Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
INCORRECT HEAD RESTRAINTS MAY HAVE BEEN INSTALLED ON THE INVOLVED VEHICLES. THIS FAILS TO COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 201, OCCUPANT PROTECTION IN INTERIOR IMPACTS.
THE INTERMEDIATE SHAFT COUPLING ON THE INVOLVED VEHICLES MAY HAVE BEEN MACHINED OVERSIZED IN THE SERRATION AREA WHERE IT ATTACHES TO THE STEERING COLUMN. THIS WOULD PREVENT THE COUPLING FROM PROPERLY TIGHTENING ON THE SHAFT WHEN THE CLAMP AND PINCH BOLT WERE INSTALLED.
THE REAR WHEEL MOUNTING BOLTS ON THE AFFECTED VEHICLES, ARE BRITTLE AND THEREFORE MAY FRACTURE. THIS BRITTLENESS IS DUE TO IMPROPER HEAT TREATMENT DURING MANUFACTURE. IF THE BOLTS BREAK, THE TIRE AND WHEEL ASSEMBLY MAY SEPARATE FROM THE VEHICLE.
THE REAR WHEEL MOUNTING BOLTS ON THE AFFECTED VEHICLES, ARE BRITTLE AND THEREFORE MAY FRACTURE. THIS BRITTLENESS IS DUE TO IMPROPER HEAT TREATMENT DURING MANUFACTURE. IF THE BOLTS BREAK, THE TIRE AND WHEEL ASSEMBLY MAY SEPARATE FROM THE VEHICLE.
THE REAR WHEEL MOUNTING BOLTS ON THE AFFECTED VEHICLES, ARE BRITTLE AND THEREFORE MAY FRACTURE. THIS BRITTLENESS IS DUE TO IMPROPER HEAT TREATMENT DURING MANUFACTURE. IF THE BOLTS BREAK, THE TIRE AND WHEEL ASSEMBLY MAY SEPARATE FROM THE VEHICLE.
THE REAR BRAKE WHEEL CYLINDER RETAINER ON THE INVOLVED VEHICLES MAY NOT HAVE BEEN PROPERLY INSTALLED. SHOULD THE WHEEL CYLINDER RETAINER BECOME COMPLETELY DISENGAGED, THE WHEEL CYLINDER COULD MOVE OUTBOARD CAUSING A LOSS OF BRAKE FLUID AND A LOSS OF REAR BRAKING ACTION.
THE REAR BRAKE WHEEL CYLINDER RETAINER ON THE INVOLVED VEHICLES MAY NOT HAVE BEEN PROPERLY INSTALLED. SHOULD THE WHEEL CYLINDER RETAINER BECOME COMPLETELY DISENGAGED, THE WHEEL CYLINDER COULD MOVE OUTBOARD CAUSING A LOSS OF BRAKE FLUID AND A LOSS OF REAR BRAKING ACTION.
THE REAR BRAKE WHEEL CYLINDER RETAINER ON THE INVOLVED VEHICLES MAY NOT HAVE BEEN PROPERLY INSTALLED. SHOULD THE WHEEL CYLINDER RETAINER BECOME COMPLETELY DISENGAGED, THE WHEEL CYLINDER COULD MOVE OUTBOARD CAUSING A LOSS OF BRAKE FLUID AND A LOSS OF REAR BRAKING ACTION.
THE REAR AXLE SHAFTS ON THE INVOLVED VEHICLES MAY HAVE A FLAW IN THE METAL. AS A RESULT, THE SHAFT MAY BREAK, WHICH WOULD ALLOW THE TIRE AND WHEEL ASSEMBLY TO SEPARATE FROM THE VEHICLE.
THE REAR AXLE SHAFTS ON THE INVOLVED VEHICLES MAY HAVE A FLAW IN THE METAL. AS A RESULT, THE SHAFT MAY BREAK, WHICH WOULD ALLOW THE TIRE AND WHEEL ASSEMBLY TO SEPARATE FROM THE VEHICLE.
