Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
THE INVOLVED VEHICLES WERE ASSEMBLED WITH IMPROPERLY MANUFACTURED STEERING ARM KNUCKLES. SHOULD AN IMPROPERLY MANUFACTURED STEERING ARM KNUCKLE FRACTURE AND SEPARATE, THE STEERING LINKAGE TIE ROD MAY DISENGAGE FROM THE KNUCKLE.
THE INVOLVED VEHICLES WERE ASSEMBLED WITH IMPROPERLY MANUFACTURED STEERING ARM KNUCKLES. SHOULD AN IMPROPERLY MANUFACTURED STEERING ARM KNUCKLE FRACTURE AND SEPARATE, THE STEERING LINKAGE TIE ROD MAY DISENGAGE FROM THE KNUCKLE.
THE INVOLVED VEHICLES WERE ASSEMBLED WITH IMPROPERLY MANUFACTURED STEERING ARM KNUCKLES. SHOULD AN IMPROPERLY MANUFACTURED STEERING ARM KNUCKLE FRACTURE AND SEPARATE, THE STEERING LINKAGE TIE ROD MAY DISENGAGE FROM THE KNUCKLE.
THE INVOLVED VEHICLES WERE MANUFACTURED WITHOUT A FUEL TANK SHIELD AT THE FRONT RIGHT CORNER OF THE MIDSHIP FUEL TANK. AS A RESULT, THE VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 301, FUEL SYSTEM INTEGRITY. IN THE EVENT OF A VEHICLE ACCIDENT, EXCESSIVE FUEL SPILLAGE COULD RESULT.
THE INVOLVED VEHICLES WERE MANUFACTURED WITHOUT A FUEL TANK SHIELD AT THE FRONT RIGHT CORNER OF THE MIDSHIP FUEL TANK. AS A RESULT, THE VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 301, FUEL SYSTEM INTEGRITY. IN THE EVENT OF A VEHICLE ACCIDENT, EXCESSIVE FUEL SPILLAGE COULD RESULT.
THE INVOLVED VEHICLES WERE MANUFACTURED WITHOUT A FUEL TANK SHIELD AT THE FRONT RIGHT CORNER OF THE MIDSHIP FUEL TANK. AS A RESULT, THE VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 301, FUEL SYSTEM INTEGRITY. IN THE EVENT OF A VEHICLE ACCIDENT, EXCESSIVE FUEL SPILLAGE COULD RESULT.
THE INVOLVED VEHICLES WERE BUILT WITH SAFETY COMPLIANCE CERTIFICATION LABELS THAT CONTAINED INCORRECT GVWR AND GAWR WEIGHT INFORMATION. THE GVWRS COULD BE OVERSTATED BY UP TO 197 LBS., DUE TO AN ERROR IN THE REPORTING OF INCREMENTAL OPTION WEIGHTS USED TO DERIVE THE GVWRS AND GAWRS.
THE WORD LIGHTS WAS OMITTED FROM THE PANEL APPLIQUE IDENTIFYING THE HEADLAMP SWITCH. WITHOUT THIS IDENTIFICATION THE INVOLVED VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 101, CONTROLS AND DISPLAYS.
THE INVOLVED VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 212, WINDSHIELD MOUNTING, IN THAT SOME OF THE VEHICLES WERE BUILT WITHOUT THE SPECIFIED WINDSHIELD WEATHERSTRIP RETAINING COMPONENTS.
THE INVOLVED VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 212, WINDSHIELD MOUNTING, IN THAT SOME OF THE VEHICLES WERE BUILT WITHOUT THE SPECIFIED WINDSHIELD WEATHERSTRIP RETAINING COMPONENTS.
THE INVOLVED VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 212, WINDSHIELD MOUNTING, IN THAT SOME OF THE VEHICLES WERE BUILT WITHOUT THE SPECIFIED WINDSHIELD WEATHERSTRIP RETAINING COMPONENTS.
SOME OF THE INVOLVED VEHICLES DO NOT HAVE THE HAIR PIN CLIP USED TO RETAIN THE PUSHROD TO THE BRAKE PEDAL PUSHROD PIN INSTALLED. IF THIS CLIP IS MISSING, THE PUSHROD MAY BECOME DISENGAGED FROM THE BRAKE PEDAL PUSHROD PIN.
THE INVOLVED VEHICLES MAY HAVE BEEN BUILT WITH INCORRECT WELD NUTS THAT ATTACH THE REAR PORTION OF THE FRONT OUTBOARD SEAT TRACK TO THE FLOOR PAN. THE INCORRECT NUTS HAVE AN OVERSIZE DIAMETER AND THREAD, AND UPON FRONT SEAT TRACK ANCHOR BOLT INSTALLATION, THE THREADS MAY HAVE BEEN STRIPPED.
