Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
CERTAIN SPORT UTILITY VEHICLES AND TRUCKS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, TIRE SELECTION AND RIMS. THESE VEHICLES HAVE AN INCOMPLETE TIRE RIM DESIGNATION ON THE CERTIFICATION/TIRE LABEL LOCATED ON THE DRIVER'S DOOR EDGE. IN ADDITION, THE LABEL MAY ALSO BE MISSING THE TIRE LOAD RATING ON THE LABEL. ALTHOUGH THIS INFORMATION IS NOT REQUIRED BY THE STANDARD, IF A TIRE OF A LESSER LOAD RATING IS INSTALLED, THE TIRE MAY NOT BE ABLE TO SUSTAIN THE LOADS ENCOUNTERED DURING USE.
ON CERTAIN TRUCKS EQUIPPED WITH AN 8.1L V8 (RPO L8-VIN G) ENGINE HAVE A CONDITION IN WHICH THE ENGINE FUEL RAIL PULSE DAMPER RETAINER CLIP MAY FRACTURE RESULTING IN INADEQUATE RETENTION OF THE DAMPER.
ON CERTAIN TRUCKS EQUIPPED WITH AN 8.1L V8 (RPO L8-VIN G) ENGINE HAVE A CONDITION IN WHICH THE ENGINE FUEL RAIL PULSE DAMPER RETAINER CLIP MAY FRACTURE RESULTING IN INADEQUATE RETENTION OF THE DAMPER.
ON CERTAIN TRUCKS EQUIPPED WITH AN 8.1L V8 (RPO L8-VIN G) ENGINE HAVE A CONDITION IN WHICH THE ENGINE FUEL RAIL PULSE DAMPER RETAINER CLIP MAY FRACTURE RESULTING IN INADEQUATE RETENTION OF THE DAMPER.
ON CERTAIN TRUCKS EQUIPPED WITH AN 8.1L V8 (RPO L8-VIN G) ENGINE HAVE A CONDITION IN WHICH THE ENGINE FUEL RAIL PULSE DAMPER RETAINER CLIP MAY FRACTURE RESULTING IN INADEQUATE RETENTION OF THE DAMPER.
ON CERTAIN TRUCKS EQUIPPED WITH AN 8.1L V8 (RPO L8-VIN G) ENGINE HAVE A CONDITION IN WHICH THE ENGINE FUEL RAIL PULSE DAMPER RETAINER CLIP MAY FRACTURE RESULTING IN INADEQUATE RETENTION OF THE DAMPER.
ON CERTAIN TRUCKS EQUIPPED WITH AN 8.1L V8 (RPO L8-VIN G) ENGINE HAVE A CONDITION IN WHICH THE ENGINE FUEL RAIL PULSE DAMPER RETAINER CLIP MAY FRACTURE RESULTING IN INADEQUATE RETENTION OF THE DAMPER.
ON CERTAIN TRUCKS EQUIPPED WITH AN 8.1L V8 (RPO L8-VIN G) ENGINE HAVE A CONDITION IN WHICH THE ENGINE FUEL RAIL PULSE DAMPER RETAINER CLIP MAY FRACTURE RESULTING IN INADEQUATE RETENTION OF THE DAMPER.
CERTAIN MEDIUM DUTY TRUCKS EQUIPPED SR-7 BENDIX BRAKE VALVES, THE CHECK VALVE INSIDE THE VALVE CAVITY MAY NOT PROPERLY SET, CAUSING INTERNAL AIR LEAKAGE. IF THE CHECK VALVE DOES NOT PROPERLY SEAT, THE RESULTING LEAKAGE CAN CAUSE A DELAY IN THE APPLICATION OF THE SPRING BRAKES TO PARK THE VEHICLE AFTER OPERATOR PULLS THE DASH VALVE BUTTON.