THE REAR AXLE SHAFTS ON THE INVOLVED VEHICLES MAY HAVE A FLAW IN THE METAL. AS A RESULT, THE SHAFT MAY BREAK, WHICH WOULD ALLOW THE TIRE AND WHEEL ASSEMBLY TO SEPARATE FROM THE VEHICLE.
THE REAR AXLE SHAFTS ON THE INVOLVED VEHICLES MAY HAVE A FLAW IN THE METAL. AS A RESULT, THE SHAFT MAY BREAK, WHICH WOULD ALLOW THE TIRE AND WHEEL ASSEMBLY TO SEPARATE FROM THE VEHICLE.
THE INVOLVED VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 204, STEERING CONTROL REARWARD DISPLACEMENT. THE CONSTRUCTION OF THE CLUTCH PEDAL BRACKET COULD PERMIT REARWARD DISPLACEMENT OF STEERING CONTROL INTO PASSENGER COMPARTMENT IN EXCESS OF THAT ALLOWABLE BY THE STANDARD DURING THE 30 MPH BARRIER CRASH TEST.
ON THE INVOLVED VEHICLES, THE INCORRECT FUEL HOSE PIPE WAS INSTALLED. CONSEQUENTLY, THE NEEDED SPECIAL REINFORCEMENT, USED TO HELP PREVENT RUPTURE OF THE HOSE AND SPILLAGE OF FUEL RESULTING FROM AN IMPACT FROM THE SIDE, WAS OMITTED. THIS WOULD CONSTITUTE A NON-COMPLIANCE WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 310, FUEL SYSTEM INTEGRITY.
ON THE INVOLVED VEHICLES, THE INCORRECT STEERING LINKAGE ASSEMBLY MAY HAVE BEEN INSTALLED. AS A RESULT, THE RIGHT-HAND STEERING TIE ROD MIGHT INTERFERE WITH THE INTERMEDIATE ROD. THIS COULD CAUSE THE CONNECTION TO FAIL DUE TO EXCESSIVE STRESS AT THAT POINT.
ON THE INVOLVED VEHICLES, THE INCORRECT STEERING LINKAGE ASSEMBLY MAY HAVE BEEN INSTALLED. AS A RESULT, THE RIGHT-HAND STEERING TIE ROD MIGHT INTERFERE WITH THE INTERMEDIATE ROD. THIS COULD CAUSE THE CONNECTION TO FAIL DUE TO EXCESSIVE STRESS AT THAT POINT.
ON THE INVOLVED VEHICLES, THE INCORRECT STEERING LINKAGE ASSEMBLY MAY HAVE BEEN INSTALLED. AS A RESULT, THE RIGHT-HAND STEERING TIE ROD MIGHT INTERFERE WITH THE INTERMEDIATE ROD. THIS COULD CAUSE THE CONNECTION TO FAIL DUE TO EXCESSIVE STRESS AT THAT POINT.
ON THE INVOLVED VEHICLES, THE INCORRECT STEERING LINKAGE ASSEMBLY MAY HAVE BEEN INSTALLED. AS A RESULT, THE RIGHT-HAND STEERING TIE ROD MIGHT INTERFERE WITH THE INTERMEDIATE ROD. THIS COULD CAUSE THE CONNECTION TO FAIL DUE TO EXCESSIVE STRESS AT THAT POINT.
ON THE INVOLVED VEHICLES, THE INCORRECT STEERING LINKAGE ASSEMBLY MAY HAVE BEEN INSTALLED. AS A RESULT, THE RIGHT-HAND STEERING TIE ROD MIGHT INTERFERE WITH THE INTERMEDIATE ROD. THIS COULD CAUSE THE CONNECTION TO FAIL DUE TO EXCESSIVE STRESS AT THAT POINT.
