERTAAIN CONDITIONS, THE HOSE CLAMPS ON THE FUEL TANK FILLER PIPE AND FUEL TANK FILLER VENT PIPE COULD FRACTURE. THE FRACTURE OF THESE CLAMPS COULD CAUSE FUEL LEAKAGE AT ANY OF THE FOUR PIPE TO HOSE CONNECTIONS. LEAKAGE CAN OCCUR DURING REFUELING, OR WHILE DRIVING, IF THE FUEL TANK IS ABOVE 3/4 FULL.
UNDER CERTAIN VEHICLE OPERATING CONDITIONS, THE GOVERNOR WEIGHT RETAINER IN THE INJECTION PUMP MAY FAIL. THE THROTTLE VALVE COULD STICK, PREVENTING RETURN TO IDLE AND SHUT DOWN OF THE ENGINE BY THE DRIVER.
UNDER CERTAIN VEHICLE OPERATING CONDITIONS, THE GOVERNOR WEIGHT RETAINER IN THE INJECTION PUMP MAY FAIL. THE THROTTLE VALVE COULD STICK, PREVENTING RETURN TO IDLE AND SHUT DOWN OF THE ENGINE BY THE DRIVER.
UNDER CERTAIN VEHICLE OPERATING CONDITIONS, THE GOVERNOR WEIGHT RETAINER IN THE INJECTION PUMP MAY FAIL. THE THROTTLE VALVE COULD STICK, PREVENTING RETURN TO IDLE AND SHUT DOWN OF THE ENGINE BY THE DRIVER.
THE INVOLVED VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 210, SEAT BELT ASSEMBLY ANCHORAGES, IN THAT THE DOOR FRAME-TO-BODY CENTER PILLAR INTERLOCK ON THE FRONT SEAT BELTS OF THESE VEHICLES MAY BE MISALIGNED.
THE FRONT LEFT UPPER CONTROL ARM NUTS MAY NOT HAVE BEEN SECURELY TIGHTENED. THE NUTS MAY LOOSEN AND COME OFF AND WITH CONTINUED DRIVING THE CONTROL ARM FRONT BOLT MAY WORK ITS WAY OUT OF POSITION OR BECOME DISPLACED.
THE FRONT LEFT UPPER CONTROL ARM NUTS MAY NOT HAVE BEEN SECURELY TIGHTENED. THE NUTS MAY LOOSEN AND COME OFF AND WITH CONTINUED DRIVING THE CONTROL ARM FRONT BOLT MAY WORK ITS WAY OUT OF POSITION OR BECOME DISPLACED.
TWO SCREWS WHICH SECURE THE SHIFT LINKAGE BRACKET MAY LOOSEN AND FALL OUT. CONSEQUENTLY, THE GEAR POSITION INDICATED ON THE TRANSMISSION SELECTOR MAY DIFFER FROM THE ACTUAL GEAR POSITION OF THE TRANSMISSION. THIS CONSTITUTES A NON-COMPLIANCE TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 102, TRANSMISSION SHIFT LEVER SEQUENCE, STARTER INTERLOCK, AND TRANSMISSION BRAKING EFFECT.
TWO SCREWS WHICH SECURE THE SHIFT LINKAGE BRACKET MAY LOOSEN AND FALL OUT. CONSEQUENTLY, THE GEAR POSITION INDICATED ON THE TRANSMISSION SELECTOR MAY DIFFER FROM THE ACTUAL GEAR POSITION OF THE TRANSMISSION. THIS CONSTITUTES A NON-COMPLIANCE TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 102, TRANSMISSION SHIFT LEVER SEQUENCE, STARTER INTERLOCK, AND TRANSMISSION BRAKING EFFECT.
THE HEADS MAY BREAK OFF THE FRONT OUTBOARD SEAT BELT ANCHOR BOLTS DURING NORMAL VEHICLE OPERATION EVEN UNDER NO LOAD CONDITIONS. THIS IS DUE TO THE COMBINATION OF BOLTS USED, HIGH INSTALLATION TORQUE AND ARRANGEMENT OF THE BODY ANCHORAGE.
THE HEADS MAY BREAK OFF THE FRONT OUTBOARD SEAT BELT ANCHOR BOLTS DURING NORMAL VEHICLE OPERATION EVEN UNDER NO LOAD CONDITIONS. THIS IS DUE TO THE COMBINATION OF BOLTS USED, HIGH INSTALLATION TORQUE AND ARRANGEMENT OF THE BODY ANCHORAGE.
