Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
ON CERTAIN HEAVY DUTY CLASS 8 TRUCKS, THE FORWARD AND/OR REAR DRIVE AXLE UPPER AXLE SEAT CAN BREAK ALLOWING THE AXLE TO SHIFT OUT OF ALIGNMENT.
ON CERTAIN HEAVY DUTY CLASS 8 TRUCKS, THE FORWARD AND/OR REAR DRIVE AXLE UPPER AXLE SEAT CAN BREAK ALLOWING THE AXLE TO SHIFT OUT OF ALIGNMENT.
ON CERTAIN HEAVY DUTY CLASS 8 TRUCKS, THE FORWARD AND/OR REAR DRIVE AXLE UPPER AXLE SEAT CAN BREAK ALLOWING THE AXLE TO SHIFT OUT OF ALIGNMENT.
ON CERTAIN HEAVY DUTY CLASS 8 VEHICLES EQUIPPED WITH ELECTRONIC THROTTLE CONTROL/ACCELERATOR PEDALS SUPPLIED BY WILLIAMS CONTROLS INDUSTRIES, THE WELD ATTACHING THE CLEVIS TO THE PLATE HAS INSUFFICIENT PENETRATION AND COULD ALLOW THE CLEVIS TO SEPARATE FROM THE PLATE.
CERTAIN HEAVY DUTY CLASS 8 TRUCKS FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT. TWO REFLECTORS ARE MISSING FROM THE END OF THE FRAME CROSSMEMBER.
CERTAIN HEAVY DUTY CLASS 8 TRUCKS FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT. TWO REFLECTORS ARE MISSING FROM THE END OF THE FRAME CROSSMEMBER.
EQUIPMENT DESCRIPTION: AFTERMARKET REPLACEMENT SEAT BELT ASSEMBLIES INSTALLED IN THE VOLVO, F7 MODEL, CLASS 7 AND 8 VEHICLES BETWEEN SEPTEMBER 1981 AND MARCH 1986. THE AFFECTED BELTS CAN BE IDENTIFIED BY PART NUMBER 1088593 OR V1088593. THESE SEAT BELT ASSEMBLIES DO NOT MEET THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD 210, SEAT BELT ASSEMBLY ANCHORAGES.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS BUILT WITH A STEERABLE AUXILIARY AXLE AND EQUIPPED WITH CERTAIN MERITOR-WABCO BRAKE SYSTEM TWO AND FOUR PORT RELAY VALVES. THE VALVE MAY STICK OPEN WHEN A HIGH-PRESSURE APPLICATION IS RELEASED.
VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS BUILT WITH A STEERABLE AUXILIARY AXLE AND EQUIPPED WITH CERTAIN MERITOR-WABCO BRAKE SYSTEM TWO AND FOUR PORT RELAY VALVES. THE VALVE MAY STICK OPEN WHEN A HIGH-PRESSURE APPLICATION IS RELEASED.
VEHICLE DESCRIPTION: HEAVY DUTY 6X4 TRUCKS EQUIPPED WITH CHALMERS 800 SERIES SUSPENSION KITS. THESE SUSPENSION KITS MAY HAVE INSUFFICIENT PENETRATION OF THE WELD ATTACHING THE TORQUE ROD EYE TO THE TORQUE ROD TUBE.
VEHICLE DESCRIPTION: HEAVY DUTY 6X4 TRUCKS EQUIPPED WITH CHALMERS 800 SERIES SUSPENSION KITS. THESE SUSPENSION KITS MAY HAVE INSUFFICIENT PENETRATION OF THE WELD ATTACHING THE TORQUE ROD EYE TO THE TORQUE ROD TUBE.
VEHICLE DESCRIPTION: HEAVY DUTY 6X4 TRUCKS EQUIPPED WITH CHALMERS 800 SERIES SUSPENSION KITS. THESE SUSPENSION KITS MAY HAVE INSUFFICIENT PENETRATION OF THE WELD ATTACHING THE TORQUE ROD EYE TO THE TORQUE ROD TUBE.
