Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
THESE VEHICLES DO NOT MEET THE REAR IMPACT TEST REQUIREMENTS OF FMVSS 301, FUEL SYSTEM INTEGRITY.
THE FRONT SUSPENSION TRACK BAR HAS INADEQUATE FATIGUE STRENGTH.
SOME UPPER CONTROL ARM ATTACHING BOLTS CAN FAIL DUE TO IMPROPER HEAT TREATMENT. THE BOLTS ARE TOO SOFT TO WITHSTAND THE STRESSES IN THE STEERING SYSTEM AND CAN BREAK.
MOISTURE CAN GET INTO THE POWERTRAIN CONTROL MODULE (PCM) CAUSING DRIVEABILITY MALFUNCTIONS, INCLUDING STALLING.
THE REAR BRAKE HOSE MOUNTING BRACKET SCREWS CAN FAIL ALLOWING THE BRAKE HOSES TO MOVE OUT OF POSITION. THE UNRESTRAINED HOSES ARE THEN SUSCEPTIBLE TO DAMAGE WHICH COULD RESULT IN BRAKE FLUID LEAKAGE.
THE SAFETY BELT ANCHORS (BUCKLE LOCK BARS) DO NOT MEET THE STATIC LOAD REQUIREMENTS OF FMVSS NO. 210, SEAT BELT ASSEMBLY ANCHORAGES.
THE RIGHT STEERING TIE ROD CAN RUB THROUGH THE AUTOMATIC TRANSMISSION WIRING HARNESS CAUSING A SHORT CIRCUIT WHICH RESULTS IN ELECTRICAL SYSTEM MALFUNCTIONS INCLUDING ENGINE STALLING AND AN INOPERATIVE PARK/STARTER INTERLOCK SYSTEM.
TWO FUEL TANK SUPPORT STRAP ATTACHING STUDS WERE NOT ADEQUATELY TIGHTENED, WHICH COULD CAUSE ONE OR BOTH OF THE STRAP(S) TO SEPARATE, MISLOCATING THE FUEL TANKS OR ALLOW COMPLETE SEPARATION OF THE FUEL TANK FROM THE VEHICLE.
THE END CAP CONNECTING THE HEAT EXCHANGER'S CORE TO THE ENGINE COOLING SYSTEM COULD RUPTURE AND ALLOW HOT COOLANT TO ESCAPE INTO THE PASSENGER COMPARTMENT.
THE END CAP CONNECTING THE HEAT EXCHANGER'S CORE TO THE ENGINE COOLING SYSTEM COULD RUPTURE AND ALLOW HOT COOLANT TO ESCAPE INTO THE PASSENGER COMPARTMENT.
THE END CAP CONNECTING THE HEAT EXCHANGER'S CORE TO THE ENGINE COOLING SYSTEM COULD RUPTURE AND ALLOW HOT COOLANT TO ESCAPE INTO THE PASSENGER COMPARTMENT.
THE ABS BRAKE MASTER CYLINDER REAR SEAL ALLOWS AIR TO ENTER THE BRAKE SYSTEM, CAUSING SPONGY BRAKES OR PARTIAL BRAKE SYSTEM LOSS.
THE SEAT BACK LATCH LEVER PIVOT RIVETS ARE SUSCEPTIBLE TO DISTORTION. THE DISTORTED ASSEMBLIES ALLOW THE SEAT BACK RELEASE LATCH LEVER TO REMAIN IN THE RELEASED POSITION WHICH IS IN NON-COMPLIANCE WITH FMVSS NO. 207, SEATING SYSTEMS.
WHEELS WITH MISFORMED LUG NUT SEATS WERE INSTALLED ON THESE VEHICLES. THIS CAUSES REDUCED NUT TO WHEEL CONTACT AREA AND LIMITS THE WHEEL SELF-CENTERING CAPABILITY DURING INSTALLATION. THIS RESULTS IN LOSS OF WHEEL LUG NUT TORQUE RETENTION.