CERTAIN MEDIUM DUTY TRUCKS EQUIPPED SR-7 BENDIX BRAKE VALVES, THE CHECK VALVE INSIDE THE VALVE CAVITY MAY NOT PROPERLY SET, CAUSING INTERNAL AIR LEAKAGE. IF THE CHECK VALVE DOES NOT PROPERLY SEAT, THE RESULTING LEAKAGE CAN CAUSE A DELAY IN THE APPLICATION OF THE SPRING BRAKES TO PARK THE VEHICLE AFTER OPERATOR PULLS THE DASH VALVE BUTTON.
CERTAIN MEDIUM DUTY TRUCKS EQUIPPED SR-7 BENDIX BRAKE VALVES, THE CHECK VALVE INSIDE THE VALVE CAVITY MAY NOT PROPERLY SET, CAUSING INTERNAL AIR LEAKAGE. IF THE CHECK VALVE DOES NOT PROPERLY SEAT, THE RESULTING LEAKAGE CAN CAUSE A DELAY IN THE APPLICATION OF THE SPRING BRAKES TO PARK THE VEHICLE AFTER OPERATOR PULLS THE DASH VALVE BUTTON.
CERTAIN FEDERAL-MOGUL NATIONAL AND CARQUEST AFTERMARKET HUB ASSEMBLIES, P/N 515058, SOLD FOR USE ON 2001-2006 GENERAL MOTORS 1500 AND 2500 4WD TRUCKS. ON THE SUBJECT HUB ASSEMBLIES, THE ABS SENSOR CORD DEPARTS FROM THE HUB ASSEMBLY AT A 90 DEGREE ANGLE. AS A RESULT, THERE IS A FIT ISSUE WITH THE BRAKE ROTOR DUST SHIELD INTERFERING WITH THE ABS SENSOR CORD. IF THE HUB ASSEMBLY IS INSTALLED DESPITE THIS INTERFERENCE, THE GAP BETWEEN THE ABS SENSOR AND THE TONE WHEEL MAY BE ALTERED. THIS MAY WEAKEN THE OUTPUT OF THE ABS SENSOR. DIMINISHED OUTPUT COULD RESULT IN AN UNWANTED ABS ACTIVATION AT LOW SPEEDS AND STOPPING DISTANCE COULD BE AFFECTED.
CERTAIN FEDERAL-MOGUL NATIONAL AND CARQUEST AFTERMARKET HUB ASSEMBLIES, P/N 515058, SOLD FOR USE ON 2001-2006 GENERAL MOTORS 1500 AND 2500 4WD TRUCKS. ON THE SUBJECT HUB ASSEMBLIES, THE ABS SENSOR CORD DEPARTS FROM THE HUB ASSEMBLY AT A 90 DEGREE ANGLE. AS A RESULT, THERE IS A FIT ISSUE WITH THE BRAKE ROTOR DUST SHIELD INTERFERING WITH THE ABS SENSOR CORD. IF THE HUB ASSEMBLY IS INSTALLED DESPITE THIS INTERFERENCE, THE GAP BETWEEN THE ABS SENSOR AND THE TONE WHEEL MAY BE ALTERED. THIS MAY WEAKEN THE OUTPUT OF THE ABS SENSOR. DIMINISHED OUTPUT COULD RESULT IN AN UNWANTED ABS ACTIVATION AT LOW SPEEDS AND STOPPING DISTANCE COULD BE AFFECTED.
CERTAIN FEDERAL-MOGUL NATIONAL AND CARQUEST AFTERMARKET HUB ASSEMBLIES, P/N 515058, SOLD FOR USE ON 2001-2006 GENERAL MOTORS 1500 AND 2500 4WD TRUCKS. ON THE SUBJECT HUB ASSEMBLIES, THE ABS SENSOR CORD DEPARTS FROM THE HUB ASSEMBLY AT A 90 DEGREE ANGLE. AS A RESULT, THERE IS A FIT ISSUE WITH THE BRAKE ROTOR DUST SHIELD INTERFERING WITH THE ABS SENSOR CORD. IF THE HUB ASSEMBLY IS INSTALLED DESPITE THIS INTERFERENCE, THE GAP BETWEEN THE ABS SENSOR AND THE TONE WHEEL MAY BE ALTERED. THIS MAY WEAKEN THE OUTPUT OF THE ABS SENSOR. DIMINISHED OUTPUT COULD RESULT IN AN UNWANTED ABS ACTIVATION AT LOW SPEEDS AND STOPPING DISTANCE COULD BE AFFECTED.