THE INVOLVED VEHICLES MAY HAVE BEEN BUILT WITH INCORRECT WELD NUTS THAT ATTACH THE REAR PORTION OF THE FRONT OUTBOARD SEAT TRACK TO THE FLOOR PAN. THE INCORRECT NUTS HAVE AN OVERSIZE DIAMETER AND THREAD, AND UPON FRONT SEAT TRACK ANCHOR BOLT INSTALLATION, THE THREADS MAY HAVE BEEN STRIPPED.
THE INVOLVED VEHICLES MAY HAVE BEEN BUILT WITH INCORRECT WELD NUTS THAT ATTACH THE REAR PORTION OF THE FRONT OUTBOARD SEAT TRACK TO THE FLOOR PAN. THE INCORRECT NUTS HAVE AN OVERSIZE DIAMETER AND THREAD, AND UPON FRONT SEAT TRACK ANCHOR BOLT INSTALLATION, THE THREADS MAY HAVE BEEN STRIPPED.
THE STEERING GEARS ON THE INVOLVED VEHICLES MAY HAVE BEEN BUILT WITH IMPROPERLY MANUFACTURED SECTOR SHAFTS FROM WHICH THE THREADED PORTIONS OF THE SHAFTS MAY FRACTURE AND SEPARATE. SHOULD THE SECTOR SHAFT FRACTURE, THE PITMAN ARM MAY DISENGAGE FROM THE SPLINED PORTION OF THE SECTOR SHAFT.
THE STEERING GEARS ON THE INVOLVED VEHICLES MAY HAVE BEEN BUILT WITH IMPROPERLY MANUFACTURED SECTOR SHAFTS FROM WHICH THE THREADED PORTIONS OF THE SHAFTS MAY FRACTURE AND SEPARATE. SHOULD THE SECTOR SHAFT FRACTURE, THE PITMAN ARM MAY DISENGAGE FROM THE SPLINED PORTION OF THE SECTOR SHAFT.
THE STEERING GEARS ON THE INVOLVED VEHICLES MAY HAVE BEEN BUILT WITH IMPROPERLY MANUFACTURED SECTOR SHAFTS FROM WHICH THE THREADED PORTIONS OF THE SHAFTS MAY FRACTURE AND SEPARATE. SHOULD THE SECTOR SHAFT FRACTURE, THE PITMAN ARM MAY DISENGAGE FROM THE SPLINED PORTION OF THE SECTOR SHAFT.
THE STEERING GEARS ON THE INVOLVED VEHICLES MAY HAVE BEEN BUILT WITH IMPROPERLY MANUFACTURED SECTOR SHAFTS FROM WHICH THE THREADED PORTIONS OF THE SHAFTS MAY FRACTURE AND SEPARATE. SHOULD THE SECTOR SHAFT FRACTURE, THE PITMAN ARM MAY DISENGAGE FROM THE SPLINED PORTION OF THE SECTOR SHAFT.
THE STEERING GEARS ON THE INVOLVED VEHICLES MAY HAVE BEEN BUILT WITH IMPROPERLY MANUFACTURED SECTOR SHAFTS FROM WHICH THE THREADED PORTIONS OF THE SHAFTS MAY FRACTURE AND SEPARATE. SHOULD THE SECTOR SHAFT FRACTURE, THE PITMAN ARM MAY DISENGAGE FROM THE SPLINED PORTION OF THE SECTOR SHAFT.
THE FLUID RETURN HOSE INSTALLED BETWEEN THE POWER STEERING RESERVOIR AND PUMP IS SUSCEPTIBLE TO DETERIORATION AND KINKING. DETERIORATION OF THE HOSE PERMITS PARTICLES TO ENTER THE POWER STEERING FLUID SYSTEM RESTRICTING FLOW. BOTH HOSE DETERIORATION AND KINKING MAY RESULT IN LOSS OF POWER STEERING ASSIST AND INCREASED MANUAL STEERING EFFORTS.
THE INVOLVED VEHICLES WERE EQUIPPED WITH AUTOMATIC TRANSMISSIONS IN WHICH THE PARKING PAWL WAS NOT HEAT-TREATED. DURING NORMAL VEHICLE OPERATION, A PARKING PAWL THAT HAS NOT BEEN HEAT-TREATED COULD BECOME DEFORMED OR WORN TO THE POINT THAT THE TRANSMISSION WILL NOT LOCK IN PARK. AS A RESULT, THE VEHICLE COULD ROLL FREE IF THE DRIVER DOES NOT SET THE PARKING BRAKE WHEN PARKING OR LEAVING VEHICLE UNATTENDED.
