Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT. THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.
SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT. THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.
MITSUBISHI IS RECALLING 39,711 MY 2008-2009 OUTLANDER AND LACER VEHICLES. INCORRECT MATERIAL COMPOSITION OF THE BRAKE BOOSTER CHECK VALVE MAY CAUSE THE CHECK VALVE TO STICK CLOSED WHEN THE ENGINE IS SHUT OFF. WHEN THE VEHICLE IS RE-STARTED AND PUT INTO MOTION, UNDER CERTAIN DRIVING CONDITIONS (VERY SLOW VEHICLE MANEUVERS), THERE MAY BE INSUFFICIENT INITIAL BRAKING ASSIST.
MITSUBISHI IS RECALLING 39,711 MY 2008-2009 OUTLANDER AND LACER VEHICLES. INCORRECT MATERIAL COMPOSITION OF THE BRAKE BOOSTER CHECK VALVE MAY CAUSE THE CHECK VALVE TO STICK CLOSED WHEN THE ENGINE IS SHUT OFF. WHEN THE VEHICLE IS RE-STARTED AND PUT INTO MOTION, UNDER CERTAIN DRIVING CONDITIONS (VERY SLOW VEHICLE MANEUVERS), THERE MAY BE INSUFFICIENT INITIAL BRAKING ASSIST.
MITSUBISHI IS RECALLING 39,711 MY 2008-2009 OUTLANDER AND LACER VEHICLES. INCORRECT MATERIAL COMPOSITION OF THE BRAKE BOOSTER CHECK VALVE MAY CAUSE THE CHECK VALVE TO STICK CLOSED WHEN THE ENGINE IS SHUT OFF. WHEN THE VEHICLE IS RE-STARTED AND PUT INTO MOTION, UNDER CERTAIN DRIVING CONDITIONS (VERY SLOW VEHICLE MANEUVERS), THERE MAY BE INSUFFICIENT INITIAL BRAKING ASSIST.
MITSUBISHI IS RECALLING 39,711 MY 2008-2009 OUTLANDER AND LACER VEHICLES. INCORRECT MATERIAL COMPOSITION OF THE BRAKE BOOSTER CHECK VALVE MAY CAUSE THE CHECK VALVE TO STICK CLOSED WHEN THE ENGINE IS SHUT OFF. WHEN THE VEHICLE IS RE-STARTED AND PUT INTO MOTION, UNDER CERTAIN DRIVING CONDITIONS (VERY SLOW VEHICLE MANEUVERS), THERE MAY BE INSUFFICIENT INITIAL BRAKING ASSIST.
MITSUBISHI IS RECALLING 21,493 MY 2007-2008 OUTLANDER VEHICLES EQUIPPED WITH LED TYPE STOP LAMPS AND DISTRIBUTED IN THE UNITED STATES AND PUERTO RICO. THE BRAKE LAMP SWITCH MAY MALFUNCTION AND CAUSE THE STOP LAMPS TO NOT ILLUMINATE DURING BRAKE APPLICATION.
MITSUBISHI IS RECALLING 21,493 MY 2007-2008 OUTLANDER VEHICLES EQUIPPED WITH LED TYPE STOP LAMPS AND DISTRIBUTED IN THE UNITED STATES AND PUERTO RICO. THE BRAKE LAMP SWITCH MAY MALFUNCTION AND CAUSE THE STOP LAMPS TO NOT ILLUMINATE DURING BRAKE APPLICATION.
MITSUBISHI IS RECALLING 45,988 MY 2005-2007 ENDEAVOR, GALANT, ECLIPSE COUPE, AND MY 2007 ECLIPSE SPYDER VEHICLES. THE BRACKET THAT IS THE ATTACHMENT POINT FOR THE LEFT REAR FUEL TANK MOUNTING STRAP MAY HAVE BEEN IMPROPERLY FORMED DURING A METAL STAMPING PROCESS. THE PROCESS MAY HAVE CAUSED THE METAL TO HAVE A SPLIT IN THE AREA WHERE THE BOLT THAT HOLDS ONE OF THE TWO FUEL TANK STRAPS TO THE UNDERSIDE OF THE VEHICLE IS LOCATED. IN THE EVENT THE FUEL TANK IS FULL AND THE VEHICLE IS SUBJECT TO A SEVERE COLLISION, THE BRACKET MAY BREAK AND ALLOW THE FUEL TANK TO DROP DOWN, POSSIBLY CAUSING A FUEL LEAK.