CERTAIN FEDERAL-MOGUL NATIONAL AND CARQUEST AFTERMARKET HUB ASSEMBLIES, P/N 515058, SOLD FOR USE ON 2001-2006 GENERAL MOTORS 1500 AND 2500 4WD TRUCKS. ON THE SUBJECT HUB ASSEMBLIES, THE ABS SENSOR CORD DEPARTS FROM THE HUB ASSEMBLY AT A 90 DEGREE ANGLE. AS A RESULT, THERE IS A FIT ISSUE WITH THE BRAKE ROTOR DUST SHIELD INTERFERING WITH THE ABS SENSOR CORD. IF THE HUB ASSEMBLY IS INSTALLED DESPITE THIS INTERFERENCE, THE GAP BETWEEN THE ABS SENSOR AND THE TONE WHEEL MAY BE ALTERED. THIS MAY WEAKEN THE OUTPUT OF THE ABS SENSOR. DIMINISHED OUTPUT COULD RESULT IN AN UNWANTED ABS ACTIVATION AT LOW SPEEDS AND STOPPING DISTANCE COULD BE AFFECTED.
CERTAIN FEDERAL-MOGUL NATIONAL AND CARQUEST AFTERMARKET HUB ASSEMBLIES, P/N 515058, SOLD FOR USE ON 2001-2006 GENERAL MOTORS 1500 AND 2500 4WD TRUCKS. ON THE SUBJECT HUB ASSEMBLIES, THE ABS SENSOR CORD DEPARTS FROM THE HUB ASSEMBLY AT A 90 DEGREE ANGLE. AS A RESULT, THERE IS A FIT ISSUE WITH THE BRAKE ROTOR DUST SHIELD INTERFERING WITH THE ABS SENSOR CORD. IF THE HUB ASSEMBLY IS INSTALLED DESPITE THIS INTERFERENCE, THE GAP BETWEEN THE ABS SENSOR AND THE TONE WHEEL MAY BE ALTERED. THIS MAY WEAKEN THE OUTPUT OF THE ABS SENSOR. DIMINISHED OUTPUT COULD RESULT IN AN UNWANTED ABS ACTIVATION AT LOW SPEEDS AND STOPPING DISTANCE COULD BE AFFECTED.
CERTAIN FEDERAL-MOGUL NATIONAL AND CARQUEST AFTERMARKET HUB ASSEMBLIES, P/N 515058, SOLD FOR USE ON 2001-2006 GENERAL MOTORS 1500 AND 2500 4WD TRUCKS. ON THE SUBJECT HUB ASSEMBLIES, THE ABS SENSOR CORD DEPARTS FROM THE HUB ASSEMBLY AT A 90 DEGREE ANGLE. AS A RESULT, THERE IS A FIT ISSUE WITH THE BRAKE ROTOR DUST SHIELD INTERFERING WITH THE ABS SENSOR CORD. IF THE HUB ASSEMBLY IS INSTALLED DESPITE THIS INTERFERENCE, THE GAP BETWEEN THE ABS SENSOR AND THE TONE WHEEL MAY BE ALTERED. THIS MAY WEAKEN THE OUTPUT OF THE ABS SENSOR. DIMINISHED OUTPUT COULD RESULT IN AN UNWANTED ABS ACTIVATION AT LOW SPEEDS AND STOPPING DISTANCE COULD BE AFFECTED.