THE INVOLVED VEHICLES WERE EQUIPPED WITH AUTOMATIC TRANSMISSIONS IN WHICH THE PARKING PAWL WAS NOT HEAT-TREATED. DURING NORMAL VEHICLE OPERATION, A PARKING PAWL THAT HAS NOT BEEN HEAT-TREATED COULD BECOME DEFORMED OR WORN TO THE POINT THAT THE TRANSMISSION WILL NOT LOCK IN PARK. AS A RESULT, THE VEHICLE COULD ROLL FREE IF THE DRIVER DOES NOT SET THE PARKING BRAKE WHEN PARKING OR LEAVING VEHICLE UNATTENDED.
THE INVOLVED VEHICLES WERE EQUIPPED WITH AUTOMATIC TRANSMISSIONS IN WHICH THE PARKING PAWL WAS NOT HEAT-TREATED. DURING NORMAL VEHICLE OPERATION, A PARKING PAWL THAT HAS NOT BEEN HEAT-TREATED COULD BECOME DEFORMED OR WORN TO THE POINT THAT THE TRANSMISSION WILL NOT LOCK IN PARK. AS A RESULT, THE VEHICLE COULD ROLL FREE IF THE DRIVER DOES NOT SET THE PARKING BRAKE WHEN PARKING OR LEAVING VEHICLE UNATTENDED.
THE INVOLVED VEHICLES WERE EQUIPPED WITH AUTOMATIC TRANSMISSIONS IN WHICH THE PARKING PAWL WAS NOT HEAT-TREATED. DURING NORMAL VEHICLE OPERATION, A PARKING PAWL THAT HAS NOT BEEN HEAT-TREATED COULD BECOME DEFORMED OR WORN TO THE POINT THAT THE TRANSMISSION WILL NOT LOCK IN PARK. AS A RESULT, THE VEHICLE COULD ROLL FREE IF THE DRIVER DOES NOT SET THE PARKING BRAKE WHEN PARKING OR LEAVING VEHICLE UNATTENDED.
THE INVOLVED VEHICLES WERE EQUIPPED WITH AUTOMATIC TRANSMISSIONS IN WHICH THE PARKING PAWL WAS NOT HEAT-TREATED. DURING NORMAL VEHICLE OPERATION, A PARKING PAWL THAT HAS NOT BEEN HEAT-TREATED COULD BECOME DEFORMED OR WORN TO THE POINT THAT THE TRANSMISSION WILL NOT LOCK IN PARK. AS A RESULT, THE VEHICLE COULD ROLL FREE IF THE DRIVER DOES NOT SET THE PARKING BRAKE WHEN PARKING OR LEAVING VEHICLE UNATTENDED.
THE INVOLVED VEHICLES WERE EQUIPPED WITH AUTOMATIC TRANSMISSIONS IN WHICH THE PARKING PAWL WAS NOT HEAT-TREATED. DURING NORMAL VEHICLE OPERATION, A PARKING PAWL THAT HAS NOT BEEN HEAT-TREATED COULD BECOME DEFORMED OR WORN TO THE POINT THAT THE TRANSMISSION WILL NOT LOCK IN PARK. AS A RESULT, THE VEHICLE COULD ROLL FREE IF THE DRIVER DOES NOT SET THE PARKING BRAKE WHEN PARKING OR LEAVING VEHICLE UNATTENDED.
THE INVOLVED VEHICLES WERE EQUIPPED WITH AUTOMATIC TRANSMISSIONS IN WHICH THE PARKING PAWL WAS NOT HEAT-TREATED. DURING NORMAL VEHICLE OPERATION, A PARKING PAWL THAT HAS NOT BEEN HEAT-TREATED COULD BECOME DEFORMED OR WORN TO THE POINT THAT THE TRANSMISSION WILL NOT LOCK IN PARK. AS A RESULT, THE VEHICLE COULD ROLL FREE IF THE DRIVER DOES NOT SET THE PARKING BRAKE WHEN PARKING OR LEAVING VEHICLE UNATTENDED.
DUE TO AN ERROR IN THE VEHICLE ASSEMBLY COMPUTER BROADCAST PROGRAM, THE INVOLVED VEHICLES WERE EQUIPPED WITH 14X5.5 INCH WHEEL RIMS WHICH WERE INTENDED FOR USE ON PASSENGER CARS. THE TIRES WERE NOT MARKED WITH THE INFORMATION SPECIFIED BY FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 120, TIRE SELECTION AND RIMS FOR MOTOR VEHICLES OTHER THAN PASSENGER CARS. AS A RESULT, A NON-COMPLIANCE EXISTS TO THIS STANDARD.
THE ENGINE COOLING FAN BLADES MAY CRACK UNDER HIGH SPEED OPERATING CONDITIONS. FRAGMENTS MAY SEPARATE AND DAMAGE THE ENGINE COMPONENTS, AND IF THE HOOD IS OPEN AND THE ENGINE IS RUNNING, BLADE FRAGMENTS COULD FLY OUT FROM THE VEHICLE AND INJURE NEARBY PERSONS.