MITSUBISHI IS RECALLING 45,988 MY 2005-2007 ENDEAVOR, GALANT, ECLIPSE COUPE, AND MY 2007 ECLIPSE SPYDER VEHICLES. THE BRACKET THAT IS THE ATTACHMENT POINT FOR THE LEFT REAR FUEL TANK MOUNTING STRAP MAY HAVE BEEN IMPROPERLY FORMED DURING A METAL STAMPING PROCESS. THE PROCESS MAY HAVE CAUSED THE METAL TO HAVE A SPLIT IN THE AREA WHERE THE BOLT THAT HOLDS ONE OF THE TWO FUEL TANK STRAPS TO THE UNDERSIDE OF THE VEHICLE IS LOCATED. IN THE EVENT THE FUEL TANK IS FULL AND THE VEHICLE IS SUBJECT TO A SEVERE COLLISION, THE BRACKET MAY BREAK AND ALLOW THE FUEL TANK TO DROP DOWN, POSSIBLY CAUSING A FUEL LEAK.
MITSUBISHI IS RECALLING 45,988 MY 2005-2007 ENDEAVOR, GALANT, ECLIPSE COUPE, AND MY 2007 ECLIPSE SPYDER VEHICLES. THE BRACKET THAT IS THE ATTACHMENT POINT FOR THE LEFT REAR FUEL TANK MOUNTING STRAP MAY HAVE BEEN IMPROPERLY FORMED DURING A METAL STAMPING PROCESS. THE PROCESS MAY HAVE CAUSED THE METAL TO HAVE A SPLIT IN THE AREA WHERE THE BOLT THAT HOLDS ONE OF THE TWO FUEL TANK STRAPS TO THE UNDERSIDE OF THE VEHICLE IS LOCATED. IN THE EVENT THE FUEL TANK IS FULL AND THE VEHICLE IS SUBJECT TO A SEVERE COLLISION, THE BRACKET MAY BREAK AND ALLOW THE FUEL TANK TO DROP DOWN, POSSIBLY CAUSING A FUEL LEAK.
MITSUBISHI IS RECALLING 45,988 MY 2005-2007 ENDEAVOR, GALANT, ECLIPSE COUPE, AND MY 2007 ECLIPSE SPYDER VEHICLES. THE BRACKET THAT IS THE ATTACHMENT POINT FOR THE LEFT REAR FUEL TANK MOUNTING STRAP MAY HAVE BEEN IMPROPERLY FORMED DURING A METAL STAMPING PROCESS. THE PROCESS MAY HAVE CAUSED THE METAL TO HAVE A SPLIT IN THE AREA WHERE THE BOLT THAT HOLDS ONE OF THE TWO FUEL TANK STRAPS TO THE UNDERSIDE OF THE VEHICLE IS LOCATED. IN THE EVENT THE FUEL TANK IS FULL AND THE VEHICLE IS SUBJECT TO A SEVERE COLLISION, THE BRACKET MAY BREAK AND ALLOW THE FUEL TANK TO DROP DOWN, POSSIBLY CAUSING A FUEL LEAK.
MITSUBISHI IS RECALLING 45,988 MY 2005-2007 ENDEAVOR, GALANT, ECLIPSE COUPE, AND MY 2007 ECLIPSE SPYDER VEHICLES. THE BRACKET THAT IS THE ATTACHMENT POINT FOR THE LEFT REAR FUEL TANK MOUNTING STRAP MAY HAVE BEEN IMPROPERLY FORMED DURING A METAL STAMPING PROCESS. THE PROCESS MAY HAVE CAUSED THE METAL TO HAVE A SPLIT IN THE AREA WHERE THE BOLT THAT HOLDS ONE OF THE TWO FUEL TANK STRAPS TO THE UNDERSIDE OF THE VEHICLE IS LOCATED. IN THE EVENT THE FUEL TANK IS FULL AND THE VEHICLE IS SUBJECT TO A SEVERE COLLISION, THE BRACKET MAY BREAK AND ALLOW THE FUEL TANK TO DROP DOWN, POSSIBLY CAUSING A FUEL LEAK.
