Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
ON CERTAIN VEHICLES, THE RIGHT AND LEFT HAND REAR BRAKE BACKING PLATE ATTACHMENT BOLTS MAY NOT HAVE BEEN TIGHTENED TO THE CORRECT SPECIFICATIONS. BACKING PLATE BOLTS MAY NOT BE ABLE TO WITHSTAND THE LOADS EXPERIENCED DURING TRUCK SHIPMENT. IF THE BOLTS LOOSEN FROM THE SPINDLE DURING OPERATION, BACKING PLATE MOVEMENT MAY RESULT IN WEAKENING OR PREMATURE WEAR OF ONE OR BOTH REAR BRAKE TUBES. THIS COULD LEAD TO LOSS OF BRAKE FLUID.
THE INVOLVED VEHICLES MAY START IN REVERSE GEAR. THIS DOES NOT COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 102, TRANSMISSION SHIFT LEVER SEQUENCE, STARTER INTERLOCK, AND TRANSMISSION BRAKING AFFECT. SOME OF THESE VEHICLES MAY BE EQUIPPED WITH A DEFECTIVE NEUTRAL START SWITCH THAT OCCASIONALLY PERMITS ENGINE STARTING WITH THE TRANSMISSION SHIFT LEVER IN THE REVERSE (R) POSITION.
CERTAIN VEHICLES WERE EQUIPPED WITH FRONT BRAKE HOSE ASSEMBLIES THAT WERE INCORRECTLY MANUFACTURED BY THE SUPPLIER. THESE ASSEMBLIES, BOTH RH AND LH, WERE INCORRECTLY BUILT WITH THE FITTINGS MISORIENTED BY 90 DEGREES. THIS COULD CAUSE CHAFING OF THE BRAKE HOSE THROUGH CONTACT WITH THE ADJACENT TIRE DURING FULL TURNS. CONTINUED CHAFING COULD RESULT IN A BRAKE FLUID LEAK.
CERTAIN VEHICLES WERE EQUIPPED WITH FRONT BRAKE HOSE ASSEMBLIES THAT WERE INCORRECTLY MANUFACTURED BY THE SUPPLIER. THESE ASSEMBLIES, BOTH RH AND LH, WERE INCORRECTLY BUILT WITH THE FITTINGS MISORIENTED BY 90 DEGREES. THIS COULD CAUSE CHAFING OF THE BRAKE HOSE THROUGH CONTACT WITH THE ADJACENT TIRE DURING FULL TURNS. CONTINUED CHAFING COULD RESULT IN A BRAKE FLUID LEAK.
CERTAIN VEHICLES WERE EQUIPPED WITH FRONT BRAKE HOSE ASSEMBLIES THAT WERE INCORRECTLY MANUFACTURED BY THE SUPPLIER. THESE ASSEMBLIES, BOTH RH AND LH, WERE INCORRECTLY BUILT WITH THE FITTINGS MISORIENTED BY 90 DEGREES. THIS COULD CAUSE CHAFING OF THE BRAKE HOSE THROUGH CONTACT WITH THE ADJACENT TIRE DURING FULL TURNS. CONTINUED CHAFING COULD RESULT IN A BRAKE FLUID LEAK.
CERTAIN VEHICLES WERE EQUIPPED WITH FRONT BRAKE HOSE ASSEMBLIES THAT WERE INCORRECTLY MANUFACTURED BY THE SUPPLIER. THESE ASSEMBLIES, BOTH RH AND LH, WERE INCORRECTLY BUILT WITH THE FITTINGS MISORIENTED BY 90 DEGREES. THIS COULD CAUSE CHAFING OF THE BRAKE HOSE THROUGH CONTACT WITH THE ADJACENT TIRE DURING FULL TURNS. CONTINUED CHAFING COULD RESULT IN A BRAKE FLUID LEAK.
THE INVOLVED VEHICLES WERE MANUFACTURED WITHOUT THE MIDSHIP FUEL TANK PROTECTIVE SHIELDS. AS A RESULT, THEY DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 301, FUEL SYSTEM INTEGRITY, DUE TO EXCESSIVE FUEL SPILLAGE UPON FRONTAL IMPACT.
THE INVOLVED VEHICLES WERE MANUFACTURED WITHOUT THE MIDSHIP FUEL TANK PROTECTIVE SHIELDS. AS A RESULT, THEY DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 301, FUEL SYSTEM INTEGRITY, DUE TO EXCESSIVE FUEL SPILLAGE UPON FRONTAL IMPACT.
THE INVOLVED VEHICLES WERE MANUFACTURED WITHOUT THE MIDSHIP FUEL TANK PROTECTIVE SHIELDS. AS A RESULT, THEY DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 301, FUEL SYSTEM INTEGRITY, DUE TO EXCESSIVE FUEL SPILLAGE UPON FRONTAL IMPACT.
