Just What Is a Car Recall? Car Safety Recall Definition - A safety recall is an automotive manufacturer's way of notifying vehicle customers that their product has a flaw. The automobile problem is serious enough that if you do not correct the flaw your and/or your passengers' safety could be at risk. Generally recalls are initiated by the US Government, but sometimes individual car manufacturers will pre-emptively initiate a recall.
Where Do I Find My VIN (Vehicle Identification Number)? Look on the lower left of your car’s windshield for your 17-digit Vehicle Identification Number (VIN). Your VIN is also located on your car’s registration card, and it may be shown on your insurance card.
Auto Tip - How Do I Find Out If My Vehicle Has A Recall? ==> An easy way to determine if you have an active car recall is to just enter your VIN number at the top of this page and CarFax will report if there are any issues at all with your vehicle.
THESE VEHICLES WERE ASSEMBLED WITH REAR OUTBOARD SAFETY BELT ANCHORAGES THAT MAY NOT WITHSTAND THE REQUIRED LOAD. THIS DOES NOT COMPLY WITH FMVSS NO.210, SEAT BELT ASSEMBLY ANCHORAGES.
THESE VEHICLES WERE ASSEMBLED WITH REAR OUTBOARD SAFETY BELT ANCHORAGES THAT MAY NOT WITHSTAND THE REQUIRED LOAD. THIS DOES NOT COMPLY WITH FMVSS NO.210, SEAT BELT ASSEMBLY ANCHORAGES.
THESE VEHICLES WERE ASSEMBLED WITH REAR OUTBOARD SAFETY BELT ANCHORAGES THAT MAY NOT WITHSTAND THE REQUIRED LOAD. THIS DOES NOT COMPLY WITH FMVSS NO.210, SEAT BELT ASSEMBLY ANCHORAGES.
THESE VEHICLES WERE ASSEMBLED WITH REAR OUTBOARD SAFETY BELT ANCHORAGES THAT MAY NOT WITHSTAND THE REQUIRED LOAD. THIS DOES NOT COMPLY WITH FMVSS NO.210, SEAT BELT ASSEMBLY ANCHORAGES.
THESE VEHICLES WERE ASSEMBLED WITH REAR OUTBOARD SAFETY BELT ANCHORAGES THAT MAY NOT WITHSTAND THE REQUIRED LOAD. THIS DOES NOT COMPLY WITH FMVSS NO.210, SEAT BELT ASSEMBLY ANCHORAGES.
THE RIGHT HAND SPINDLE NUT WAS NOT PROPERLY TIGHTENED DURING ASSEMBLY. THIS CAN CAUSE PREMATURE WHEEL BEARING FAILURE AND OVER TIME, THE SPINDLE CAN FRACTURE.
WATER INTRUSION CAN CAUSE A SHORT CIRCUIT IN THE POWER DOOR LOCK ASSEMBLY.
IN THE EVENT OF A PRIMARY ACCELERATOR CONTROL SPRING FAILURE, THE SECONDARY (BACK-UP) ACCELERATOR CONTROL RETURN SPRING WILL NOT RETURN THE THROTTLE TO THE FULLY CLOSED POSITION, AS REQUIRED BY FMVSS NO. 124, ACCELERATOR CONTROL SYSTEM.
THE POWER SEAT OR RECLINER WIRING HARNESS CAN BE PINCHED OR CAN CHAFE ON THE SEAT FRAME OR SPRING SUPPORT ROD, WEARING THROUGH THE WIRE INSULATION AND CAUSING AN ELECTRICAL SHORT.
FUEL FEED HOSE COULD LEAK AT THE COUPLING ON THE ENGINE END OF THE HOSE ASSEMBLY.
POOR BOND ADHESION BETWEEN THE WINDSHIELD GLASS AND MOUNTING COULD ALLOW THE WINDSHIELD TO SEPARATE DURING A 30 MPH FRONTAL BARRIER TEST REQUIRED BY FMVSS 212.
THE FUEL SYSTEM MAY LEAK AT THE THROTTLE BODY INJECTION FUEL FEED PIPE CONNECTION. CONSEQUENCE OF DEFECT: THIS LEAKAGE COULD RESULT IN AN UNDERHOOD FIRE WHICH COULD SPREAD TO THE PASSENGER COMPARTMENT AND CAUSE BURN INJURIES TO OCCUPANTS.
SOME VEHICLES HAVE BUCKET SEAT BACK LOCKS THAT DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD 207, ANCHORAGE OF SEATS. IN EVENT OF A CRASH, THE SEAT BACK LOCK MAY NOT FUNCTION.
THE BRAKE PROPORTIONER VALVES MAY BREAK AND SEPARATE FROM THE MASTER CYLINDER. THIS WOULD ALLOW BRAKE FLUID TO LEAK AND WOULD RESULT IN A PARTIAL LOSS OF THE BRAKE SYSTEM.