MITSUBISHI IS RECALLING 45,988 MY 2005-2007 ENDEAVOR, GALANT, ECLIPSE COUPE, AND MY 2007 ECLIPSE SPYDER VEHICLES. THE BRACKET THAT IS THE ATTACHMENT POINT FOR THE LEFT REAR FUEL TANK MOUNTING STRAP MAY HAVE BEEN IMPROPERLY FORMED DURING A METAL STAMPING PROCESS. THE PROCESS MAY HAVE CAUSED THE METAL TO HAVE A SPLIT IN THE AREA WHERE THE BOLT THAT HOLDS ONE OF THE TWO FUEL TANK STRAPS TO THE UNDERSIDE OF THE VEHICLE IS LOCATED. IN THE EVENT THE FUEL TANK IS FULL AND THE VEHICLE IS SUBJECT TO A SEVERE COLLISION, THE BRACKET MAY BREAK AND ALLOW THE FUEL TANK TO DROP DOWN, POSSIBLY CAUSING A FUEL LEAK.
MITSUBISHI IS RECALLING 45,988 MY 2005-2007 ENDEAVOR, GALANT, ECLIPSE COUPE, AND MY 2007 ECLIPSE SPYDER VEHICLES. THE BRACKET THAT IS THE ATTACHMENT POINT FOR THE LEFT REAR FUEL TANK MOUNTING STRAP MAY HAVE BEEN IMPROPERLY FORMED DURING A METAL STAMPING PROCESS. THE PROCESS MAY HAVE CAUSED THE METAL TO HAVE A SPLIT IN THE AREA WHERE THE BOLT THAT HOLDS ONE OF THE TWO FUEL TANK STRAPS TO THE UNDERSIDE OF THE VEHICLE IS LOCATED. IN THE EVENT THE FUEL TANK IS FULL AND THE VEHICLE IS SUBJECT TO A SEVERE COLLISION, THE BRACKET MAY BREAK AND ALLOW THE FUEL TANK TO DROP DOWN, POSSIBLY CAUSING A FUEL LEAK.
MITSUBISHI IS RECALLING 45,988 MY 2005-2007 ENDEAVOR, GALANT, ECLIPSE COUPE, AND MY 2007 ECLIPSE SPYDER VEHICLES. THE BRACKET THAT IS THE ATTACHMENT POINT FOR THE LEFT REAR FUEL TANK MOUNTING STRAP MAY HAVE BEEN IMPROPERLY FORMED DURING A METAL STAMPING PROCESS. THE PROCESS MAY HAVE CAUSED THE METAL TO HAVE A SPLIT IN THE AREA WHERE THE BOLT THAT HOLDS ONE OF THE TWO FUEL TANK STRAPS TO THE UNDERSIDE OF THE VEHICLE IS LOCATED. IN THE EVENT THE FUEL TANK IS FULL AND THE VEHICLE IS SUBJECT TO A SEVERE COLLISION, THE BRACKET MAY BREAK AND ALLOW THE FUEL TANK TO DROP DOWN, POSSIBLY CAUSING A FUEL LEAK.
MITSUBISHI IS RECALLING 45,988 MY 2005-2007 ENDEAVOR, GALANT, ECLIPSE COUPE, AND MY 2007 ECLIPSE SPYDER VEHICLES. THE BRACKET THAT IS THE ATTACHMENT POINT FOR THE LEFT REAR FUEL TANK MOUNTING STRAP MAY HAVE BEEN IMPROPERLY FORMED DURING A METAL STAMPING PROCESS. THE PROCESS MAY HAVE CAUSED THE METAL TO HAVE A SPLIT IN THE AREA WHERE THE BOLT THAT HOLDS ONE OF THE TWO FUEL TANK STRAPS TO THE UNDERSIDE OF THE VEHICLE IS LOCATED. IN THE EVENT THE FUEL TANK IS FULL AND THE VEHICLE IS SUBJECT TO A SEVERE COLLISION, THE BRACKET MAY BREAK AND ALLOW THE FUEL TANK TO DROP DOWN, POSSIBLY CAUSING A FUEL LEAK.