THE HEADS MAY BREAK OFF THE FRONT OUTBOARD SEAT BELT ANCHOR BOLTS DURING NORMAL VEHICLE OPERATION EVEN UNDER NO LOAD CONDITIONS. THIS IS DUE TO THE COMBINATION OF BOLTS USED, HIGH INSTALLATION TORQUE AND ARRANGEMENT OF THE BODY ANCHORAGE.
DUE TO FUEL HOSE CONNECTION DETERIORATION, THE FUEL HOSE CONNECTION FROM THE UNDERBODY FUEL PIPE TO THE FUEL RAIL AT THE REAR OF THE ENGINE MAY LEAK GASOLINE.
THE INVOLVED VEHICLES WERE BUILT WITH AN ACCELERATOR PEDAL HAVING AN EXTENSION, OR RUBBER FLAP, AT THE BOTTOM OF THE PEDAL. THIS PEDAL FLAP COULD BE INADVERTENTLY DISPLACED BY A FLOOR COVERING AND WEDGED UNDER THE ACCELERATOR PEDAL IN A MANNER THAT CAN INFLUENCE THE THROTTLE SETTING AND INCREASE THE ENGINE IDLE RPM.
THE INVOLVED VEHICLES WERE BUILT WITH AN ACCELERATOR PEDAL HAVING AN EXTENSION, OR RUBBER FLAP, AT THE BOTTOM OF THE PEDAL. THIS PEDAL FLAP COULD BE INADVERTENTLY DISPLACED BY A FLOOR COVERING AND WEDGED UNDER THE ACCELERATOR PEDAL IN A MANNER THAT CAN INFLUENCE THE THROTTLE SETTING AND INCREASE THE ENGINE IDLE RPM.
THE INVOLVED VEHICLES WERE BUILT WITH AN ACCELERATOR PEDAL HAVING AN EXTENSION, OR RUBBER FLAP, AT THE BOTTOM OF THE PEDAL. THIS PEDAL FLAP COULD BE INADVERTENTLY DISPLACED BY A FLOOR COVERING AND WEDGED UNDER THE ACCELERATOR PEDAL IN A MANNER THAT CAN INFLUENCE THE THROTTLE SETTING AND INCREASE THE ENGINE IDLE RPM.
THE INVOLVED VEHICLES WERE BUILT WITH AN ACCELERATOR PEDAL HAVING AN EXTENSION, OR RUBBER FLAP, AT THE BOTTOM OF THE PEDAL. THIS PEDAL FLAP COULD BE INADVERTENTLY DISPLACED BY A FLOOR COVERING AND WEDGED UNDER THE ACCELERATOR PEDAL IN A MANNER THAT CAN INFLUENCE THE THROTTLE SETTING AND INCREASE THE ENGINE IDLE RPM.
THE INVOLVED VEHICLES WERE BUILT WITH AN ACCELERATOR PEDAL HAVING AN EXTENSION, OR RUBBER FLAP, AT THE BOTTOM OF THE PEDAL. THIS PEDAL FLAP COULD BE INADVERTENTLY DISPLACED BY A FLOOR COVERING AND WEDGED UNDER THE ACCELERATOR PEDAL IN A MANNER THAT CAN INFLUENCE THE THROTTLE SETTING AND INCREASE THE ENGINE IDLE RPM.
THE INVOLVED VEHICLES WERE BUILT WITH AN ACCELERATOR PEDAL HAVING AN EXTENSION, OR RUBBER FLAP, AT THE BOTTOM OF THE PEDAL. THIS PEDAL FLAP COULD BE INADVERTENTLY DISPLACED BY A FLOOR COVERING AND WEDGED UNDER THE ACCELERATOR PEDAL IN A MANNER THAT CAN INFLUENCE THE THROTTLE SETTING AND INCREASE THE ENGINE IDLE RPM.
VEHICLES FAIL TO COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 105, HYDRAULIC BRAKE SYSTEMS. AN INCORRECT PARKING BRAKE ADJUSTING SPRING WAS INSTALLED ON CERTAIN VEHICLES. THIS MAY CAUSE INTERFERENCE WHEN ATTEMPTING TO APPLY THE PARKING BRAKES.
THE TRANSMISSIONS HAVE BEEN ASSEMBLED WITH A HIGHER THAN NORMAL RETURN SPRING LOAD ON THE TRANSMISSION LOCKING PAWL. WHEN THE PARK POSITION IS SELECTED WITH THE TRANSMISSION SHIFT LEVER, THE PARKING PAWL MAY NOT ENGAGE.