CERTAIN FEDERAL-MOGUL NATIONAL AND CARQUEST AFTERMARKET HUB ASSEMBLIES, P/N 515058, SOLD FOR USE ON 2001-2006 GENERAL MOTORS 1500 AND 2500 4WD TRUCKS. ON THE SUBJECT HUB ASSEMBLIES, THE ABS SENSOR CORD DEPARTS FROM THE HUB ASSEMBLY AT A 90 DEGREE ANGLE. AS A RESULT, THERE IS A FIT ISSUE WITH THE BRAKE ROTOR DUST SHIELD INTERFERING WITH THE ABS SENSOR CORD. IF THE HUB ASSEMBLY IS INSTALLED DESPITE THIS INTERFERENCE, THE GAP BETWEEN THE ABS SENSOR AND THE TONE WHEEL MAY BE ALTERED. THIS MAY WEAKEN THE OUTPUT OF THE ABS SENSOR. DIMINISHED OUTPUT COULD RESULT IN AN UNWANTED ABS ACTIVATION AT LOW SPEEDS AND STOPPING DISTANCE COULD BE AFFECTED.
CERTAIN FEDERAL-MOGUL NATIONAL AND CARQUEST AFTERMARKET HUB ASSEMBLIES, P/N 515058, SOLD FOR USE ON 2001-2006 GENERAL MOTORS 1500 AND 2500 4WD TRUCKS. ON THE SUBJECT HUB ASSEMBLIES, THE ABS SENSOR CORD DEPARTS FROM THE HUB ASSEMBLY AT A 90 DEGREE ANGLE. AS A RESULT, THERE IS A FIT ISSUE WITH THE BRAKE ROTOR DUST SHIELD INTERFERING WITH THE ABS SENSOR CORD. IF THE HUB ASSEMBLY IS INSTALLED DESPITE THIS INTERFERENCE, THE GAP BETWEEN THE ABS SENSOR AND THE TONE WHEEL MAY BE ALTERED. THIS MAY WEAKEN THE OUTPUT OF THE ABS SENSOR. DIMINISHED OUTPUT COULD RESULT IN AN UNWANTED ABS ACTIVATION AT LOW SPEEDS AND STOPPING DISTANCE COULD BE AFFECTED.
CERTAIN FEDERAL-MOGUL NATIONAL AND CARQUEST AFTERMARKET HUB ASSEMBLIES, P/N 515058, SOLD FOR USE ON 2001-2006 GENERAL MOTORS 1500 AND 2500 4WD TRUCKS. ON THE SUBJECT HUB ASSEMBLIES, THE ABS SENSOR CORD DEPARTS FROM THE HUB ASSEMBLY AT A 90 DEGREE ANGLE. AS A RESULT, THERE IS A FIT ISSUE WITH THE BRAKE ROTOR DUST SHIELD INTERFERING WITH THE ABS SENSOR CORD. IF THE HUB ASSEMBLY IS INSTALLED DESPITE THIS INTERFERENCE, THE GAP BETWEEN THE ABS SENSOR AND THE TONE WHEEL MAY BE ALTERED. THIS MAY WEAKEN THE OUTPUT OF THE ABS SENSOR. DIMINISHED OUTPUT COULD RESULT IN AN UNWANTED ABS ACTIVATION AT LOW SPEEDS AND STOPPING DISTANCE COULD BE AFFECTED.
CERTAIN FEDERAL-MOGUL NATIONAL AND CARQUEST AFTERMARKET HUB ASSEMBLIES, P/N 515058, SOLD FOR USE ON 2001-2006 GENERAL MOTORS 1500 AND 2500 4WD TRUCKS. ON THE SUBJECT HUB ASSEMBLIES, THE ABS SENSOR CORD DEPARTS FROM THE HUB ASSEMBLY AT A 90 DEGREE ANGLE. AS A RESULT, THERE IS A FIT ISSUE WITH THE BRAKE ROTOR DUST SHIELD INTERFERING WITH THE ABS SENSOR CORD. IF THE HUB ASSEMBLY IS INSTALLED DESPITE THIS INTERFERENCE, THE GAP BETWEEN THE ABS SENSOR AND THE TONE WHEEL MAY BE ALTERED. THIS MAY WEAKEN THE OUTPUT OF THE ABS SENSOR. DIMINISHED OUTPUT COULD RESULT IN AN UNWANTED ABS ACTIVATION AT LOW SPEEDS AND STOPPING DISTANCE COULD BE AFFECTED.