VEHICLE DESCRIPTION: HEAVY DUTY CLASS 8 TRUCKS. THE LOWER STEERING SHAFT MAY SIDE-LOAD THE STEERING GEAR INPUT SHAFT. THIS CONDITION COULD RESULT IN NON-UNIFORM STEERING WHEEL EFFORTS WHEN TURNING THE STEERING WHEEL. IN ADDITION, ONCE THE STEERING WHEEL TURN IS INITIATED, THE VEHICLE MAY CONTINUE TURNING WITHOUT RETURNING TO THE STRAIGHT AHEAD POSITION WITH DRIVER EFFORT.
VEHICLE DESCRIPTION: HEAVY DUTY CLASS 8 TRUCKS. THE LOWER STEERING SHAFT MAY SIDE-LOAD THE STEERING GEAR INPUT SHAFT. THIS CONDITION COULD RESULT IN NON-UNIFORM STEERING WHEEL EFFORTS WHEN TURNING THE STEERING WHEEL. IN ADDITION, ONCE THE STEERING WHEEL TURN IS INITIATED, THE VEHICLE MAY CONTINUE TURNING WITHOUT RETURNING TO THE STRAIGHT AHEAD POSITION WITH DRIVER EFFORT.
VEHICLE DESCRIPTION: HEAVY DUTY CLASS 8 TRUCKS. THE WRONG STEERING COLUMN TO STEERING GEAR SHAFT MAY HAVE BEEN INSTALLED IN THESE VEHICLES. USING THE SHORTER VNM STEERING SHAFT COULD RESULT IN STEERING SHAFT BEING OPERATED (STEERING COLUMN EXTENDED ADJUSTMENT) OUTSIDE THE NORMAL OPERATING RANGE OF THE STEERING SHAFT.
VEHICLE DESCRIPTION: SEDAN AND WAGON PASSENGER VEHICLES. A DIODE IN THE ELECTRONIC CLIMATE CONTROL SYSTEM MAY HAVE A REDUCED SERVICE LIFE.
VEHICLE DESCRIPTION: SEDAN AND WAGON PASSENGER VEHICLES. A DIODE IN THE ELECTRONIC CLIMATE CONTROL SYSTEM MAY HAVE A REDUCED SERVICE LIFE.
VEHICLE DESCRIPTION: HEAVY DUTY, CLASS 8, TRUCKS EQUIPPED WITH TIE ROD ASSEMBLIES CONTAINING 24-DL MODEL BALL SOCKETS AND MANUFACTURED BY TRW. CERTAIN OF THE TIE ROD BALL-SOCKET BEARINGS HAVE A BELOW-SPECIFICATION CASE DEPTH AND/OR HARDNESS, WHICH CAN LEAD TO PREMATURE WEAR OF THE SOCKET.
VEHICLE DESCRIPTION: HEAVY DUTY, CLASS 8, TRUCKS EQUIPPED WITH TIE ROD ASSEMBLIES CONTAINING 24-DL MODEL BALL SOCKETS AND MANUFACTURED BY TRW. CERTAIN OF THE TIE ROD BALL-SOCKET BEARINGS HAVE A BELOW-SPECIFICATION CASE DEPTH AND/OR HARDNESS, WHICH CAN LEAD TO PREMATURE WEAR OF THE SOCKET.
VEHICLE DESCRIPTION: HEAVY DUTY, CLASS 8, TRUCKS EQUIPPED WITH TIE ROD ASSEMBLIES CONTAINING 24-DL MODEL BALL SOCKETS AND MANUFACTURED BY TRW. CERTAIN OF THE TIE ROD BALL-SOCKET BEARINGS HAVE A BELOW-SPECIFICATION CASE DEPTH AND/OR HARDNESS, WHICH CAN LEAD TO PREMATURE WEAR OF THE SOCKET.
VEHICLE DESCRIPTION: HEAVY DUTY, CLASS 8, TRUCKS EQUIPPED WITH TIE ROD ASSEMBLIES CONTAINING 24-DL MODEL BALL SOCKETS AND MANUFACTURED BY TRW. CERTAIN OF THE TIE ROD BALL-SOCKET BEARINGS HAVE A BELOW-SPECIFICATION CASE DEPTH AND/OR HARDNESS, WHICH CAN LEAD TO PREMATURE WEAR OF THE SOCKET.