MITSUBISHI IS RECALLING 45,988 MY 2005-2007 ENDEAVOR, GALANT, ECLIPSE COUPE, AND MY 2007 ECLIPSE SPYDER VEHICLES. THE BRACKET THAT IS THE ATTACHMENT POINT FOR THE LEFT REAR FUEL TANK MOUNTING STRAP MAY HAVE BEEN IMPROPERLY FORMED DURING A METAL STAMPING PROCESS. THE PROCESS MAY HAVE CAUSED THE METAL TO HAVE A SPLIT IN THE AREA WHERE THE BOLT THAT HOLDS ONE OF THE TWO FUEL TANK STRAPS TO THE UNDERSIDE OF THE VEHICLE IS LOCATED. IN THE EVENT THE FUEL TANK IS FULL AND THE VEHICLE IS SUBJECT TO A SEVERE COLLISION, THE BRACKET MAY BREAK AND ALLOW THE FUEL TANK TO DROP DOWN, POSSIBLY CAUSING A FUEL LEAK.
MITSUBISHI IS RECALLING 73,000 MY 2004-2006 GALLANT PASSENGER VEHICLES. DURING VEHICLE USE, THE IGNITION KEY INTERLOCK CABLE (WHICH IS A COMPONENT OF THE INTERLOCK SYSTEM) MAY ALLOW THE INTERLOCKING CAM TO FALL FORWARD AND ALLOW THE IGNITION KEY TO BE REMOVED FROM THE IGNITION SWITCH WHEN THE GEARSHIFT MECHANISM IS NOT IN THE PARK POSITION.
MITSUBISHI IS RECALLING 73,000 MY 2004-2006 GALLANT PASSENGER VEHICLES. DURING VEHICLE USE, THE IGNITION KEY INTERLOCK CABLE (WHICH IS A COMPONENT OF THE INTERLOCK SYSTEM) MAY ALLOW THE INTERLOCKING CAM TO FALL FORWARD AND ALLOW THE IGNITION KEY TO BE REMOVED FROM THE IGNITION SWITCH WHEN THE GEARSHIFT MECHANISM IS NOT IN THE PARK POSITION.
MITSUBISHI IS RECALLING 120,000 MY 2004-2006 ENDEAVOR PASSENGER VEHICLES. DURING VEHICLE USE, THE IGNITION KEY INTERLOCK CABLE (WHICH IS A COMPONENT OF THE INTERLOCK SYSTEM) MAY ALLOW THE INTERLOCKING CAM TO FALL FORWARD AND ALLOW THE IGNITION KEY TO BE REMOVED FROM THE IGNITION SWITCH WHEN THE GEARSHIFT MECHANISM IS NOT IN THE PARK POSITION.
MITSUBISHI IS RECALLING 120,000 MY 2004-2006 ENDEAVOR PASSENGER VEHICLES. DURING VEHICLE USE, THE IGNITION KEY INTERLOCK CABLE (WHICH IS A COMPONENT OF THE INTERLOCK SYSTEM) MAY ALLOW THE INTERLOCKING CAM TO FALL FORWARD AND ALLOW THE IGNITION KEY TO BE REMOVED FROM THE IGNITION SWITCH WHEN THE GEARSHIFT MECHANISM IS NOT IN THE PARK POSITION.
MITSUBISHI IS RECALLING 120,000 MY 2004-2006 ENDEAVOR PASSENGER VEHICLES. DURING VEHICLE USE, THE IGNITION KEY INTERLOCK CABLE (WHICH IS A COMPONENT OF THE INTERLOCK SYSTEM) MAY ALLOW THE INTERLOCKING CAM TO FALL FORWARD AND ALLOW THE IGNITION KEY TO BE REMOVED FROM THE IGNITION SWITCH WHEN THE GEARSHIFT MECHANISM IS NOT IN THE PARK POSITION.
