Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
THE RIGHT HAND SPINDLE NUT WAS NOT PROPERLY TIGHTENED DURING ASSEMBLY. THIS CAN CAUSE PREMATURE WHEEL BEARING FAILURE AND OVER TIME, THE SPINDLE CAN FRACTURE.
WATER INTRUSION CAN CAUSE A SHORT CIRCUIT IN THE POWER DOOR LOCK ASSEMBLY.
THESE VEHICLES WERE CONSTRUCTED WITH WELDS IN THE REAR COMPARTMENT PAN ASSEMBLY THAT ARE NOT SUFFICIENT TO COMPLY WITH THE REQUIREMENTS PERTAINING TO FUEL TANK LEAKAGE IN THE EVENT OF A REAR IMPACT COLLISION. THE FUEL TANK ASSEMBLIES DO NOT COMPLY WITH FMVSS NO. 301, FUEL SYSTEM INTEGRITY.
PAINT ON THE WHEEL MOUNTING SURFACES CAN ACT AS A SHIM BETWEEN THE WHEEL AND THE ROTOR/DRUM. AS THE VEHICLE IS DRIVEN, THE WHEEL IMBEDS INTO THE PAINT, LOOSENING THE LUG NUT AND CAUSING A LOSS OF CLAMP LOAD.
THE ENGINE OIL COOLER INLET HOSE MAY HAVE BEEN INSTALLED TOO CLOSE TO THE STEERING GEAR CAUSING CHAFING. THE CHAFING CAN EVENTUALLY WEAR THROUGH THE HOSE'S PROTECTIVE SLEEVE RESULTING IN ENGINE OIL LEAKING ONTO THE ENGINE.
IN THE EVENT OF A PRIMARY ACCELERATOR CONTROL SPRING FAILURE, THE SECONDARY (BACK-UP) ACCELERATOR CONTROL RETURN SPRING WILL NOT RETURN THE THROTTLE TO THE FULLY CLOSED POSITION, AS REQUIRED BY FMVSS NO. 124, ACCELERATOR CONTROL SYSTEM.
DURING ASSEMBLY, WATER MAY HAVE ENTERED THE ACCELERATOR CONTROL CABLE CONDUIT CAUSING IT TO DEVELOP A HIGH EFFORT AND/OR BINDING CONDITION IN VERY COLD WEATHER.
THE CRUISE CONTROL CABLE MAY SEPARATE FROM THE CONDUIT END FITTING WHILE ENGAGED AND ACCELERATOR CONTROL COULD BE LOST.
THE NEUTRAL START SAFETY SWITCH COULD HAVE BEEN FRACTURED DURING INSTALLATION.
THE FUEL FEED HOSE CAN PULL OUT OF THE CRIMPED COUPLING AT THE ENGINE END OF THE HOSE ASSEMBLY, CAUSING FUEL LEAKAGE.
THE BRAKE HOSES WERE MANUFACTURED INCORRECTLY, AND DO NOT COMPLY WITH FMVSS 106, BRAKE HOSES.
THE DRIVER AND PASSENGER FRONT SEAT MANUAL RECLINING MECHANISMS DO NOT COMPLY WITH THE REQUIREMENTS OF FMVSS 207, SEATING SYSTEMS. THE SEAT BACK MECHANISMS WILL NOT LATCH UNDER CERTAIN CONDITIONS.
FRONT FUEL FEED HOSE ASSEMBLY COULD CRACK OR SEPARATE AT THE COUPLING ON THE ENGINE END OF THE HOSE ASSEMBLY, ALLOWING FUEL TO LEAK INTO THE ENGINE COMPARTMENT.
FRONT FUEL FEED HOSE ASSEMBLY COULD CRACK OR SEPARATE AT THE COUPLING ON THE ENGINE END OF THE HOSE ASSEMBLY, ALLOWING FUEL TO LEAK INTO THE ENGINE COMPARTMENT.
THE POWER SEAT OR RECLINER WIRING HARNESS CAN BE PINCHED OR CAN CHAFE ON THE SEAT FRAME OR SPRING SUPPORT ROD, WEARING THROUGH THE WIRE INSULATION AND CAUSING AN ELECTRICAL SHORT.