THE INVOLVED VEHICLES WERE MANUFACTURED WITHOUT THE MIDSHIP FUEL TANK PROTECTIVE SHIELDS. AS A RESULT, THEY DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 301, FUEL SYSTEM INTEGRITY, DUE TO EXCESSIVE FUEL SPILLAGE UPON FRONTAL IMPACT.
SOME OF THE ENGINE COOLING FANS ON THE INVOLVED VEHICLES MAY BE SUBJECT TO HIGH BLADE STRESSES THAT CAN RESULT FROM RESONANT VIBRATION INPUTS OCCURRING DURING NORMAL VEHICLE OPERATION.
THE INVOLVED VEHICLES DO NOT HAVE A PROTECTIVE FUEL TANK SHIELD. AS A RESULT THE 137 INCH AND 161 INCH WHEELBASE CHASSIS CABS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 301, FUEL SYSTEM INTEGRITY. IF THE ABOVE VEHICLES UNDERGO FRONTAL IMPACT, THE DRIVE SHAFT FRONT UNIVERSAL JOINT MAY COME INTO CONTACT WITH THE FUEL TANK, RESULTING IN FUEL SPILLAGE.
THE INVOLVED CHASSIS CABS WERE IMPROPERLY EQUIPPED WITH OUTSIDE REARVIEW MIRRORS WITH A REFLECTIVE SURFACE AREA OF TWENTY SQUARE INCHES, WHICH DOES NOT COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 111, REARVIEW MIRRORS. THIS REQUIRES VEHICLES WITH A GVWR OF MORE THAT 10,000 LBS. TO BE EQUIPPED WITH OUTSIDE REARVIEW MIRRORS OF NOT LESS THAN FIFTY SQUARE INCHES OF REFLECTIVE SURFACE AREA.
DUE TO COMPUTER INPUT ERROR WHICH RESULTED IN AN INCORRECT BUILD SCHEDULE, SOME VEHICLES WERE SHIPPED WITHOUT THE REQUIRED EXHAUST SYSTEM HEAT SHIELDS. WHEN THE VEHICLE IS IDLED OVER AN EXTENDED PERIOD OF TIME, A MISSING EXHAUST HEAT SHIELD MAY RESULT IN DANGEROUSLY HIGH FLOOR PAN TEMPERATURES.
DUE TO COMPUTER INPUT ERROR WHICH RESULTED IN AN INCORRECT BUILD SCHEDULE, SOME VEHICLES WERE SHIPPED WITHOUT THE REQUIRED EXHAUST SYSTEM HEAT SHIELDS. WHEN THE VEHICLE IS IDLED OVER AN EXTENDED PERIOD OF TIME, A MISSING EXHAUST HEAT SHIELD MAY RESULT IN DANGEROUSLY HIGH FLOOR PAN TEMPERATURES.
DUE TO COMPUTER INPUT ERROR WHICH RESULTED IN AN INCORRECT BUILD SCHEDULE, SOME VEHICLES WERE SHIPPED WITHOUT THE REQUIRED EXHAUST SYSTEM HEAT SHIELDS. WHEN THE VEHICLE IS IDLED OVER AN EXTENDED PERIOD OF TIME, A MISSING EXHAUST HEAT SHIELD MAY RESULT IN DANGEROUSLY HIGH FLOOR PAN TEMPERATURES.
ON CERTAIN VEHICLES, TWO FUEL LINE BRACKETS WERE INCORRECTLY POSITIONED, ALLOWING THE FUEL LINE TO COME INTO CONTACT WITH THE LEFT HAND FRONT BRAKE JOUNCE HOSE. CONTACT WITH THE FUEL LINE, WHICH HAS A METAL OUTER SHIELD, COULD CAUSE CHAFING OF THE BRAKE HOSE.
CERTAIN VEHICLES WERE PRODUCED WITH WHEEL ASSEMBLIES THAT MAY HAVE CRACKS NEAR THE BOLT HOLES IN THE WHEEL DISC. DURING VEHICLE USE, THE CRACKS COULD GRADUALLY INCREASE AND RESULT IN PARTIAL OR COMPLETE SEPARATION OF THE WHEEL AND TIRE ASSEMBLY FROM THE VEHICLE.
CERTAIN VEHICLES WERE PRODUCED WITH WHEEL ASSEMBLIES THAT MAY HAVE CRACKS NEAR THE BOLT HOLES IN THE WHEEL DISC. DURING VEHICLE USE, THE CRACKS COULD GRADUALLY INCREASE AND RESULT IN PARTIAL OR COMPLETE SEPARATION OF THE WHEEL AND TIRE ASSEMBLY FROM THE VEHICLE.