BOSCH DISTRIBUTOR-TYPE FUEL PUMPS HAVE A MANUFACTURING DEFECT THAT CAN CAUSE THE BALL PIN, WHICH IS PART OF THE PUMP'S CONTROL LEVER ASSEMBLY, TO BREAK CAUSING THE LINK BETWEEN THE CONTROL SLEEVE AND THE CONTROL LEVER TO BECOME INOPERATIVE.
BOSCH DISTRIBUTOR-TYPE FUEL PUMPS HAVE A MANUFACTURING DEFECT THAT CAN CAUSE THE BALL PIN, WHICH IS PART OF THE PUMP'S CONTROL LEVER ASSEMBLY, TO BREAK CAUSING THE LINK BETWEEN THE CONTROL SLEEVE AND THE CONTROL LEVER TO BECOME INOPERATIVE.
BOSCH DISTRIBUTOR-TYPE FUEL PUMPS HAVE A MANUFACTURING DEFECT THAT CAN CAUSE THE BALL PIN, WHICH IS PART OF THE PUMP'S CONTROL LEVER ASSEMBLY, TO BREAK CAUSING THE LINK BETWEEN THE CONTROL SLEEVE AND THE CONTROL LEVER TO BECOME INOPERATIVE.
FRONT SUSPENSION TRACK BAR ATTACHMENT TO THE AXLE MAY NOT BE ADEQUATELY TIGHTENED.
THE WELD ON THE RECEIVER UNIT OF THE TRAILER HITCH CAN BREAK.
THE WELD ON THE RECEIVER UNIT OF THE TRAILER HITCH CAN BREAK.
THE WELD ON THE RECEIVER UNIT OF THE TRAILER HITCH CAN BREAK.
THE WELD ON THE RECEIVER UNIT OF THE TRAILER HITCH CAN BREAK.
THE WELD ON THE RECEIVER UNIT OF THE TRAILER HITCH CAN BREAK.
THE WELDING ATTACHMENTS OF THE FRONT FRAME RAILS TO THE FLOOR PAN SHEET METAL MAY NOT BE PROPERLY WELDED.
THE WELDING ATTACHMENTS OF THE FRONT FRAME RAILS TO THE FLOOR PAN SHEET METAL MAY NOT BE PROPERLY WELDED.
THE 15 INCH WHEELS HAVE MALFORMED LUG NUT SEAT CONFIGURATION WHICH CAUSES POOR NUT-TO-WHEEL CONTACT AND CENTERING OF THE WHEEL DURING INSTALLATION.
SOME OF THE ABS EQUIPPED VEHICLES WERE BUILT WITH AN UNDERSIZED BRAKE RETURN CHECK VALVE. IN INCIDENTS WHERE HARD BRAKE PEDAL EFFORT IS APPLIED ON LOW FRICTION ROAD SURFACES, LIKE RAIN COVERED STREETS, THE VALVES MAY FAIL, CAUSING THE ABS TO BECOME INOPERATIVE. THIS CREATES EXCESS BRAKE PEDAL TRAVEL AND MAY CAUSE THE ABS WARNING LIGHT TO COME ON.
SOME OF THE ABS EQUIPPED VEHICLES WERE BUILT WITH AN UNDERSIZED BRAKE RETURN CHECK VALVE. IN INCIDENTS WHERE HARD BRAKE PEDAL EFFORT IS APPLIED ON LOW FRICTION ROAD SURFACES, LIKE RAIN COVERED STREETS, THE VALVES MAY FAIL, CAUSING THE ABS TO BECOME INOPERATIVE. THIS CREATES EXCESS BRAKE PEDAL TRAVEL AND MAY CAUSE THE ABS WARNING LIGHT TO COME ON.
A CONDITION EXISTS THAT ALLOWS OIL TO LEAK FROM THE ALL WHEEL DRIVE TRANSFER CASE. LOW OIL LEVELS IN THE TRANSFER CASE CAN CAUSE BEARING DAMAGE AND FAILURE.
FUEL TANK FLANGES WERE NOT BENT AS REQUIRED TO ALLOW THE SPECIFIED CLEARANCE FOR THE FUEL TANK MOUNTING STRAPS AND FUEL LINES AT THE TANK.