VEHICLE DESCRIPTION: HEAVY DUTY, CLASS 8, TRUCKS EQUIPPED WITH TIE ROD ASSEMBLIES CONTAINING 24-DL MODEL BALL SOCKETS AND MANUFACTURED BY TRW. CERTAIN OF THE TIE ROD BALL-SOCKET BEARINGS HAVE A BELOW-SPECIFICATION CASE DEPTH AND/OR HARDNESS, WHICH CAN LEAD TO PREMATURE WEAR OF THE SOCKET.
VEHICLE DESCRIPTION: HEAVY DUTY, CLASS 8, TRUCKS EQUIPPED WITH TIE ROD ASSEMBLIES CONTAINING 24-DL MODEL BALL SOCKETS AND MANUFACTURED BY TRW. CERTAIN OF THE TIE ROD BALL-SOCKET BEARINGS HAVE A BELOW-SPECIFICATION CASE DEPTH AND/OR HARDNESS, WHICH CAN LEAD TO PREMATURE WEAR OF THE SOCKET.
VEHICLE DESCRIPTION: SEDANS AND WAGONS. THE REAR OUTBOARD SEAT BELT ANCHORAGE BOLTS MAY HAVE BEEN INCORRECTLY TIGHTENED.
VEHICLE DESCRIPTION: SEDANS AND WAGONS. THE REAR OUTBOARD SEAT BELT ANCHORAGE BOLTS MAY HAVE BEEN INCORRECTLY TIGHTENED.
VEHICLE DESCRIPTION: WAGONS. THE BOLTED JOINT, USED FOR ATTACHING THE BRACKET THAT IS PART OF THE INSTALLATION HARDWARE FOR THE ISOFIX-TYPE CHILD RESTRAINT, MAY HAVE BEEN INCORRECTLY TIGHTENED.
VEHICLE DESCRIPTION: HEAVY DUTY CLASS 8 VEHICLES. UNDER CERTAIN OPERATING CONDITIONS, THE WEIGHT CERTIFICATION LABEL WHICH CONTAINS FRONT GROSS AXLE WEIGHT RATING (GAWR) INFORMATION PURSUANT TO THE REQUIREMENTS OF FMVSS NO. 120, TIRE SELECTION AND RIMS FOR MOTOR VEHICLES OTHER THAN PASSENGER CARS, DOES NOT ACCURATELY REFLECT THE ACTUAL FRONT GROSS AXLE WEIGHT.
VEHICLE DESCRIPTION: HEAVY DUTY CLASS 8 VEHICLES. UNDER CERTAIN OPERATING CONDITIONS, THE WEIGHT CERTIFICATION LABEL WHICH CONTAINS FRONT GROSS AXLE WEIGHT RATING (GAWR) INFORMATION PURSUANT TO THE REQUIREMENTS OF FMVSS NO. 120, TIRE SELECTION AND RIMS FOR MOTOR VEHICLES OTHER THAN PASSENGER CARS, DOES NOT ACCURATELY REFLECT THE ACTUAL FRONT GROSS AXLE WEIGHT.
VEHICLE DESCRIPTION: HEAVY DUTY CLASS 8 VEHICLES. UNDER CERTAIN OPERATING CONDITIONS, THE WEIGHT CERTIFICATION LABEL WHICH CONTAINS FRONT GROSS AXLE WEIGHT RATING (GAWR) INFORMATION PURSUANT TO THE REQUIREMENTS OF FMVSS NO. 120, TIRE SELECTION AND RIMS FOR MOTOR VEHICLES OTHER THAN PASSENGER CARS, DOES NOT ACCURATELY REFLECT THE ACTUAL FRONT GROSS AXLE WEIGHT.
VEHICLE DESCRIPTION: CLASS 8 HEAVY DUTY, AXLE BACK MODEL VEHICLES. THE DESIGN OF THE LOWER STEERING COLUMN SHAFT UNIVERSAL JOINT BOOT COULD ALLOW THE BOOT TO GET ENTANGLED IN THE UNIVERSAL JOINT.