CERTAIN FEDERAL-MOGUL NATIONAL AND CARQUEST AFTERMARKET HUB ASSEMBLIES, P/N 515058, SOLD FOR USE ON 2001-2006 GENERAL MOTORS 1500 AND 2500 4WD TRUCKS. ON THE SUBJECT HUB ASSEMBLIES, THE ABS SENSOR CORD DEPARTS FROM THE HUB ASSEMBLY AT A 90 DEGREE ANGLE. AS A RESULT, THERE IS A FIT ISSUE WITH THE BRAKE ROTOR DUST SHIELD INTERFERING WITH THE ABS SENSOR CORD. IF THE HUB ASSEMBLY IS INSTALLED DESPITE THIS INTERFERENCE, THE GAP BETWEEN THE ABS SENSOR AND THE TONE WHEEL MAY BE ALTERED. THIS MAY WEAKEN THE OUTPUT OF THE ABS SENSOR. DIMINISHED OUTPUT COULD RESULT IN AN UNWANTED ABS ACTIVATION AT LOW SPEEDS AND STOPPING DISTANCE COULD BE AFFECTED.
CERTAIN FEDERAL-MOGUL NATIONAL AND CARQUEST AFTERMARKET HUB ASSEMBLIES, P/N 515058, SOLD FOR USE ON 2001-2006 GENERAL MOTORS 1500 AND 2500 4WD TRUCKS. ON THE SUBJECT HUB ASSEMBLIES, THE ABS SENSOR CORD DEPARTS FROM THE HUB ASSEMBLY AT A 90 DEGREE ANGLE. AS A RESULT, THERE IS A FIT ISSUE WITH THE BRAKE ROTOR DUST SHIELD INTERFERING WITH THE ABS SENSOR CORD. IF THE HUB ASSEMBLY IS INSTALLED DESPITE THIS INTERFERENCE, THE GAP BETWEEN THE ABS SENSOR AND THE TONE WHEEL MAY BE ALTERED. THIS MAY WEAKEN THE OUTPUT OF THE ABS SENSOR. DIMINISHED OUTPUT COULD RESULT IN AN UNWANTED ABS ACTIVATION AT LOW SPEEDS AND STOPPING DISTANCE COULD BE AFFECTED.
CERTAIN CK MOTORSPORTS COMBINATION HEADLIGHTS, CLEAR CORNER, BUMPER, AND SIDE MARKER LIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON THE PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
CERTAIN CK MOTORSPORTS COMBINATION HEADLIGHTS, CLEAR CORNER, BUMPER, AND SIDE MARKER LIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON THE PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
CERTAIN CK MOTORSPORTS COMBINATION HEADLIGHTS, CLEAR CORNER, BUMPER, AND SIDE MARKER LIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON THE PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
CERTAIN CK MOTORSPORTS COMBINATION HEADLIGHTS, CLEAR CORNER, BUMPER, AND SIDE MARKER LIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON THE PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
CERTAIN CK MOTORSPORTS COMBINATION HEADLIGHTS, CLEAR CORNER, BUMPER, AND SIDE MARKER LIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON THE PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
CERTAIN CK MOTORSPORTS COMBINATION HEADLIGHTS, CLEAR CORNER, BUMPER, AND SIDE MARKER LIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON THE PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
CERTAIN CK MOTORSPORTS COMBINATION HEADLIGHTS, CLEAR CORNER, BUMPER, AND SIDE MARKER LIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON THE PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