MITSUBISHI IS RECALLING 120,000 MY 2004-2006 ENDEAVOR PASSENGER VEHICLES. DURING VEHICLE USE, THE IGNITION KEY INTERLOCK CABLE (WHICH IS A COMPONENT OF THE INTERLOCK SYSTEM) MAY ALLOW THE INTERLOCKING CAM TO FALL FORWARD AND ALLOW THE IGNITION KEY TO BE REMOVED FROM THE IGNITION SWITCH WHEN THE GEARSHIFT MECHANISM IS NOT IN THE PARK POSITION.
MITSUBISHI IS RECALLING 120,000 MY 2004-2006 ENDEAVOR PASSENGER VEHICLES. DURING VEHICLE USE, THE IGNITION KEY INTERLOCK CABLE (WHICH IS A COMPONENT OF THE INTERLOCK SYSTEM) MAY ALLOW THE INTERLOCKING CAM TO FALL FORWARD AND ALLOW THE IGNITION KEY TO BE REMOVED FROM THE IGNITION SWITCH WHEN THE GEARSHIFT MECHANISM IS NOT IN THE PARK POSITION.
MITSUBISHI IS RECALLING 5,400 MY 2007-2008 OUTLANDER PASSENGER VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, KENTUCKY, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, VIRGINIA, WEST VIRGINIA, WISCONSIN, AND THE DISTRICT OF COLUMBIA. FOR VEHICLES WITHOUT AN ELECTRIC POWER SEAT, THE FLOOR HARNESS CONNECTOR FOR THE POWER SEAT IS PLACED DIRECTLY ON THE FLOORBOARD UNDERNEATH THE CARPETING (VEHICLES WITH POWER SEATS ALREADY HAVE THE HARNESS ELEVATED). IF A VEHICLE OCCUPANT ENTERS THE VEHICLE WITH A SUFFICIENT AMOUNT OF SNOW ON THEIR FEET CONTAINING ROAD SALT, IT IS POSSIBLE FOR THE MELTED SNOW MIXTURE TO SOAK THE CARPET AND ALLOW THE SALT-WATER SOLUTION TO COME INTO CONTACT WITH THE UNUSED POWER SEAT HARNESS CONNECTOR.
MITSUBISHI IS RECALLING 5,400 MY 2007-2008 OUTLANDER PASSENGER VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, KENTUCKY, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, VIRGINIA, WEST VIRGINIA, WISCONSIN, AND THE DISTRICT OF COLUMBIA. FOR VEHICLES WITHOUT AN ELECTRIC POWER SEAT, THE FLOOR HARNESS CONNECTOR FOR THE POWER SEAT IS PLACED DIRECTLY ON THE FLOORBOARD UNDERNEATH THE CARPETING (VEHICLES WITH POWER SEATS ALREADY HAVE THE HARNESS ELEVATED). IF A VEHICLE OCCUPANT ENTERS THE VEHICLE WITH A SUFFICIENT AMOUNT OF SNOW ON THEIR FEET CONTAINING ROAD SALT, IT IS POSSIBLE FOR THE MELTED SNOW MIXTURE TO SOAK THE CARPET AND ALLOW THE SALT-WATER SOLUTION TO COME INTO CONTACT WITH THE UNUSED POWER SEAT HARNESS CONNECTOR.
ON CERTAIN PASSENGER VEHICLES, THE RIGHT SIDE LOWER SEAT BELT ANCHOR MAY SEPARATE DURING A SEVERE VEHICLE CRASH.
ON CERTAIN PASSENGER VEHICLES, THE RIGHT SIDE LOWER SEAT BELT ANCHOR MAY SEPARATE DURING A SEVERE VEHICLE CRASH.
CERTAIN AIRTEX FUEL PUMP MODULE ASSEMBLIES, P/N E7081H, SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR THE VEHICLES LISTED ABOVE. THE WALL OF THE FLARED FITTING OF THE FUEL PUMP IS NOT THICK ENOUGH TO PREVENT THE MATING THREADED FITTINGS FROM BOTTOMING OUT BEFORE AN ADEQUATE SEAL IS ACHIEVED. THIS CONDITION MAY RESULT IN LEAKAGE OF FUEL AT THE CONNECTION OF THE VEHICLE FUEL LINE AND THE FUEL PUMP MODULE ASSEMBLY.