CERTAIN VEHICLES WERE PRODUCED WITH WHEEL ASSEMBLIES THAT MAY HAVE CRACKS NEAR THE BOLT HOLES IN THE WHEEL DISC. DURING VEHICLE USE, THE CRACKS COULD GRADUALLY INCREASE AND RESULT IN PARTIAL OR COMPLETE SEPARATION OF THE WHEEL AND TIRE ASSEMBLY FROM THE VEHICLE.
CERTAIN VEHICLES WERE PRODUCED WITH WHEEL ASSEMBLIES THAT MAY HAVE CRACKS NEAR THE BOLT HOLES IN THE WHEEL DISC. DURING VEHICLE USE, THE CRACKS COULD GRADUALLY INCREASE AND RESULT IN PARTIAL OR COMPLETE SEPARATION OF THE WHEEL AND TIRE ASSEMBLY FROM THE VEHICLE.
MISBUILT WIRING HARNESSES MAY HAVE BEEN INSTALLED ON CERTAIN VEHICLES. THIS WOULD ALLOW THE POWER WINDOWS TO BE OPERATED WHILE THE IGNITION KEY IS TURNED OFF, A CONDITION WHICH FAILS TO COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 118, POWER OPERATED WINDOW SYSTEMS.
CERTAIN VEHICLES WERE NOT EQUIPPED WITH A FRONT PROTECTIVE SHIELD FOR THE MID-SHIP FUEL TANK. THESE VEHICLES DO NOT COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 301, FUEL SYSTEM INTEGRITY. IN THE EVENT OF A FRONTAL COLLISION, EXCESSIVE FUEL SPILLAGE MAY OCCUR.
CERTAIN VEHICLES WERE NOT EQUIPPED WITH A FRONT PROTECTIVE SHIELD FOR THE MID-SHIP FUEL TANK. THESE VEHICLES DO NOT COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 301, FUEL SYSTEM INTEGRITY. IN THE EVENT OF A FRONTAL COLLISION, EXCESSIVE FUEL SPILLAGE MAY OCCUR.
CERTAIN VEHICLES MAY HAVE BEEN ASSEMBLED WITHOUT THE SPECIFIED EXHAUST SYSTEM HEAT SHIELDS. THE ABSENCE OF THESE SHIELDS COULD CAUSE HIGH FLOOR PAN TEMPERATURES AND SMOLDERING OF THE FLOOR COVERINGS UNDER CERTAIN DRIVING OR ENGINE MALFUNCTION CONDITIONS.
ON CERTAIN VEHICLES, THE PINCH BOLT AND NUT USED TO ATTACH THE INTERMEDIATE STEERIING SHAFT TO THE STEERING COLUMN WERE OMITTED DURING ASSEMBLY. THIS COULD RESULT IN SEPARATION OF THE STEERING SHAFT FROM THE STEERING COLUMN.
WINDSHIELDS MAY HAVE BEEN INSTALLED ON THESE VEHICLES WITHOUT THE APPLICATION OF A BUTYL PRIMER ON THE MOUNTING SURFACE OF THE GLAZING. THE PRIMER IS REQUIRED TO ENSURE ADEQUATE RETENTION OF THE WINDSHIELD TO ITS OPENING FLANGE. THIS CONSTITUTES A NON-COMPLIANCE WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 212, WINDSHIELD MOUNTING.
WINDSHIELDS MAY HAVE BEEN INSTALLED ON THESE VEHICLES WITHOUT THE APPLICATION OF A BUTYL PRIMER ON THE MOUNTING SURFACE OF THE GLAZING. THE PRIMER IS REQUIRED TO ENSURE ADEQUATE RETENTION OF THE WINDSHIELD TO ITS OPENING FLANGE. THIS CONSTITUTES A NON-COMPLIANCE WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 212, WINDSHIELD MOUNTING.
THE PARKING PAWL ACTUATING ROD IN THE TRANSMISSION MAY HAVE AN INSUFFICIENT OR CRACKED WELD. THIS CAN CAUSE THE PARK CAM END TO SEPARATE FROM THE ROD ITSELF, PREVENTING THE PARKING PAWL FROM ENGAGING THE PARKING GEAR WHEN THE SELECTOR IS PLACED IN THE PARK POSITION.
THE PARKING PAWL ACTUATING ROD IN THE TRANSMISSION MAY HAVE AN INSUFFICIENT OR CRACKED WELD. THIS CAN CAUSE THE PARK CAM END TO SEPARATE FROM THE ROD ITSELF, PREVENTING THE PARKING PAWL FROM ENGAGING THE PARKING GEAR WHEN THE SELECTOR IS PLACED IN THE PARK POSITION.