THE POWER SEAT OR RECLINER WIRING HARNESS CAN BE PINCHED OR CAN CHAFE ON THE SEAT FRAME OR SPRING SUPPORT ROD, WEARING THROUGH THE WIRE INSULATION AND CAUSING AN ELECTRICAL SHORT.
THE VEHICLES WERE ASSEMBLED WITH AN INCORRECT SUSPENSION UPPER SPRING SEAT AT THE RIGHT-REAR POSITION. IF THE VEHICLE IS INVOLVED IN A REAR IMPACT ACCIDENT, THE RIGHT-HAND REAR WHEEL HOUSE FLANGE COULD SEVER THE FUEL TANK FILLER PIPE AND SPILL FUEL.
THE SHOULDER BELT GUIDE LOOP PLASTIC COVERING MAY CRACK AND EXPOSE THE STEEL SUB-PLATE.
THE SHOULDER BELT GUIDE LOOP PLASTIC COVERING MAY CRACK AND EXPOSE THE STEEL SUB-PLATE.
THE OPTIONAL REMOTE ENTRY MODULE MAY HAVE A FAULT WHICH CAUSES RANDOM ACTUATION OF INTERIOR LAMPS, DOOR LOCKS, AND/OR TAILGATE RELEASE. THIS ACTUATION MAY OCCUR WHILE THE VEHICLE IS IN USE OR UNATTENDED.
MOISTURE CAN ENTER THE EXPRESS-DOWN ELECTRONIC CONTROL MODULE AND CAUSE A SHORT CIRCUIT THAT CAUSES WINDOW OPERATION WITHOUT OPERATOR CONTROL, AND LEAVES THE WINDOW IN THE DOWN POSITION.
THE FRONT DOOR SHOULDER BELT GUIDE LOOPS MAY BE CRACKED AND ARE NOT IN COMPLIANCE WITH FMVSS 208.
THE REVERSE SERVO APPLY PIN MAY BIND IN THE CASE WHICH COULD CAUSE REVERSE BAND DISTRESS (LOSS OR SLIPPING OF REVERSE), REVERSE BAND DRAG IN DRIVE RANGE (POOR PERFORMANCE -- POOR POWER), OR THE TRANSMISSION TO REMAIN IN REVERSE WHILE THE SHIFT INDICATOR SHOWS NEUTRAL GEAR POSITION.
THE REVERSE SERVO APPLY PIN MAY BIND IN THE CASE WHICH COULD CAUSE REVERSE BAND DISTRESS (LOSS OR SLIPPING OF REVERSE), REVERSE BAND DRAG IN DRIVE RANGE (POOR PERFORMANCE -- POOR POWER), OR THE TRANSMISSION TO REMAIN IN REVERSE WHILE THE SHIFT INDICATOR SHOWS NEUTRAL GEAR POSITION.
SECONDARY HOOD LATCH ASSEMBLIES CAN CORRODE, CAUSING A HIGH LATCH RELEASE EFFORT AND POSSIBLY PREVENTING THE HOOD FROM LATCHING PROPERLY WHEN IT IS CLOSED.
SECONDARY HOOD LATCH ASSEMBLIES CAN CORRODE, CAUSING A HIGH LATCH RELEASE EFFORT AND POSSIBLY PREVENTING THE HOOD FROM LATCHING PROPERLY WHEN IT IS CLOSED.
THE PASSENGER'S SIDE EASY-ENTRY SEAT ADJUSTER MAY FAIL FULLY LOCK INTO POSITION AFTER THE SEAT BACK HAS BEEN TILTED FORWARD AND THE SEAT SLID FORWARD, THEN RETURNED TO ITS ORIGINAL POSTITION.
A MISADJUSTMENT OF THE PARK LOCK CABLE IN THE COLUMN SHIFT ASSEMBLY MAKES IT POSSIBLE FOR THE STEERING COLUMN TO LOCK WHILE THE VEHICLE IS IN MOTION AND THE IGNITION SWITCH IS IN THE OFF POSITION.
FRONT SHOULDER SAFETY BELT WEBBING MAY SEPARATE AT FRONT BELT UPPER GUIDE LOOPS ON EITHER SIDE OF THE FRONT SEAT.
FRONT SHOULDER SAFETY BELT WEBBING MAY SEPARATE AT FRONT BELT UPPER GUIDE LOOPS ON EITHER SIDE OF THE FRONT SEAT.
